dji MT3PD Aircraft Mini 3 User Guide

: June 10, 2024
: DJi

Table of Contents

Download the DJI Fly App and watch the tutorial videos
Specifications
Compliance Info
Environmentally friendly disposal
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

dji MT3PD Aircraft Mini 3 User Guide

Aircraft

Gimbal Camera
Infrared Sensing System
Downward Vision System
Antennas
Front LEDs
Battery Buckles
Power Button and Battery Level LEDs
USB-C Port
microSD Card Slot

Remote Controller RM330

Control Sticks
Flight Pause/Return to Home (RTH) Button
Flight Mode Switch
Power Button
Battery Level LEDs
Record Button
Gimbal Dial
Shutter Button
Zoom Dial
Control Sticks Storage Slot
Customizable Buttons
4G Dongle Port（USB-C）
microSD Card Slot
Power Connector（USB-C）

Download the DJI Fly App and watch the tutorial videos

App Using

Charge to activate

Check Battery Level, Power on/off

Check battery level: press once.
Power on/off: press then press and hold.

Prepare the aircraft

Prepare the remote controller

Ready to fly
Power on the remote controller and the aircraft, then launch the DJI Fly App.

Fly
Auto take-off/land: Touch and hold the following icon from DJI Fly App to take off or land.

Manually take-off/land:
Start/stop the motors:

Take off: Slowly push the throttle stick up.

Land: Slowly push the throttle stick down until the aircraft lands on ground. Hold the stick down until the motors stop.

Flight control

Specifications

Aircraft (MT3PD)

Operating Temperature| -10° to 40° C (14° to 104° F)
O2
Operating Frequency| 2.4000-2.4835 GHz, 5.725-5.850 GHz
Transmitter Power (EIRP)| 2.4 GHz: <26 dBm (FCC), <20 dBm (CE/SRRC/MIC)5.8 GHz: <26 dBm (FCC/SRRC), <14 dBm (CE)
Wi-Fi
Protocol| 802.11a/b/g/n/ac
Operating Frequency| 2.4000-2.4835 GHz, 5.725-5.850 GHz
Transmitter Power (EIRP)| 2.4 GHz: <19 dBm (FCC/CE/SRRC/MIC)5.8 GHz: <20 dBm (FCC/SRRC), <14 dBm (CE)
Bluetooth 5.2
Operating Frequency| 2.4000-2.4835 GHz
Transmitter Power (EIRP)| < 8 dBm
Remote Controller (Model: RM330)
Operating Temperature| -10° to 40° C (14° to 104° F)
O2
Operating Frequency| 2.4000-2.4835 GHz, 5.725-5.850 GHz
---|---
Transmitter Power (EIRP)| 2.4 GHz: <26 dBm (FCC), <20 dBm (CE/SRRC/MIC)5.8 GHz: <26 dBm (FCC) , <14 dBm (CE), <23 dBm (SRRC)
Wi-Fi
Protocol| 802.11a/b/g/n
Operating Frequency| 2.4000-2.4835 GHz, 5.150-5.250 GHz, 5.725-5.850 GHz
Transmitter Power (EIRP)| 2.4 GHz: <23 dBm (FCC), <20 dBm (CE/SRRC/MIC)5.1 GHz: <23 dBm (FCC/CE/SRRC/MIC)5.8 GHz: <23 dBm (FCC/SRRC), <14 dBm (CE)
Bluetooth 4.2
Operating Frequency| 2.4000-2.4835 GHz
Transmitter Power (EIRP)| <8 dBm
Intelligent Flight Battery (BWX162-2453-7.38)
Charging Temperature| 5° to 40° C (41° to 104° F)
Capacity| 2453 mAh
Battery Type| Li-ion
Chemical System| LiNiMnCoO2
Max Charging Power| 37 W
Standard Voltage| 7.38 V
Support Charger| DJI 30W USB-C ChargerOr other USB Power Delivery charger

Compliance Info

FCC Compliance Notice
Supplier’s Declaration of Conformity
Product name: DJI MINI 3
Model Number: MT3PD
Responsible Party: DJI Technology, Inc.
Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
Website: www.dji.com

We, DJI Technology, Inc., being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information
The aircraft complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. This transmitter must not be co- located or operating in conjunction with any other antenna or transmitter.

This remote controller complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

ISED Compliance Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device

This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating inconjunction with any other antenna or transmitter

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.

These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

Indoor use Only

EU Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI MINI 3) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available online at www.dji.com/euro- compliance EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany
GB Compliance Statement: SZ DJI TECHNOLOGY CO., LTD. hereby declares that this device (DJI MINI 3) is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017. A copy of the GB Declaration of Conformity is available online at www.dji.com/euro- compliance

Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.