CANDY CCE160X Built in Hood User Manual

INSTALLATION AND USER’S MANUAL

INTRODUCTION

Thank you for choosing this cooker hood.
This instruction manual is designed to provide you with all required instructions related to the installation, use, and maintenance of the appliance.
In order to operate the unit correctly and safely, please read this instruction manual carefully before installation and usage.
The cooker hood uses high-quality materials and is made with a streamlined design. Equipped with a large power electric motor and centrifugal fan, it also provides strong suction power, low noise operation, a non-stick grease filter, and easy assembly installation.

SAFETY PRECAUTION

Never let the children operate the machine.
The cooker hood is for home use only, not suitable for barbecue, roast shop, and other commercial purpose.
The cooker hood and its filter should be cleaned regularly in order to keep them in good working condition.
Clean the cooker hood according to the instruction manual and keep the unit from the danger of burning.
Forbid the direct baking from the gas cooker.
Please keep the kitchen room good convection.
Before connecting this appliance check that the power supply cord is not damaged. A damaged supply cord must be replaced by qualified service personnel only.
There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels; the air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels;
Regulations concerning the discharge of air have to be fulfilled.
This appliance is not intended for use by persons(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person slide for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not flambé under the range hood.
CAUTION: Accessible parts may become hot when used with a cooking appliance
– These shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels(not applicable to appliances that only discharge the air back into the room);
– the details concerning the method and frequency of cleaning.
– there is a fire risk if cleaning is not carried out in accordance with the instructions; – do not flame under the range hood;
– CAUTION: Accessible parts may become hot when used with cooking appliances.

Electrical Shock Hazard
Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably qualified engineer.
Failure to follow these instructions can result in death, fire, or electrical shock.

The lamp used in this product is not suitable for use in the lighting of a room.
The purpose of this lamp is to provide illumination for using the product.

Direct Connection

The appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3mm between the contacts.
The installer must ensure that the correct electrical connection has been made and that it complies with the wiring diagram.
The cable must not be bent or compressed.
Regularly check the power plug and power cord for damage. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
Electrical Installation
All installations must be carried out by a competent person or qualified electrician. Before connecting the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate.

WARNING: This is a Class I appliance and MUST be earthed
This appliance is supplied with a 3-core mains cable colored as follows:
Brown = L or Live
Blue = N or Neutral
Green and Yellow = E or Earth

The fuse must be rated at 3 Amps.

Standard Installation Accessories List

φ8 rawl plugs
φ8×φ6 white color| | 9
Screws
ST4.0×30| | 9
φ7.2screws
ST4.0×8| | 2

INSTALLATION （wall mounting）

If you have an outlet to the outside, your cooker hood can be connected as below picture by means of an extraction duct (enamel, aluminum, flexible pipe or inflammable material with an interior diameter of 150mm)

1. Before installation, turn the unit off and unplug it from the outlet.

2. The cooker hood should be placed at a distance of 65~75cm above the cooking plane for the best effect.

3. Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten the bracket onto the wall with the screws provided. For the inclined panel, the Model
   needs to drill 2x8mm extra holes & fixing screws & screw plugs before installation. Voor schuine modellen

4. Leave up the cooker hood and hang it onto the wall bracket hook.

5. Fix the one-way valve to the air outlet of the cooker hood. Then, attached the exhaust pipe to the one-way-valve as shown below.

i. Place the glass in the appropriate position on the top of the cooker hood.
ii. Fix with 4 screws and a washer. In order to avoid the glass cracking, please do not tighten the screws too strongly.
i. By Putting the inner chimney into the outer chimney. Then pulling out the inner chimney upwards. Adjust to reach the height required. ii. Sliding the chimney to adjust the chimney height. When the height you required is reached, then hang the fixing hole to the fixing screws as shown in the below pictures.

i. Drill 2 x 8mm holes to accommodate plate II. Screw and tighten the plate II onto the wall with 2 screws provided.
ii. Assembly the chimney onto the unit and fix it with 2 screws.

Standard Installation Accessories List

φ8 rawl plugs
φ8×φ6whitecolor| | 2
Screws
ST4.0×30| | 2
Screws
ST3.5×12| | 2

INSTALLATION(AIR DEFLECTOR FOR T-SHAPE, CURVED GLASS,FLAT GLASS MODELS):
Air deflector is mentioned as included and not optional.

1. Before installation, curve both ends of the bracket as shown below:
2. Fix the bracket to the T-shaped plastic outlet with 2pcs ST3.5x12mm screws provided.
3. Drill 2 holes to accommodate the wall plugs, then screw and tighten the bracket onto the wall with 2pcs ST4x30mm screws provided.
4. Attach the exhaust pipe onto the air outlet of the cooker hood as shown below:
5. Install the chimney to the unit and fix it.

o “Please kindly be noted: T-shaped plastic outlet and v-flaps can not be used datthesame time. You can use the mint woways:1)Add-flaponexistingo outlet; 2) Use T-shaped plastic outlet, no add v-flap.”
o “Note: The product is provided with a v-flap accessory. This accessory is not mandatory for installation, operation, and use of the product.”

Standard Installation Accessories List

φ8rawlplugs
φ8×φ6whitecolor| | 2
Screws
ST4.0×30| | 2
Screws
ST3.5×12| | 2

INSTALLATION（AIR DEFLECTOR FOR PYRAMID & SLANT MODELS):
Air deflector is mentioned as included and not optional.

1. Fix the bracket to the T-shaped plastic outlet with 2pcs ST3.5x12mm screws provided as shown below:
2. Drill 2 holes on the wall to accommodate the wall plugs, then screw and tighten the bracket onto the wall with 2pcs ST4x30mm screws provided.
3. Attach the exhaust pipe onto the air outlet of the cooker hood as shown below:
4. Install the chimney to the unit and fix it.

o “Please kindly be noted: T-shaped plastic outlet and v-flaps can not be used datthesame time. You can use mint woways:1)Add-flaponexistingo outlet; 2) Use T-shaped plastic outlet, no add v-flap.”
o “Note: The product is provided with a v-flap accessory. This accessory is not mandatory for installation, operation, and use of the product.”

INSTALLATION (VENT INSIDE)

If you do not have an outlet to the outside, the exhaust pipe is not required and the installation is similar to the one shown in the section “INSTALLATION (VENT OUTSIDE)”.

An activated carbon filter can be used to trap odors.
In order to install the activated carbon filter, the grease filter should be detached first. Press the lock and pull it downward.

Plug the activated carbon filter into the unit and turn it in a clockwise direction.
Repeat the same on the other side.

NOTE:

• Make sure the filter is securely locked. Otherwise, it would loosen and cause danger.
• When the activated carbon filter is attached, the suction power will be lower

DESCRIPTION OF COMPONENTS

CONFIGURATION 1

OPERATION
Button 1
The button is with indicating backlit, when you press the button, the backlit will be turned on and the fan will be turned on at low speed. when pressed again, it will turn off the fan.
It’s used for Ventilation in the kitchen. It is suitable for simmering and cooking which does not make much steam.
Button 2
The button is with indicating backlit, when you press the button, the backlit will be turned on and the fan will be turned on at Medium Speed. when pressed again, it will turn off the fan.
Airflow speed is ideal for ventilation in standard cooking operations.
Button 3
The button is with indicating backlit, when you press the button, the backlit will be turned on and the fan will be turned on at High Speed. when pressing again,. it will turn off the fan.
When a high density of smoke or steam is produced, press the high-speed button for the highest effective ventilation.
NOTE: If Low / Medium / High-speed buttons are pressed at the same time, the unit will only operate at the highest speed.
Light button

CONFIGURATION 2

OPERATION
Off button
It’s used for turning off the fan.
Low-Speed button 1
It’s used for Ventilation in the kitchen. It is suitable for simmering and cooking which does not make much steam.
Medium Speed button 2
Airflow speed is ideal for ventilation in standard cooking operations.
High-Speed button 3
When a high density of smoke or steam is produced, press the high-speed button for the highest effective ventilation.
NOTE: If Low / Medium / High-speed buttons are pressed at the same time, the unit will only operate at the highest speed.
Light button

CONFIGURATION 3

On/Off button
It’s used for turning on/off the fan.
Speed plus button
For increasing the speed of the fan
Speed decrease button
For decreasing the speed of the fan.
Light button
Digital display
Fan speed display:”1″ for Low speed, “2” for Medium speed, “3” for High speed, “4” for Booster function.
Quick timer: Press & hold for 1 second, Digital display will flash & into 5 minutes count down, and after 5 minutes motor & light will turn off automatically & Buzzer sound for 1 second.
Booster function
This hood has a booster function. To activate the booster, Press to speed 4, enter into highest speed while the hood is in use and it will increase speed for 5 minutes, before slowing down again.

MAINTENANCE

Before cleaning switch the unit off and pull out the plug.
I. Regular Cleaning
Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material, or stiff brushes to clean the unit.
II. Monthly Cleaning for Grease Filter
ESSENTIAL: Clean the filter every month can prevent any risk of fire.
The filter collects grease, smoke, and dust…… so the filter is directly affecting the efficiency of the cooker hood. If not cleaned, the grease residue (potentially flammable) will saturate the filter. Clean it with household cleaning detergent.
III. Annual Cleaning for Activated Carbon Filter
Apply SOLELY to a unit that is installed as a recirculation unit (not vented to the outside). This filter traps odors and must be replaced at least once a year depending on how frequently the cooker hood is used.
IV. Changing a light bulb
Remove the screws on the glass, and take off the hood glass. Find the bulb that requires replacement, you will find it located in the light fixture which is inside the exposed section of the canopy.

Disconnect the light wiring point and remove the bulb holders and wiring from the hood. Important: It’s not possible to replace the bulbs individually, it will be necessary to obtain the bulbs, bulb holders, and wiring as a complete part. (LED light: MAX 1.5W) Fit the replacement bulbs, bulb holders, and wiring in the same manner as the originals. Then reconnect the light wiring point.

Refit the hood glass and fasten the glass screws. Make sure the screws are fully tightened.

TROUBLESHOOTING

Light on, but the fan does not
work| The fan blade is jammed.| Switch off the unit and repair it by qualified service personnel only.
The motor is damaged.
Both light and fan do not work| Halogen light bulb burn.| Replace the bulb with the correct rating.
Power cord loses.| Plug into the power supply again.
Serious Vibration of the unit| The fan blade is damaged.| Switch of the unit and repair by qualified service personnel only.
The fan motor is not fixed tightly.| Switch off the unit and repair it by qualified service personnel only.
The unit is not hung properly on the bracket.| Take down the unit and check whether the bracket is in the proper
location.
Suction performance is not good| Too long distance between the unit and the cooking plane| Readjust the distance to 65-75cm

CUSTOMER ASSISTANCE SERVICE

If you cannot identify the cause of the operating anomaly, switch off the appliance and contact the Assistance Service.
PRODUCT SERIAL NUMBER. Where can I find it?
It is important for you to inform the Assistance Service of your product code and its serial number (a 16-character code that begins with the number 3); this can be found on the guarantee certificate or on the data plate located on the appliance.
It will help to avoid wasted journeys to technicians, thereby (and most significantly) saving the corresponding callout charges.

ENVIRONMENTAL PROTECTION

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
The symbol on the product indicates that this product may not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about the treatment, recovery, and recycling of this product, please contact your local city office, your household waste disposal service, or the shop where you purchased the product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>