anslut Ceiling Mount Light Instructions
- June 4, 2024
- anslut
Table of Contents
anslut Ceiling Mount Light
SAFETY INSTRUCTIONS
- It can be only for indoor use.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- Always disconnect from the power supply before installation, connection and service.
- Do not connect the product to the mains while it is still in the pack.
- Check that all connecting cables comply with the applicable regulations and that they are connected correctly.
- Check that the mains voltage corresponds to the rated voltage on the type plate. Incorrect connection can result in a risk of electric shock. The
- electrical installation should be carried out by an authorised electrician.
- Never modify the product, this could result in serious personal injury and will invalidate the warranty.
- Never overload the mains. This can result in fire or a risk of electric shock.
- Keep out of the reach of children.
- Do not store the product in a damp or very cold/hot place to avoid damaging the electronics.
- The electronics in the product are sensitive to knocks and blows.
- Never attempt to replace damaged power cords yourself.
- The product must be discarded if the glass front is cracked.
- The LED light source is not replaceable. When the light source has reached the end of its useful life the complete product must be replaced.
WARNING!
New installations and extensions to existing systems should always be carried
out by an authorised electrician. If you have the necessary experience and
knowledge (otherwise contact an electrician), you can replace power switches
and wall sockets, fit plugs, extension cords and light sockets. Incorrect
installation can result in fatal injury and the risk of fire.
TECHNICAL DATA
- Rated voltage 230 V ~ 50 Hz
- Output 14.5 W
- Luminous flux 1600 Im
- Colour temperature 3000 K
- Life span 30000 h
- Off/On 30 000 times
- Energy class E
- Dimmable Yes
- Safety class II
- Protection rating IP54
- Diffusion angle 120°
- Size \/) 294 x 23 mm
INSTALLATION
| Supplier’s name o rtrademark: | Anslut |
|---|---|
| Supplier’s address (‘): | Jula AB, Julagatan, 2, 53237 Skara, SE |
| Model identifier: | 019942 |
| Type of light source: | |
| lighting technology used: | LED |
light source connected to mains supply or
light source not connected t o mains supply:
| MLS| Connected light source (CLS):| no
Colour-tuneable light source:| no| Envelope:|
High luminance light source:| no| |
Anti-glareshield:| no| Dimmable:| yes
Product parameters
Parameter| Value| Parameter| Value
General product parameters:
Energy consumption in on-mode (kWh/1000 h) I| 15| Energy efficiency
class|
Useful luminous fiux (<!>”), indicating if it refers to the fiux in a sphere
(360°), in a wide cone (120°) or in a narrow cone (90°).| ****
1600 in
Sphere (360°)
| Correlated colour temperature, rounded to the nearest 100 K, or the range of correlated colour temperatures, rounded to the nearest 100 K, that can be set.| ****
3 000
On-mode power (P ), expressed in W
00
| 14,5| Standby power (P,bl’ expressed in Wand rounded to the second decimal.|
0,00
Networked standby power (P,_) for CLS,
expressed in Wand rounded to thesecond decimal.
| | Colour rendering index, rounded to the
nearest integer, or t he range of CR I-values
that can be set.
| ****
80
Outer dimensions without
separatecontrol gear, lighting control parts and non-lighting control parts, if any (millimetre).
| Height| 294| ****
Spectral power distribution in the range 250 nm to 800 nm, at full-load.
| ****
See image in last page
Width| 294
Depth| 23
Claim of equivalent power(‘)| | If yes, equivalent power (W)|
| | Chromaticity coordinates (x and y)| 0,434
0,403
Parameters for directional light sources :
Peak luminous intensity (cd)| Beam angle in degrees, or the range of
beam angles that can be set
|
Parameters for LED and OLED light sources:
R9 colour rendering index value| 0| Survival factor| 0,90
The lumen maintenance factor| 0,96| |
Parameters for LED and OLED mains light sources:
Displacement factor (cos q,71| 0,90| Colour consistency in mcadam ellipses| 6
Claims that an LED light source replaces a fluorescent light source without
integrated ballast of a particular wattage.| ****
_{b)
| ****
If yes then replacement claim (WI
|
Flicker metric (Psi LM)| 1,0| Stroboscopic effect metric (SVMI| 0,4
- (a)”-“: not applicable;
- (b}”-“: not applicable;
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>