IMETEC M3901 Steam Iron Instruction Manual

June 10, 2024
IMETEC

IMETEC Logo Operating instructions
ZEROCALC PRO 2300
STEAM IRON
ILLUSTRATIVE GUID
IMETEC M3901 Steam Iron

TECHNICAL DATA

IMETEC M3901 Steam Iron - Air

WARNING: TYPE OF WATER TO BE USED
Use only:

  • demineralised water for iron.

INTRODUCTION

Dear customer, thank you for choosing our product. We feel certain you will appreciate its quality and reliability as it was designed and manufactured with customer satisfaction in mind.These instructions for use comply with the European Standard EN 82079.
WARNING!
Instructions and warnings for a safe use.
Before using this appliance, carefully read the instructions for use and in particular the safety notes and warnings, which must be complied with. Keep this manual together with its illustrative guide for future consultation. Should you transfer the appliance to another user, make sure to hand over this documentation as well.
NOTE: should any part of this manual be difficult to understand or any doubt arise, contact the company at the address indicated on the last page before using the product.
NOTE: partially sighted persons can consult the digital version of these instructions for use on the website www.tenactagroup.com

SAFETY NOTES

  • After removing the appliance from its packaging, verify its integrity based on the drawing and the presence off any damage caused by transport. If in doubt, do not use the appliance and contact an authorised service centre.
    CAUTION! Remove any communication material such as labels, tags etc. from the appliance before use.
    WARNING! Risk of suffocation. Children shall not play with the packaging. Keep the plastic bag out of reach of children.

  • This appliance must be used only for the purpose for which it was designed, namely as a vented steam iron for home use. Any other use is considered not compliant with the intended use and therefore dangerous.

  • This iron is not equipped with a pressure boiler and has been designed to be used for a brief period of time. For this reason it is recommended not to iron for more than an hour.

  • Before connecting the appliance to the mains supply, make sure that the voltage and frequency indicated on the technical data of the appliance correspond to those of the mains supply. These technical data are present on the appliance or on the power supply unit, if any (see illustrative guide).

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
    WARNING! Keep the iron and its cord out of reach of children
    less than 8 years of age when it is energized or cooling down.

  • DO NOT use the appliance with wet hands, damp feet or barefoot.

  • DO NOT pull the supply cord or the appliance itself to remove the plug from the socket.

  • DO NOT expose the appliance to humidity or atmosferic agents (rain, sun, etc.) or extreme temperatures.

  • The appliance must not be left unattended when it is connected to the mains supply.

  • Always disconnect the appliance from the mains supply before cleaning or performing maintenance and when the appliance is not in use.

  • If the appliance is faulty or malfunctions, switch it off and do not tamper with it. Contact an authorised technical service centre for any repairs.

  • If the supply cord is damaged it must be replaced by an authorised technical service centre, so as to prevent all risks.

  • The electrical safety of this appliance is only guaranteed when it is connected correctly to an effective earthing system as required by applicable electrical safety standards. This important safety requirement must be verified before connecting the appliance
    to the mains supply. If in doubt request a thorough check of the system by a qualified technician.

  • DO NOT immerse this appliance into water or other liquids.

  • DO NOT leave this appliance in contact with fabric and surfaces that are easily flammable or can get damaged with heat.

  • This appliance must be used and rested on a flat, stable surface.

  • When placing the iron on its stand, ensure that the surface on which the stand is placed is stable.

  • This appliance is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking water.

  • DO NOT use chemical additives, scented substances or descaling agents.

  • The plug must be removed from the socket-outlet before the water reservoir is filled with water.

  • For the features of the appliance, refer to the external packaging.

  • Use the appliance only with the supplied accessories that are an essential part of the appliance.

SYMBOLS

**** Warning
Hot surface
Prohibited
Note

DESCRIPTION OF THE APPLIANCE AND ITS ACCESSORIES

Refer the illustrative guide on page I to check your appliance’s equipment.

  1. Plate temperature LED
  2. Temperature adjustment knob
  3. Spray button
  4. Super-steam button
  5. Steam selector
  6. Water fill-up opening
  7. Spray
  8. Calc clean button
  9. Max fill-up level Max
  10. Plate with steam holes
  11. Water reservoir
  12.  Technical data
  13. Plug
  14. Water cup

PREPARATION

Sort the laundry according to the international symbols shown on the label; if this is missing, sort according to the type of material.
Start to iron the garments that require a lower temperature so as to reduce idle time (the iron requires less time to warm up than to cool down) and eliminate the risk of burning the fabric.

USE
WARNING! The iron must not be used if it is has been dropped, if there is visible damage or if it leaks water.

