VIZULO Stork Little Sister Extended LED Street Luminaire Instruction Manual
- May 15, 2024
- VIZULO
Table of Contents
VIZULO Stork Little Sister Extended LED Street Luminaire
Product Information
Specifications:
- Product Name: VIZULO Stork Little Sister Extended LED street luminaire
- Model Number: Not specified
- Certifications: 05 IEC IP66 IK09 EN 60598
- Voltage: 2200 – 240 V AC
Product Usage Instructions
LED Module Replacement:
- Turn the luminaire over.
- Unscrew the glass from the body and lift it.
- Take a reference photo of wiring if necessary.
- Disconnect the PCB module from the driver.
- Unscrew the PCB module, replace it with a new one, and screw it back into place.
- Connect the PCB module to the driver.
- Lower the glass and screw it back.
LED Driver Replacement:
- Open the latches.
- Lift the lid of the luminaire.
- Make a reference picture of the wiring.
- Unscrew the EQUI wire.
- Disconnect the wires from the driver.
- Unscrew the LED driver.
- Replace the LED driver and screw it back into place.
- Screw in the EQUI wire and the driver.
- Connect the wires to the driver.
- Lower the lid of the luminaire.
- Close the latches.
Terms of Use and Maintenance:
Before luminaire is turned on, it should be mounted according to this mounting
instruction or any other applicable regulations. Any actions with the
luminaire must be performed by a qualified person, who is certified according
to national regulations and requirements. To prevent any accidents, the person
installing the luminaire must follow national safety requirements and
instructions.
FAQ:
-
Q: Is it safe to replace the LED module or driver myself?
A: It is recommended that any replacements or maintenance be performed by a qualified person certified according to national regulations for safety reasons. -
Q: What should I do if I encounter difficulties during the replacement process?
A: If you face any challenges or uncertainties during the replacement process, it is advisable to seek professional assistance to avoid any risks or damage to the luminaire.
FEATURE
PCB module replacement
Danger
Before disassembling the luminaire, check if it is disconnected from the power
grid.
- Turn the luminaire over.
- Unscrew the glass from the body and lift it.
- Take a reference photo of wiring if necessary.
- Disconnect the PCB module from the driver.
- Unscrew the PCB module, replace it with a new one and screw it back into place.
- Connect the PCB module to the driver.
- Lower the glass and screw it.
- Turn the luminaire over.
LED driver replacement
Danger!
Before disassembling the luminaire, check if it is disconnected from the power
grid.
- Open the latches.
- Lift the lid of the luminaire.
- Make a reference picture of the wiring.
- Unscrew the EQUI wire.
- Disconnect the wires from the driver.
- Unscrew the LED driver.
- Unscrew the LED driver, replace it and screw it back into place.
- Screw in the EQUI wire and the driver.
- Consult the reference picture.
- Connect the wires to the driver.
- Lower the lid of the luminaire.
- Close the latches.
Terms of use and maintenance
Before luminaire is turned on, it should be mounted according with this mounting instruction or any other applicable regulations.
Mounting instructions
Mounting of luminaire must be performed by a qualified person according with
following instructions:
- The warranty of luminaire does not apply, if the mounting of luminaire has been performed in precipitation (rain, snow, hail).
- The warranty of luminaire does not apply, if a control system unauthorized by VIZULO or an inapplicable LED driver has been used to drive the luminaire.
- The warranty of luminaire does not apply, if it has been used in an unsuitable ambient temperature or has been supplied by voltage outside of the specified range.
- The warranty of luminaire does not apply, if the LED driver program has been changed in any way.
- The warranty of the luminaire does not apply, if the logged history data of the LED driver has been deleted without the permission of VIZULO.
- The warranty of luminaire does not apply, if it has been mounted in unspecified angles or upside down (luminaire glass directed up), or it has been completely submerged under water.
Safety instructions
Any actions with the luminaire must be performed by a qualified person, who is
certified according with national regulations and requirements.
To prevent any accidents person installing the luminaire must follow national
safety requirements and following instructions:
- The label containing technical parameters of the luminaire has to be studied before the work on it has begun.
- Any luminaire build or design changes are prohibited.
- The luminaire must be used in good technical condition and according with this instruction.
- Only VIZULO authorized spare parts and accessories can be used to repair the luminaire.
- The repair of luminaire has to be performed by a qualified and certified person.
Maintenance and repair
Luminaire has to be disconnected from electrical grid before it is opened
and/or repaired!
- The person working with the luminaire must follow national regulations and legislations that apply to maintenance and testing of electrical or electronic appliances.
- The luminaire may need to be cleaned depending on its environment. Only a damp cloth or a sponge may be used to clean the luminaire. Use only household detergents diluted by water.
- Only VIZULO-authorized spare parts may be used for the luminaire.
- Instruction for changing spare parts must be requested from VIZULO and studied before the repair is attempted.
- LED modules, lens and LED drivers can be changed on an installed luminaire, but it is advised to perform this task indoor to avoid water entering the luminaire.
- Spare parts (lens, LED modules and drivers) should be ordered from the information available on the luminaire label.
06-07-2023
SIA VIZULO
Laucu Lejas, Iecava, Latvia, LV-3913
www.vizulo.com