MINGDA Magician X2 3D Printer Direct Extruder Dual Gear Auto Level Instruction Manual

: June 12, 2024
: MINGDA

Table of Contents

Accessories
Assemble
Auto-leveling
Preheat
Insert the filament
Printing
Z-offset adjust
Software Instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Magician X2
Instructions for quick assembly

V1.1

Accessories

MINGDA Magician X2 3D Printer Direct Extruder Dual Gear Auto Level -
Accessories 1

Assemble

Step 1 Install the gantry

MINGDA Magician X2 3D Printer Direct Extruder Dual Gear Auto Level -
Assemble 1

Note: To avoid bending the lead screw and effect the printing model, don’t touch or twist the lead screw when take out the gantry from the package.

Note: The power supply has been adjusted according to the local voltage.
If you need to adjust the voltage, please follow the picture to operate it.

Step 2 Install the fixing plate screw

MINGDA Magician X2 3D Printer Direct Extruder Dual Gear Auto Level -
Assemble 3

Step 3 Install the Filament Holder

MINGDA Magician X2 3D Printer Direct Extruder Dual Gear Auto Level -
Assemble 4

The filament holder can be installed left and right

Step 4 Connect Cable

MINGDA Magician X2 3D Printer Direct Extruder Dual Gear Auto Level -
Assemble 5

Note: If you find there is a little shaking on extruder,bed or X-axis, don’t worry, this is caused by long-term transportation. Please refer to the adjustment video link in the SD card to adjust, it is helpful.

Step 5 Install the Extruder

| |
---|---|---
1.Push the extruder parallel into the support, make sure the screw holes on the top of the extruder are aligned with the screw holes on the
support.| 2.Use M4*10 screws to fix the extruder on the support.| 3.Connect the ribbon cable to the port on the right side of the extruder.

Auto-leveling

MINGDA Magician X2 3D Printer Direct Extruder Dual Gear Auto Level -
leveling 1

Preheat

MINGDA Magician X2 3D Printer Direct Extruder Dual Gear Auto Level -
Preheat

Insert the filament

MINGDA Magician X2 3D Printer Direct Extruder Dual Gear Auto Level - Insert
the filament 1

Printing

MINGDA Magician X2 3D Printer Direct Extruder Dual Gear Auto Level -
Printing 1

Z-offset adjust

MINGDA Magician X2 3D Printer Direct Extruder Dual Gear Auto Level - adjust
1

When you start your first printing, adjust the Babystep value according to the adhesion of the filament and the glass platform. Click “Save” to save your setting, and you don’t need to adjust the value again next time.
[Note: Z-off set use for the first layer only]

| |
---|---|---
If the distance between the nozzle and the platform is too high, the filament will not easy to stick to
the platform. Should click “Decrease” until the distance is proper.| Keep the distance between the nozzle and the hot bed at 0.1mm, the filament will stick to the hot bed evenly| If the distance between the nozzle and the platform is too low, the filament will be not easy to feed out smoothly . Should click “Increase”
until the distance is proper.

Software Instructions

Magician X2 works with a variety of slicing software, such as Cura, Simplify 3D, Repetier-Host, and more. We will introduce CURA_xx.xx in detail, and you will learn how to set the slicing parameters, which will help you become more familiar with the slicing software and print your first model successfully.
First, you can find the CURA_xx.xx from the SD card, and install it on your computer.

Install CURA