ZAVUS Wood Display Installation Guide
- August 31, 2024
- Zavus
Table of Contents
Wood Display
“`html
Product Information
Specifications:
-
Wall Display Type: Wood Display
-
Mounting Compatibility: Drywall and wood-stud wall
construction -
Hardware Included: Wall Bracket, Drywall Anchor, Screws (#8 x
1, #8 x 2) -
Additional Tools Required: Tape Measure, Level,
Pencil/Marking-tool, Drill (3.0mm), Screwdriver -
Special Feature: French-Cleat bracket for easy removal from the
wall
Product Usage Instructions
Installation Steps:
-
Ensure you have the necessary tools and hardware kit
provided. -
Wear Personal Protective Equipment (PPE) including safety
glasses and a dust mask. -
Determine the appropriate location on the wall for mounting the
display. -
Use a tape measure and level to mark the positions for drilling
holes. -
Install the Drywall Anchors using a drill with a 3.0mm
bit. -
Attach the Wall Bracket using the provided screws (#8 x
1). -
If needed, pre-install the medals on the display before hanging
it on the wall. -
Hang the display on the Wall Bracket using the French-Cleat
bracket for easy removal.
Frequently Asked Questions (FAQ)
Q: Can I mount this display on brick or concrete walls?
A: The provided hardware kit is suitable for drywall and
wood-stud walls. For other substrates like brick or concrete, you
will need to source appropriate fasteners separately.
Q: Is it necessary to wear Personal Protective Equipment during
installation?
A: Yes, always wear proper PPE such as safety glasses and a dust
mask to ensure safety during installation.
Q: Can the display be easily removed from the wall once
installed?
A: Yes, the French-Cleat bracket design allows for easy removal
of the display from the wall for medal re-arranging or cleaning
purposes.
“`
Installation Instructions Wood Display
These instructions are for are for typical drywall and wood-stud wall
construction. It will be necessary to source other fasteners if mounting to a
different substrate such as brick, concrete, etc. It is up to the installer to
determine appropriate fasteners for the application. Additional tools may be
required.
Always be sure to wear proper Personal-Protective-Equipment (PPE), such as
safety glasses, dust mask etc.
Hardware Kit Included
Wall Bracket (1)
Drywall Anchor (4)
Screw, #8 x 1″ (3)
Screw, #8 x 2″ (1)
1
Tape Measure
Tool List
Level
Pencil/Marking-tool
Drill
Drill bit, Ø7/32″ (5.5mm) Drill bit, Ø7/64″ #2 Cross head bit or
(3.0mm)
screwdriver
Step 1 Plan location and Hardware · Vertical position is typically set at eye- level. · It is recommended to use at least three fasteners, one at the center and one at each end · For increased strength, align one of the mounting holes with a stud. In this example the center fastener will secured to a stud and the ends with wall anchors.
2
Step 2 Mark Holes · Once the bracket has been located, use a level to ensure
correct bracket orientation and mark holes
Step 3 Drill holes · For anchor holes use drill bit Ø7/32″ (5.5mm). Hole must
pierce completely through drywall. · For holes into a stud, use drill bit
Ø7/64″ (3.0mm). Hole should be approximately 2.0″ deep (50mm)
3
Step 4 Install wall anchors · Gently tap wall anchors into holes ensuring the
top is flush with the outer drywall surface
Step 5 Fasten bracket to wall · Using drill or screwdriver install bracket
with screws. Be sure to use longer screw for stud location and shorter screws
for anchor locations. · Do not over tighten!
4
Step 6 Hang display · As shown in the side-view cross section below, the
display bracket (blue) must sit on top of and behind the wall bracket (green).
The display is now ready for medal installation. Note that it may be easier to
install the medals before hanging the display. The French-Cleat bracket allows
the display to be easily removed from the wall at any time for medal re-
arranging.
5
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>