Infinity KP3002 Kappa Perfect PowerSports Amplifiers Owner’s Manual

Infinity Kappa Perfect PowerSports
AMPLIFIERS OWNER’S MANUAL

THANK YOU FOR YOUR PURCHASE . . .
Your product has been designed to provide you the performance and ease of operation you expect from Infinity. Take time to read this manual before operating or installing your amplifier. This manual describes general installation guidelines and operation instructions. Please note that  proper installation of mobile audio components requires qualified experience with mechanical and electrical procedures. If you do not have the knowledge and tools to perform this installation, we strongly recommend consulting an authorized Infinity dealer about your installation options.

WHAT’S IN THE BOX

1. amplifier
2. tie wraps
3. spare fuse
4. Stainless steel mounting hardware
5. Black zip ties
6. Infinity stickers
7. end panel covers
8. owner’s manual

INSTALLATION AND WIRING

IMPORTANT: Disconnect the vehicle’s negative (–) battery terminal before beginning the installation.
Mounting the Amplifier

• Wear protective eyewear when using tools.
• Choose a safe mounting location. Check clearances on both sides of the location. Be sure that screws will not puncture brake or fuel lines or wiring harnesses, and that wire routing will not interfere with vehicle operation. Use caution when drilling or cutting.
• When making electrical connections, make sure they are secure and properly insulated.
• Do not mount the amplifier with the heat sink facing downward, as this interferes with cooling.
• Using the amplifier as a template, mark the locations of the holes on the mounting surface.
• Drill pilot holes in the mounting surface.
• Attach the amplifier to the mounting surface with sheet metal screws.

Wiring the Amplifier
Kappa Perfect amplifiers feature wire plugs that allow you to make all connections using optional mating connectors (sold separately). You can also remove the plugs to make direct wiring connections.
Power and Ground Connections Using an Optional Mating Connector

• First, prepare the mating connector (sold separately) in the vehicle. Strip a short length of the jacket from the power, ground, and remote turn-on wires from the vehicle. Crimp the terminals onto the ends of each wire. Insert each wire into the appropriate pin location in the mating connector housing (see chart below). Push firmly to secure the wires in the housing, then snap the back panel of the housing into place.
• When all connections are made, plug the connector from the amplifier into the mating connector.

Mating power wire terminals part number: KP3002: HRB T9910PS-2
KP5004: HRB T9910PS-2A for remote turn-on,
T9910-2A for Power and Ground
Mating connector housing part number: HRB P9910-3-B-H-A/B
Mating connector housing HRB P9910-3-B-H-A/B wire configuration

Power and Ground Connections – Direct Hardwire

• Use wire cutters to remove the connector from the amplifier wiring harness. Then, strip a short length of the jacket from each wire.
• Power: Connect the +12V power wire to the positive terminal of the vehicle’s battery. Make sure the fuse and fuse holder are within 18″ (457mm) of the battery.
• Ground: Connect the GND wire to the negative terminal of the vehicle’s battery, or to the vehicle’s chassis near the battery with a screw. NOTE: If possible, remove any paint from the chassis for best contact. It’s recommended to use a star washer below the ring connector for a secure connection.
• Remote: Connect the remote turn-on wire to the “Remote Out” lead of the source unit, if using low-level signal inputs with an aftermarket stereo. NOTE: If you’re using high-level signal inputs (your vehicle’s speaker wires), the Kappa Perfect amplifier’s 12-volt DC offset feature will turn the amplifier on when it senses audio signal. In this case, you will not have to connect the remote turn-on wire and can tape or cap it off to prevent the introduction of noise.

Power/Protect indicators
The power light will illuminate in green when the amplifier is getting power and playing. The light will illuminate in red if the amp enters protect mode in the event of conditions such as over/under voltage, short circuit, amplifier output circuit failure, or excessive heat.
Line-level Signal Input

• If your source unit offers preamp outputs, connect to the amplifier’s L and R preamp inputs using RCA patch cables.

Speaker-level Signal Input

Speaker-level Input with Optional Mating Connectors

• If your audio system’s source unit does not have line-level outputs, connect the speaker-level input wires from the amplifier to the front and/or the rear speaker output wires of your source unit.
• If using the amplifier wiring plugs, first, prepare the mating connector (sold separately) in the vehicle. Strip a short length of the jacket from the speaker wires coming from the source unit in the vehicle. Crimp the terminals onto the ends of each wire. Insert each wire into the appropriate pin location in the mating connector housing (see chart below). Push firmly to secure the wires in the housing.
• When all connections are made, plug the amplifier connector into the mating connector.Mating power wire terminals part number: Molex 039000039
  Mating connector housing part number: Molex 039012040

Mating connector housing 039012040 wire configuration for front channels (KP5004 and KP3002)

Mating connector housing 039012040 wire configuration for rear channels (KP5004 only)

Speaker-level Input – Direct Connection

• Use wire cutters to remove the connector from the amplifier wiring harness. Then, strip a short length of the jacket from each wire.
• Splice the speaker-level input wires for the amplifier to the speaker wires coming from the source unit in the vehicle. Use solder, butt connectors, or your preferred splicing method. The 12-volt DC offset feature will turn the amplifier on when it senses signal.

INPUT LEVEL SELECTION

If you’re sending signal to the amplifier using low-level outputs from your source unit, slide the input level selector to “LO.” If using high-level outputs from your source unit, slide the selector to Speaker Output Connections
Speaker Output with Optional Mating Connectors

• If using the amplifier wiring plugs, first, prepare the mating connector (sold separately) in the vehicle. Strip a short length of the jacket from the speaker wires going to the speakers in the vehicle. Crimp the terminals onto the ends of each wire. Insert each wire into the appropriate pin location in the mating connector housing (see chart below). Push firmly to secure the wires in the housing
• When all connections are made, plug the amplifier connector into the mating connector.Mating power wire terminals part number: Molex 039000077 (KP5004) or 039000039 (KP3002)
  Mating connector housing part number: Molex 039039042

Mating connector housing 039039042 for all channels (KP5004 and KP3002), terminal 030000039 for front channels (KP3002), terminal 039000077 for all channels (KP5004)

Speaker Output – Direct Connection

• Use wire cutters to remove the connector from the amplifier wiring harness. Then, strip a short length of the jacket from each wire.

• Connect your speakers to the amplifier’s speaker output wires, observing proper polarity: connect each amplifier’s positive (+) lead to the appropriate positive (+) speaker terminal, and negative (-) lead to the appropriate negative (-) speaker terminal. NOTE: Speaker-wire extensions might be necessary.

• KP5004 4-channel operation: Connect the front left speaker leads (white and white/black) to the front left speaker’s + and – terminals, and the front right speaker leads (gray and gray/black) to the front right speaker’s + and – terminals. Next, connect the rear left speaker leads (green and green/black) to the rear left speaker’s + and – terminals, and the rear right speaker leads (violet and violet/black) to the rear right speaker’s + and – terminals.

• KP5004 3-channel (bridged) operation: Connect the front left speaker leads (white and white/ black) to the front left speaker’s + and – terminals, and the front right speaker leads (gray and gray/black) to the front right speaker’s + and – terminals. Next, connect the rear left + speaker lead (green) to the single speaker’s + terminal, and the rear right – speaker lead (violet /black) to the single speaker’s – terminal.
  NOTE: To prevent electrical interference or short-circuiting, terminate the unused speaker leads with a wire cap or electrical tape.

• KP5004 2-channel (bridged) operation: Connect the front left + speaker lead (white) to the front single speaker’s + terminal, and the front right – speaker lead (gray/black) to the front single speaker’s – terminal. Next, connect the rear left + speaker lead (green) to the rear single speaker’s + terminal, and the rear right – speaker lead (violet /black) to the rear single speaker’s – terminal.
  NOTE: To prevent electrical interference or short-circuiting, terminate the unused speaker leads with a wire cap or electrical tape.

• KP3002 2-channel operation: Connect the left speaker leads (white and white/black) to the left speaker’s + and – terminals, and the right speaker leads (gray and gray/black) to the right speaker’s + and – terminals.

• KP3002 bridged operation: Connect the amplifier’s left positive (+) wire (white) to the single speaker’s + terminal, and the right negative (-) wire (gray/black) to the speaker’s – terminal.
  NOTE: To prevent electrical interference or short-circuiting, terminate the unused speaker leads with a wire cap or electrical tape.

SETTING THE SOUND

Setting the input level
To match your amplifier’s input sensitivity (gain) to your source unit’s output level, we recommend the following procedure:

• Turn the input level control counterclockwise to MIN (minimum).
• Play a dynamic music track through your source unit. Turn the source unit’s volume control to the 3/4 position.
• Turn the input level control dial clockwise towards MAX until you hear distortion in the music (it’s no longer clear), then turn it counterclockwise until the music sounds clear again. Your input sensitivity is now set.

Crossover filters
You can adjust your Kappa Perfect amplifier’s filters to suit your listening preferences and speaker configuration.
The KP5004 lets you select either no filter (OFF) for a full-range signal, or a high-pass filter (HPF) for your front channels if you’re powering a subwoofer with the rear channels. Slide the switch to choose your desired crossover point.
For the rear channels, you can select between no filter (OFF); a high-pass filter (HPF) if you’re powering a subwoofer independently, or a low-pass filter (LPF) if you’re using the rear channels to power a subwoofer in bridged mode. Slide the REAR – HZ switch to choose your desired crossover point.

The KP3002 lets you slide the X-OVER switch to select no filter (OFF) for a full-range signal; a high-pass filter (HPF) if you’re powering speakers and have an independently powered subwoofer in your system; or a low-pass filter (LPF) if you’re powering a subwoofer in bridged mode. Slide the FREQ. switch to choose your desired crossover point.

The KP3002 also includes a bass boost (BOOST) switch for a +6dB or +12dB boost at 45 Hz.

SPECIFICATIONS

Signal-to-noise ratio (reference
to 1 watt):| >75dB| >75dB
THD + N at rated power:| <1%| <1%
Frequency response:| 20Hz – 20kHz| 20Hz -20KHz
Crossover filter| Front HPF 60H, 80Hz,
120Hz selectable @
12/dB/octave; Rear LPF/ HPF 60Hz, 80Hz, 120Hz selectable @ 12dB/octave| OFF/HPF/LPF 60Hz,
80Hz, 120Hz selectable @ 12dB/octave
Bass boost| N/A| 0, +6dB, +12dB selectable @45Hz (only when LPF is
engaged)
Amplifier Class| Class D| Class D
Turn-on Modes| 12V & DC offset| 12V & DC offset
Recommended wire gauge| 10 AWG| 10 AWG
Dimensions (H x W x D):| 9.339″ (237.2mm) W x 1.75″ (45mm) H x 3.35″ (85mm) D| 8.157″ (207mm) W x 1.75″ (45mm) H x 3.35″ (85mm) D
Weight| 1101.6 g| 912.8 g

TROUBLESHOOTING

terminals, or bad or no ground connection. Check voltages at amplifier terminals with VOM.
No audio and PROTECT INDICATOR flashes every 4 seconds.| DC voltage on amplifier output. Amplifier may need service; see enclosed warranty card for service information.
No audio and PROTECT and POWER INDICATORS flash.| Voltage less than 9V on BATT+ connection. Check vehicle charging system.
No audio and PROTECT INDICATOR is on.| Amplifier is overheated. Make sure amplifier cooling is not blocked at mounting location. Verify that speaker- system impedance is within specified limits. Or, there may be voltage greater than 16V (or less than 8.5V) on BATT+ connection. Check vehicle charging system.
Amplifier fuse keeps blowing.| The wiring is connected incorrectly or there is a short circuit. Review installation precautions and procedures. Check wiring connections.
Distorted audio.| Gain is not set properly. Check INPUT LEVEL setting. Check speaker wires for shorts or grounds. Amplifier or source unit may be defective.
Distorted audio and PROTECT INDICATOR flashes.| Short circuit in speaker or wire. Remove speaker leads one at a time to locate shorted speaker or wire, and repair.
Music lacks dynamics or “punch.”| Speakers are not connected properly. Check speaker connections for proper polarity.

HARMAN International
Industries, Incorporated
8500 Balboa Boulevard,
Northridge, CA 91329 USA
www.infinityspeakers.com

© 2022 HARMAN International Industries, Incorporated. All rights reserved.
Infinity is a trademark of HARMAN International Industries, Incorporated, registered in the United States and/or other countries. Features, specifications and appearance are subject to change without notice.
CA_Infinity Kappa Perfect Power Sports Amplifiers_KP3002+KP5004_OM_US_SOP_V7_8in×11in_EN
Safety Instruction
PRODUCT REGISTRATION
register.infinityspeakers.com
SIGN UP & STAY TUNED Register your product
‘Product registration may no! be available for all countries

https://register.infinityspeakers.com/?utm_source=qr_code&utm_medium=w_and_s&utm_campaign=w_and_s

Download the full warranty card and safety information and other helpful information from our website: www.infinltyspeakers.com/warrantyandsafetybooks

https://www.infinityspeakers.com/warrantyandsafetybooks

IMPORTANT SAFETY INSTRUCTIONS
For all products:

1. Read these Instructions
2. Keep these imitations.
3. Find all wamings
4. Follow all Marriott’s
5. Clean only with a dry cloth_
6. Do not block any ventilation openings.. Install this apparann in accordante with the manufacturer’s instructions
7. Do not install this apparatus near any twat sources such as radiators, heat registers, suns or other apparatus (including amplifiers} that produce heat
8. Do not defeat the safety purposed the notarized Of gmunding-type plus A polarized Mug has two blades with one wider than the other. A grounding type plug has two blades and a thud rounding prong. The wide Made or the third prong is provided rot your safety_ If the provided plug does not hut into your outlet, consult an Seaman for replacement of the obsolete outlet.
9. Protect the power cad from being wafted on or pinched, particularly at plugs, commence receptacles and the point where they nit from the apparatus.
10. Use only attachments/accessories specified by the manufacturer
11. Use only with the cart, stand. tripod, bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when mantic the (art./apparatus combination to avoid injury from tip
12. Unplug this apparatus during lightning storms or when unused tor long periodsof time.
13. Rehr all senkirigto gualltled stroke personnel. Servicing is required when the apparatus has been damaged in any wry, such as when the power—amply cord ot plug n damaged., liquid has been spilled or objects have fallen into the apparatus, or the apparatus has been reposed to rain or moisture, does not operate normally in has been dropped
14. to disconnect this apparatus from the AC mains usinMetely, disconnect the power- supply cord pha; from the AC receptacle.
15. The meths Ow; of the power-supply cord shall remain readily operable.
16. This apparatus is intended to be used only with the power supply and/or charging cable provided by the manufacturer.

The following instructions may not apply to waterproof devices. Refer to your device user manual or quick start guide for more waterproof instruction if any. • Do not use this apparatus near water. • De not expose this apparatus to dripping or splashing and ensure that no selects idled with liquids, such as vases, are placed on the apparatus WARNING: TO REDUCE THE MX OF FIRE OR ELKTRK SaK/CK, DO NOT EXPOSE THIS APPARATU510 MIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
THIS SYMBOL ON THE PRODUCT MEANS THERE IS UNINSUtATED, DANGEROUS VOLTAGE WITHIN THE PRODUCT ENCLOSURE THAT MAY PRESENT A RISK OT ELECTRICAL SHOCK
THIS SYMBOL ON THE PRODUCT MEANS THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THIS GUIDE.
CAUTION FCC AND K STATEMENT FOR USERS IUSA AND CANADA ONLY)
This dente complies with part 15 of the FCC Rules_ Operation Is sublet to the following two conditions: (1) This device may not cause harmful interference. and (I) this device must accept any interference reeved, including interference that may cause undesired operation. CAN KES-003(131/11M8- 003181
FCC SDO( SUPPLIER’S DECLARATION OF CONFORMITY HARMAN
International hereby declares that this equipment is in complws-wah the FCC Pad 15 Subpart B The declaration ol conformity may be consulted in the support section of Web site, accessible front www.mhnityspeaken.com Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for (lass B digital device, pursuant to Pan 15 of the FCC Rules These Iamb are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates, uses and can radiate radio frequency energy and, If not installed and used in accordance with the instructions, may cause harmful inteferena to radio communications However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or
television reception. which can be determined by turning the equipment off and on, the uses rs encouraged to try to coned the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and reeve
• Connect the equipment into an outlet on a urtutt different horn that to which the reeve is connected.
• Consult the dealer or an experienced radinf1V technician for help.
  Caution. Changes or mediations not expressly approved by HARMAN could void the user’s authority to operate the equipment.

For Products That Transmit RF Energy:
(I) FCC AND IC INFORMATION FOR USERS This device complies with Part 15 of the FCC rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. Om device may not cause harmful intetference, and
2. this device must accept any interference received. tritluding interference that may cause undimmed operation (H)KCJH Radiation Exposure Statement This equipment complies with FCC and ND radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. In case this equipment has to subject to FCGIC SAR (Specific Absorption Rate) exposure test, this equipment is designed to meet the requirements for exposure to radio waves established by the FCC and KED These requirements set a SAR limit of 1 6 WAg averaged over one Beam of time The highest SAR value reported under this standard dung product septic/Rion for use when properly worn on the body or on the head, with no separation. To meet Rf exposure guidelines and reduce exposure to RF energy during the operation. this equipment should be positioned at least this distance away from the body or the head. For radio equipment operates in 5150-58SOMHz FCC and IC Caution: High power radars are allocated as primary users of the 5 25 to 535 GHz and 5.65 to S 85 GHz bands. These radar stations can cause interference with and/or damage to t E LAN (Lkexe-Exempt lord Area Network) devices No configuration controls are provided for this wireless equipment allowing any change in the frequency of operations outside the FCC grant of authorization for US operation according to Part 15.407 of the EC( rules.
IC Caution: Use should also be advised that
(I) The device for operation in the band 5150 – 5250 MHz is only lot uidom use to reduce the potential for harmful interference to co-channel mobile satellite systems, (n) the maximum antenna gain permitted for devices in the bands 5250 5350 MHz and 5470 – 5715 MHz shall comply with the ettp. lima and OH The maximum antenna gain permitted for devices in the banc151)5 -5825 MHz shall comply with the ecr p. limits specified for point-to-point and non point to-poem operation as appropriate_
Use Restriction Attention in European Union, operation is limited to indoor use within thtn the band 5150-5350 MHz
C orrect disposal of this product (Waste Electrical & Electronic Equipment)
This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate chc4ellpsectprffinoteafaanatinyurtreresourcgtling-e:, hrermandis MheaMisalaann4d trheeyding environment For more Information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product .
This product is RoHS compliant.
This product is in compliance with Directive./011/65/EU and UK The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 1012, and its amendments, on the electronic equipmentmen thereness of certain hazardous substances in electrical
REACH
REACH (Regulation No 1907/2006) addresses the production and use of chemical substances and their potential impacts on human health and the environment Article 33(1) of REACH Regulation requires suppliers to inform the recipients if an article rectum more than 0.1 % (per weight per article) of any substances) on the Substances of Very High Concern (SVEK1Candidate llst (REACH candidate list) This product contains the substance “leaCi-CAS No. 7439-91-1)in a concentration of more than 0 I% per weight M the time of release of this product, except for the lead substance, no other substances of REACH candidate list are contained in a concentration of more than 0.1% per weight In this product Note: On lune 17, 2018. lead was added to the REACH candidate tut, the inclusion of lead in the REACH candidate list does not mean that lead-containing materials pose an immediate Alter m00 wiser°, L,WS of permissibility of its use. Go to Settings to active i
For devices with headphone Jacks
WARNINGS/CAUTIONS
Do NOT u~ thf headphones at a high volume for any extended peened. -To .rood henna damage,~ your headphones al a comfortable, moderate volume law. -Tum that volume down on your devkit before placing the headphones on your ms, then tum thf volume up gradually untff you reach a comfonable hsteninq level.
For Products That Include Batteries Instructions for ~en on Removal, RKyChng and Disposal of~
Batteries
To roomy the battens from your equipment or remote control, riffle that procedure described In the owne(s manual for 1111ert1nq batteries. for procure with a built-in battery that lets for the hftt1me of the product, removal may not be posslblt for the user. In this ca~. recycling or recovery centers handle the diSmantl1ng of the product and the removal ofthe battery. If, for any rea<on, it becomes necessary’s to replace such a battery, this procedure must be performed by authorized servKe centers. In the European
Union and Oher location~ it is illegit lo despot of MIY battery with housel laths. All battens must be dospo~ of in an environmentally soond manntr. Contact your obol wane-managtment officials for Information regarding the env,ronmentally soond collection, recycling and disposal of used bathos.
WARNING: ** Da~ of eXl)logion battery ,s ,incorrectly replaced. To reduce risk of fire, explosion or leakage of 11.lmmable liquid/gas, don’t disassemble, oust, puncture, short external contacts, ••~ to temperature above 60″( (140’f), sunshine or like, expose to extrffl low ,m pressure or dis~ of In fire or wattr. Replace only with specifitd batteries. The symbol ladykilling •~parade collection’ for all batteries and accumulators shall be the als~-out whteled bin shown below:
WARNING – For Products Contain Coin/Button Cell Batteries
00 NOT INGEST BATTERY, CHEMICAL BURN HAZARD. This product contains ii coin/button cell battery If the coin/button cell battery is swallowed, retcon cass~ severe internal bums In Just 2 hours and can lead to death. Keep new and used batteries away from children. If thf battery compartment does not close securely, stop using the product and ketp rt away from children. If you think batteries might have been swallowed or placed lnSlde any pan of the body, ~k lmmedi.Jte medical attentoon.
For All Products with Wireless Operation: HARMAN International hereby declares that this equipment Is In compliance with the essential requirements and other relevant provisions of Oracle 2014/53/EU and UK Radio Equipment Regulation, 2017. The declaration of conformity may be consulted in the support section of our Wth site, acces~ble from www.nfinltyspeakers.com.
HARMAN International lndullnes, Incorporated. All righll rese,vt<f. lnfimty ,s a trademaril or HARMAN lnttrnationil Industries, Incorporated, registered in the United States ilnd/or other countries. features, speoficallons and appearance are subject to change without nollce. [www.infinltyspeakers.com**](http://www.infinltyspeakers.com)

HARMAN
HARMAN lntPrnat1ondl lndustril”> ln(orµoutt-d
8500 Balboa Boul~vard. Northndgc, CA 91 :19 U~A
SSH2020-002
516 2′>54545 1USA only!
INFINITY KAPPA PERFECT POWER SPORTS AMPLIFIERS

https://gtly.to/Judxxgh3V
https://harman.widen.net/s/twsrspspfb/ca_infinity-kappa-perfect-power- sports­amplifiers_kp3002kp5004_om_us_sop_v7_8in11in_en

HARMAN International
Industries, Incorporated
8500 Balboa Boulevard,
Northridge, CA 91329 USA
www.infinityspeakers.com
C 2022 HARMAN International Industries, Incorporated.
All rights reserved.
Infinity is a trademark of HARMAN International Industries, Incorporated, registered in the United States and/or other countries. Features, specifications and appearance are subiect to change without notice.
CA_lnfinity Kappa Perfect Power Sports Amplifiers_QSG_USSOP V3

References

• Infinity US
• CA_Infinity-Kappa-Perfect-Power-Sports-Amplifiers_KP3002KP5004_OM_US_SOP_V7_8in11in_FR.pdf
• CA_Infinity-Kappa-Perfect-Power-Sports-Amplifiers_KP3002KP5004_OM_US_SOP_V7_8in11in_EN.pdf
• CA_Infinity-Kappa-Perfect-Power-Sports-Amplifiers_KP3002KP5004_OM_US_SOP_V7_8in11in_ES.pdf

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>