QUIKCELL OnBeat360 Portable Wireless Speaker User Guide
- October 30, 2023
- QUIKCELL
Table of Contents
QUIKCELL OnBeat360 Portable Wireless Speaker User Guide
SPECIFICATION
- Driver Size : Two 40mm Dynamic Drivers
- Bluetooth Version: 5.0
- Speaker Materials: ABS/iron net/Silicone
- Weight: 12oz
- Battery Type: Lithium Ion
- Speaker Power: 5W x2’/
- Charging Time (hours from empty): 3-3.5hrs”
- Music Playtime (volume at 50%): 18hrs
- Tiempo de Reproducción de Música (volumen al 50%): 18 hrs
- Talk Time (volume at 50%): 18hrs
- Tiempo de Conversación (volume al 50%): 18 hrs
- Frequency Response: 20Hz-20KHz
- Frecuencia de Respuesta : 20Hz-20KHz
- Water resistant: IP65
- Resistencia al Agua : IP65
- Wireless Connection Range : 33ft
- Rango de Conexión Inalámbrica : 10 metros
WHAT’S INSIDE
-
Wireless Speaker
Altavoz Inalambrico -
Built-in Carrying Strap
Correa -
Micro-USB Charging Cable
Cable de Carga Micro USB -
Carabiner Clip
Carabina
HEADPHONE CONTROLS
- 1. Power Button
- Long Press = power off/on
- [—] Button
- Long Press = skip to previous song
- Short Press = decrease volume
- [Play, Pause, Answer] Button
- Short Press = play/pause music & answer/end phone calls
- Long Press = ignore/decline phone calls
- Double Press = redial last dialed number
- TWS Pairing Button
- Short Press = enter/exit TWS pairing mode
- Long Press (3 seconds) = Pair to another smartphone
- Long Press (6 seconds) = clear device pairing history
- Microphone
- LED indicator
- USB charging light
- Reset button
CHARGING YOUR SPEAKER
Plug the Micro-USB tip of your charging cable into your speaker and the USB-A tip into a compatible port (such as a wall charger, car charger, or computer). Light is RED while charging and turns GREEN when fully charged. Allow your speaker to fully charge for 3-3.5 hours prior to first use.
Use the included USB charging cable to connect your OnBeat 3600 to a compatible charging port.
Use el cable de carga USB incluido para conectar su OnBeat 360° a un adaptador de carga compatible.
“USB charging port not included. Requires at least a 5V/1A charging port
”El adaptador de carga USB no está incluido. Requiere por lo menos un adaptador de carga úiV/fA.When you turn on your OnBeat 360° for the first time, it will automatically enter pairing mode. You will see the BLUE indicator light flashing and can then search for “OnBeat 360” in your devices Bluetooth settings. When your device is paired you will hear a connection tone.
if you would like to pair another device to your OnBeat 360°, you can do so a couple different ways.
Si desea emparejar otro dispositivo a su OnBeat 360″, puede hacerlo de dos formas:
Option 1 : Turn off the Bluetooth for the device that is already connected. You will then hear a tone to know it has been disconnected and see the BLUE indicator light flashing. You can now search for “OnBeat 360” in your other devices settings to connect.
Option 2 : Long press the TWS Button for 3 seconds until you hear the
connection tone an see the BLUE indicator light flashing. You can now search
for “OnBeat 360” in your other devices settings to connect. : Long press the
TWS Button for 3 seconds until you hear the connection tone an see the BLUE
indicator light flashing. You can now search for “OnBeat 360” in your other
devices settings to connect.
BLAST THE SOUNDL
Use the POWER BUTTON to turn your OnBeat 360” ON/OFF.
Use the + and – buttons to adjust volume and skip songs.
Use the PLAY/PAUSE button to control music and answer, end, or decline phone calls.
Connect to a phone by long pressing the TWS Button for 3 seconds.
”Your OnBeat 360° will turn off after 10 minutes if a device is not connected,
your device is out of range, or your Bluetooth is turned off
PAIRING WITH ANOTHER ONBEAT 360
To use the OnBeat 360°’s TWS setting, you will need to ensure the other OnBeat 360° is within range and that neither speaker is connected to a smartphone, then short press the TWS Button on each speaker to begin pairing. When you see the indicator light flashing BLUE, followed by the connection tone your speakers are paired, and you may now pair them with your phone by selecting “OnBeat 360” in your Bluetooth settings.
”When speakers are in TWS mode, all functions are linked. Meaning, you only
need to use confro/s on one of the speakers to control both.
HOW MUCH POWER DO HAVE
You can check the battery percentage on your smartphone by doing the following:
Apple iOS 14 and up: From your home screen, swipe left to go to your “today View”. From here long press any existing widget and select “Edit Home Screen” to go into jiggle mode. Then, look for the + in the top left corner to search for the battery widget. You can then choose the size widget that works for you – small, medium, or large. This will now show you the battery level of all connected devices.
Android Oreo (8.1) and up: In Settings go to “Connections” Tap on the word “Bluetooth” (not the switch next to it) and you will see complete list of all connected devices and their battery level.
Apple
Android
Additionally, when your OnBeat 360° reaches 20% power, you will hear “Battery Low” every 2 minutes. If it reaches 5% power, it will turn of automatically.
PamobeeribrmmitmzobrelagaanJa,vii
A lphacomm.
^c 2B21 UI rights reserved. Alpha Comm and Quikcell are registered trademarks
o4 Alpha Comm
ONE YEAR LIMITED WARRANTY
For warranty information, please visit Para obtener informaci6n sobre la
garantia, visite quikcell.com/warranty
Alphacom m_
© 2021 All rights reserved. Alpha Comm and Quikcell are registered trademarks of Alpha Comm Enterprises. All other trademarks are the property of their respective owners. Designed by Alpha Comm Enterprises at 1500 Lakes Parkway; Lawrenceville, GA 30043. Diseriado por Alpha Comm Enterprises en 1500 Lakes Parkway, Lawrenceville, GA 30043.
OnBeat 360°
ONBEAT360
FCC ID: 2AEZG-0260
Alpha Comm Enterprises Inc.
1500 Lakes Parkway Lawrenceville GA 30043.
1-888-951-0909
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.