WARNING: TYPE OF WATER TO BE USED Use only:

  • demineralised water for iron.

WARNING! Do not pour diluting agents, scented liquids or descaling agents into the reservoir as the use of these substances can damage the product.
WARNING! Do not use water from dryers, air conditioners, water from tumble dryers, filtered water with water softeners and rain water.
The reservoir may contain some water as each product is tested before being put on the market.
Verify that the plug (13) is disconnected from the socket.
Set the steam selector (5) to 0 [Fig. B].
Open the latch (6).
Set the iron in a position that facilitates filling the water and prevents it from overflowing.
Slowly pour the water into the reservoir (11) using the special cup (14) [Fig. C].
Do not exceed the maximum (MAX) level indicated on the reservoir (9).
Close the hatch (6).
SELECTING THE TEMPERATURE
Set the iron upright.
Insert the plug (13) in the socket.
Set the temperature according to the type of fabric in line with the international symbols shown on the labels; using the adjustment knob (2) [Fig. D].
The plate temperature LED (1) indicates that the iron is warming up.
Wait for the plate temperature LED (1) to go off before starting to iron.
Consult the table below to select the correct temperature:

| synthetic fibres e.g. viscose, polyesther
---|---
| silk, wool
| cotton, linen

Fabrics with the following symbols may not be ironed:
synthetic fibres e.g. viscose, polyesther
It is recommended to place a cloth between the iron and the fabric when using the iron for the first time.
Before starting ironing, direct a jet of steam onto the cloth by lifting the iron slightly so that any residual condensation comes out.
ECO FUNCTION
The appliance is equipped with new technology that optimises steam production, thereby reducing energy consumption.
Set the steam selector (5) to ECO to activate the function.
IRONING wITHOUT STEAm (DRY)
Follow the instructions in the “steam ironing” section, leaving the steam selector (5) set to 0.
IRONING WITH STEAM
Select the amount of steam via the steam selector (5).
Move the steam selector (5) to any position between minimum and maximum according to the desired amount.
Continuous steam will only be dispensed when the iron is in a horizontal position.
This stops when the iron is set upright or the steam selector (5) is set to 0.
Steam can only be used at the highest temperatures, as indicated by the symbol on the temperature adjustment knob (2) [Fig. D].
If the selected temperature is too low, water droplets may drip from the plate.
The plate temperature LED (1) flashes intermittently while ironing, thereby indicating that the selected temperature is maintened.
SUPER-STEAm AND VERTICAL STEAm
Press the super-steam button (4) to generate a strong shot of steam that is able to penetrate the fabric and remove the most difficult creases.
Wait a few seconds between each pressing action of the iron [Fig. E].
Press the super-steam button (4) intermittently to iron even in an upright direction (curtains, hung clothes, etc.) [Fig. F].
The super-steam function can only be used at high temperatures. Stop using super-steam button (4) when the plate temperature LED (1) goes on and start ironing again when it goes off.
SPRAY FUNCTION
Verify that there is water in the reservoir (11).
Press the spray button (3) slowly for dense spray or quickly for mist [Fig. G].
Dampen delicate fabric using the spray function or before ironing or alternatively, lay a damp cloth between the fabric an the iron. Do not use the spray function on silk or synthetics.

END OF USE

EMPTYING PROCESS
Disconnect the plug (13) from the socket.
Open the latch (6).
Empty the reservoir (11) by turning the iron upside down and shaking it lightly.
Let the iron cool down completely.
Always set the iron upright.
NOTE: If the appliance is not to be used for several weeks, wait for the appliance to cool down compltely before emptying the water reservoir completely, according to the instructions in the relevant chapter. When the appliance is switched on again, refill the reservoir as indicated in the relevant chapter.

MAINTENANCE

ZERO-CALC ANTI-SCALE SYSTEm
A special resin filter inside the water reservoir decreases the water hardness and limits the formation of limescale in the plate. The resin filter is permanent and cannot be replaced.
SELF CLEAN/CALC-CLEAN SYSTEm
The function allows the internal part of the plate to be cleaned from limescale residue or other impurities.
It is recommended to implement this function every 5 – 10 times it is used.
Fill the water reservoir (11) up to the maximum (MAX) level (9).
Set the steam selector (5) to 0.
Adjust the temperature knob (2) to maximum and wait for the plate temperature control LED (1) to go off.
Disconnect the plug (13) from the socket and immediately place the iron in a horizontal position over a wash basin.
Press the Calc-Clean (8) button until hot water, steam and any impurities or limescale come out of the plate.
Once the iron plate has cooled down (10), clean it with a damp cloth.

