reolink 58.03.005.0002 Argus Eco Solar Powered Security Camera Instruction Manual

reolink 58.03.005.0002 Argus Eco Solar Powered Security Camera

Product Information

The Reolink Argus Eco is an outdoor security camera that comes with a rechargeable battery and a micro USB port for charging. It has a built-in PIR motion sensor and a daylight sensor. The camera has a status LED that indicates the WiFi connection status and the camera’s working status. The camera can be mounted on a wall or attached to a tree using the provided strap and security mount. The PIR detection range can be customized through the Reolink App.

Product Usage Instructions

Charge the Battery

Before mounting the camera outdoors, it is recommended to fully charge the battery. You can charge the battery using a power adapter (not included) or a Reolink Solar Panel (not included if you only purchase the camera). The charging indicator LED will turn orange when the battery is being charged and green when it is fully charged. Always cover the USB charging port with the rubber plug after charging for better weatherproof performance.

Install the Camera

When installing the camera, make sure to install it angularly to ensure proper motion detection. The camera should be mounted at a height of 2-3 meters with a PIR detection distance of 2-10 meters.

Mount the Camera to the Wall

1. Drill holes in accordance with a mounting hole template and screw the security mount into the wall. If you are mounting the camera on any hard surface, insert plastic anchors into the holes first.
2. Screw the antenna to the camera and then install the camera to the security mount.
3. Loosen the adjusting knob on the mount and adjust the camera to the proper direction.
4. Tighten the adjustment knob to lock the camera in place.

Attach the Camera to a Tree

1. Thread the provided strap to the mounting plate.
2. Attach the plate to the security mount with the smaller screws.
3. Fasten the security mount to a tree.
4. Install the camera and adjust the camera angles as instructed in step 3 of the wall mounting installation guide.

Notes on PIR Motion Sensor

The PIR detection range can be customized to meet your specific needs through the Reolink App. Refer to the table in the device settings of the app for setting up the PIR detection range.

Technical Support

If you need any technical help, please visit our official support site and contact our support team before returning the products, https://support.reolink.com.

What’s in the Box

Camera Introduction

Set up the Camera

• Download and launch the Reolink App or Client software, and follow the onscreen instructions to finish the initial setup.

On Smartphone

• Scan to download the Reolink App.

On PC

• Download the path of the Reolink Client: Go to https://reolink.com > Support > App & Client.

Charge the Battery

• It’s recommended to fully charge the battery before mounting the camera outdoors.
• Charge the battery with a power adapter. (not included)
• Charge the battery with Reolink Solar Panel (Not included if you only purchase the camera).
• For better weatherproof performance, please always cover the USB charging port with the rubber plug after charging the battery.

Charging indicator

• Orange LED: Charging
• Green LED: Fully charged

Install the Camera

• Install the camera 2-3 meters (7-10 ft) above the ground. This height maximizes the detection range of the PIR motion sensor.
• For better motion detection performance, please install the camera angularly.

NOTE: If a moving object approaches the PIR sensor vertically, the camera may fail to detect motion.

Mount the Camera to the Wall

• Drill holes in accordance with a mounting hole template and screw the security mount into the wall. If you are mounting the camera on any hard surface, insert plastic anchors into the holes first.
• Screw the antenna to the camera and then install the camera to the security mount.
• Lose the adjusting knob on the mount and adjust the camera to the proper direction.
• Stiffen the adjustment knob to lock the camera.

Attach the Camera to a Tree

• Thread the provided strap to the mounting plate.
• Attach the plate to the security mount with the smaller screws.
• Fasten the security mount to a tree.
• Install the camera and adjust the camera angles as instructed in step 3 in the previous installation guide.

Notes on PIR Motion Sensor

PIR Sensor Detection Distance

The PIR detection range can be customized to meet your specific needs. You can refer to the following table to set it up in Device Settings via Reolink App.

Sensitivity

| ****

Value

| Detection Distance

(For moving and living objects)

---|---|---
Low| 0 – 50| Up to 5 meters (16ft)
Mid| 51 – 80| Up to 8 meters (26ft)
High| 81 – 100| Up to 10 meters (33ft)

NOTE: Higher sensitivity offers a longer detection distance but it may lead to more false alarms. It’s recommended to set up the sensitivity level to “Low” or “Mid” when you install the camera outdoors.

Important Notes on Reducing False Alarms

• Do not face the camera toward any objects with bright lights, including sunshine, bright lamp lights, etc.
• Do not place the camera too close to a place with heavy traffic. Based on our numerous tests, the recommended distance between the camera and the vehicle would be 16 meters (52ft).
• Do not place the camera near outlets, including the air conditioner vents, humidifier outlets, the heat transfer vents of projectors, etc.
• Do not install the camera in places with strong wind.
• Do not face the camera toward a mirror.
• Keep the camera at least 1 meter away from any wireless devices, including WiFi routers and phones in order to avoid wireless interference.

Important Notes on Rechargeable Battery Usage
Reolink Argus Eco is not designed for 24/7 full-capacity running or around- the-clock live streaming. It’s designed to record motion events and remotely view live streaming only when you need it. Learn useful tips on how to extend the battery life in this post:  https://support.reolink.com/hc/en- us/articles/360006991893.

1. Charge the rechargeable battery with a standard and high-quality DC 5V/9V battery charger or Reolink solar panel. Do not charge the battery with solar panels from any other brands.
2. Charge the battery when temperatures are between 0°C and 45°C and always use the battery when temperatures are between -20°C and 60°C.
3. Keep the USB charging port dry, clean, and free of any debris, and cover the USB charging port with the rubber plug when the battery is fully charged.
4. Do not charge, use or store the battery near any ignition sources, such as fires or heaters.
5. Do not disassemble, cut, puncture, short-circuit the battery, or dispose of the battery in water, fire, microwave ovens, and pressure vessels.
6. Do not use the battery if it gives off an odor, generates heat, becomes discolored or deformed, or appears abnormal in any way. If the battery is being used or charged, turn off the power switch or remove the charger immediately, and stop using it.
7. Always follow the local waste and recycle laws when you get rid of the used battery.

Troubleshooting

The camera is not Powering on
If your camera is not powered on, please apply the following solutions:

• Make sure the power switch is turned on.
• Charge the battery with a DC 5V/2A power adapter. When the green light is on, the battery is fully charged.
  If these won’t work, please contact Reolink Support at https://support.reolink.com/.

Failed to Scan the QR Code on the Phone

If the camera cannot scan the QR code on your phone, please try the following solutions:

• Remove the protective film from the camera lens.
• Wipe the camera lens with a dry paper/towel/tissue.
• Vary the distance between your camera and the mobile phone so that the camera can focus better.
• Try to scan the QR code under sufficient lighting.

If these won’t work, please contact Reolink Support at https://support.reolink.com/.

WiFi Connection Failed During Initial Setup Process

If the camera fails to connect to WiFi, please try the following solutions:

• Please make sure the WiFi band is 2.4GHz, the camera does not support 5GHz.
• Ensure that you have entered the correct WiFi password.
• Put the camera closer to your router to ensure a strong WiFi signal.
• Change the encryption method of the WiFi network to WPA2-PSK/WPA-PSK (safer encryption) on your router interface.
• Change your WiFi SSID or password and make sure that SSID is within 31 characters and the password is within 64 characters.
• Set your password using only the characters available on the keyboard.

If these won’t work, please contact Reolink Support at https://support.reolink.com/.

Specifications

Video

• Video Resolution: 1080p HD at 15 frames/sec
• Field of View: 100° diagonal
• Night Vision: Up to 10m (33 ft)

PIR Detection & Alerts

• PIR Detection Distance:
• Adjustable/up to 10m (33 ft)
• PIR Detection Angle: 100° horizontal
• Audio Alert:
• Customized voice-recordable alerts
• Other Alerts:
• Instant email alerts and push notifications

General

• Operating Temperature:
• -10°C to 55°C (14°F to 131°F)
• Weather Resistance:
• IP65 certified weatherproof
• Size: 71 x 186 mm
• Weight (Battery included): 320g (11.2 oz)

Notification of Compliance

FCC Compliance Statement

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For more information, visit https://reolink.com/fcc-compliance-notice/.

CE

• Simplified EU Declaration of Conformity
• Reolink declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.

Correct Disposal of This Product

This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environment-safe recycling.

Limited Warranty

This product comes with a 2-year limited warranty that is valid only if purchased from Reolink Official Store or a Reolink authorized reseller. Learn more:  https://reolink.com/warranty-and-return/.

NOTE: We hope that you enjoy the new purchase. But if you are not satisfied with the product and plan to return it, we strongly suggest that you reset the camera to the factory default settings and take out the inserted SD card before returning.

Terms and Privacy

Use of the product is subject to your agreement to the Terms of Service and Privacy Policy at https://reolink.com. Keep out of reach of children.

End User License Agreement

By using the Product Software that is embedded in the Reolink product, you agree to the terms of this End User License Agreement (“EULA”) between you and Reolink. Learn more: https://reolink.com/eula/.

ISED Radiation Exposure Statement

This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

OPERATING FREQUENCY

• (the maximum transmitted power)
• 2412MHz—2472MHz (18dBm)

References

• ce.com
• Reolink Official: Security Cameras and Systems for Home & Business
• Warranty & Return – Reolink
• Reolink Support - Official Reolink Help Center
• Reolink Support - Official Reolink Help Center
• How to Extend the Battery Life of Reolink Battery Powered Cameras

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>