CLEANING

WARNING! Make sure the plug of the appliance is disconnected from the socket and the plate has cooled down completely before cleaning the iron.
Any starch deposits or residue on the surface of the plate can be removed with a damp cloth and non-abrasive liquid detergent.
Avoid scratching the plate with steel wool or metal objects.
The plastic parts can be cleaned with a damp cloth and then wiped with a dry cloth.

TROUBLESHOOTING

This chapter describes the most common problems that can arise using the appliance. If the problems cannot be solved with the information below, please contact the Authorised Assistance Centre.

Problem Possible cause Solution
The plate (10) remains cold or does not heat up. There is no power supply.

Verify whether the plug (13) is inserted correctly or try inserting it in another socket.
Check whether the temperature adjustment knob (2) is set to the minimum temperature (Fig. D).
The plate temperature LED (1) goes on and off.| Normal procedure.| The switching ON and OFF of the LED indicates the heating phase of the iron. The LED goes off once the set temperature is reached.
Only a little steam or none at all is dispensed.| The steam selector (5) is set to O.| Set the steam selector (5) to the desired field (Fig. B).
There is not enough water in the reservoir (11).|  Fill the reservoir (11).
The impurities that come out from the steam holes stain the garments.| Possible residue in the steam chamber/plate.| Carry out the Self Clean procedure (see paragraph Seal Clean/CalcClean System).
Chemical additives, scented liquids or descaling agents are being used| These substances damage the product: do not add additives to the water in the reservoir.
Starch is being used.| Always spray the starch on the reverse side of the fabric.
Water leaks from the plate.| The plate temperature is too low due to the super- steam button (4) being pressed too often ,,,?,.| Allow slightly longer intervals between the jets of steam.
The temperature adjustment knob (2) is set to a temperature that is too low (Fig. D).| Turn the temperature adjustment knob (2) to the Max level (Fig. D).

DISPOSAL

**** The product is packaged in recyclable materials. Dispose of it in compliance with the environmental protection standards.
Pursuant to Art. 26 of Italian Legislative Decree no. 49 of 14 March 2014 “Implementation of Directive 2012/19/EU on waste electrical and electronic equipment (WEEE)”, the crossed bin symbol on the appliance or its packaging indicates that the product must be disposed of separately from other waste at the end of its useful life.
The user must therefore take the appliance to an appropriate recycling centre for electrical and electronic equipment.
Alternatively, instead of handling the disposal, the appliance can be handed over to the retailer when a new, equivalent appliance is purchased.
Retailers of electronic products having a sales area of at least 400 m 2 can also be handed electronic products that are to be disposed of measuring less than 25 cm, free of charge and with no obligation to buy.
Appropriate separate collection for the subsequent procedure for the decommissioned appliance for recycling, which includes treatment and environmentally friendly disposal helps prevent adverse effects on the environment and health and promotes reusing and/or recycling materials that the appliance consists of.

ASSISTANCE AND WARRANTY

The appliance is guaranteed for a period of two years from the date of delivery. Evidence shall be taken as the date indicated on the receipt/invoice (provided it is legible), unless the buyer can prove that the delivery occurred later.
In the event of a defect in the product which existed prior to the date of delivery, appliance repair or replacement is guaranteed free of charge, unless one of the two solutions is disproportionate to the other. The buyer has the obligation to notify an authorised Service Centre of the non-conformity within two months from discovering the defect.
The warranty does not cover any part that may be defective due to:
a. transport damage or accidental drops,
b. incorrect installation or an inadequate electrical system,
c. repairs or alterations made by unauthorised personnel,
d. poor or incorrect maintenance and cleaning,
e. product and/or product parts subject to wear and/or consumables,
f. failure to comply with the operating instructions and/or negligent or careless use,
g. the water used is different from that described in the manual,
h. thinner, scented liquids or descaling agents are used,
i. plate damage caused by ironing unsuitable fabrics or with inadequate temperatures for the fabric.
The list above is purely indicative and not exhaustive and in any case, this warranty shall not cover all circumstances that cannot be attributed to manufacturing defects of the appliance.
In addition, the warranty does not cover any case of improper use of the appliance and professional use. All liability is disclaimed for any damage that may directly or indirectly be caused to persons, property and pets as a result of failure to comply with all the  instructions provided in the “Instructions and Warnings Booklet” regarding appliance installation, use and maintenance.
This is without prejudice to any contractual warranty claims against the seller.
Methods of support
Appliance repairs must be carried out by an authorised Service Centre. If the faulty appliance is under warranty, it must be sent to the Service Centre together with a fiscal document that can confirm the date of sale or delivery.

IMETEC Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals