RISCO RP432KPP2 LCD Panda Keypad User Guide
- June 10, 2024
- RISCO
Table of Contents
- Introduction
- Installation
- Keypad PCB
- Configuration
- Keypad Keys
- Keypad Settings
- Proximity Tag Operation
- Automatic Upgrade Resulting from Panel Manual Upgrade
- Cleaning the Keypad
- Technical Specification
- Ordering Information
- UKCA and CE RED Compliance Statement
- Standard Limited Product Warranty (“Limited Warranty”)
- Contacting RISCO Group
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
RISCO RP432KPP2 LCD Panda Keypad User Guide
Introduction
The user-friendly wired LCD & Proximity keypad enables simple operation and programming of the LightSYS (version 5.63 and above) and ProSYS Plus (version 1.2 and above) security systems, and for the CS (Version 3.1.0.0003).
Main Features
- Optional built-in proximity tag reader
- Wall mounting by screws
- Wall tamper protection
- Modern look and feel
- Simple to install with incorporated mounting bracket
Installation
Mounting the Keypad
Mount the keypad on the wall using the supplied mounting bracket. To mount the keypad:
-
Separate the mounting bracket from the keypad (see Figure 1).
-
Insert the wires through the hole in the mounting bracket (see Figure 2).
-
Use the mounting holes as a template and secure the mounting bracket to the wall using 4 screws and 1 extra screw for the tamper (see Figure 3). * Used for tamper
-
Connect the wires to the (AUX, COM and BUS) connector shown in Figure7.
-
Mount the keypad to the mounting bracket (see Figure 4).
-
Insert the fastening screw to lock the keypad (see Figure 5).
Mounting on Gang Box (Optional):
-
Repeat steps 1 to 2 in the previous procedure.
-
Secure the mounting bracket to the Gang Box using the two screws as illustrated in Figure 6.
-
Mount the keypad to the mounting bracket and insert the fastening screw to lock the keypad
Keypad PCB
Use DIP switches 1 to 5 to define the BUS ID of each accessory / detector
according to the table in Figure 7.
Configuration
Visual Indicators
The following visual indicators are displayed on the LCD panel:
Icon|
Indication
|
Operation
---|---|---
Trouble
| On| System trouble
Off| System is operating normally
| On| System is ready to be armed
Off| System is not ready to be armed
Slow Flash| System is ready to be armed while exit/entry zone is open
Arm/Alarm
| On| System is armed in Full Arm or Stay Arm mode
Off| System is disarmed
Slow Flash| System is in Exit Delay
Rapid Flash| Alarm condition
Stay / Bypass
| On| System is Stay Arm mode (Part Set) or Zone Bypass mode
Off| No bypass zones in the system
Tamper
| On| Zone/keypad/external module has been tampered
Off| All zones are operating normally
Cloud Connectivity
| On| System connected to cloud
Slow Flash| Cloud connectivity trouble
Off| No cloud connection configured / No cloud connectivity
Keypad Keys
Control Keys
Key | Operation |
---|---|
**** | In Normal Operation mode: Used for Away (Full setting). |
In User Functions menu: Used to change data.
| In Normal Operation mode: Used for Stay arming (Part Setting).
In User Functions menu: Used to change data.
| Used to disarm (unset) the system after a user code is entered; is used
to terminate commands and confirm data to be stored.
| Used to scroll up a list or to move the cursor to
the left;i Provides the system status.
| Used to scroll down a list or to move the cursor to the right.
| In Normal Operation mode: Used to enter the User Functions menu.
In User Functions menu: Used to move back one step in the menu.
Emergency Keys
The following operations will send emergency notifications to the alarm monitoring station
Key | Operation |
---|---|
Pressing both keys simultaneously for at least two seconds activates a Fire |
alarm
| Pressing both keys simultaneously for at least two seconds activates an
Emergency alarm
| Pressing both keys simultaneously for at least two seconds activates a
Police (Panic) alarm
Function Keys
Key | Operation |
---|---|
Used to arm (set) groups of zones (by default) or to activate a prerecorded |
series of commands (macros).To activate press for 2 seconds
| Numerical keys that are used to input numeric codes (arming, disarming or
used to activate specific functions)
Keypad Settings
Note: The following settings must be defined individually for each keypad connected to the system
To define keypad settings when idle follow this procedure:
- Press for two seconds until the Keypad Settings menu appears
- Select the relevant icon using the keys:
| Brightness
---|---
| Contrast
| Keypad’s buzzer volume - Press .
- Press the keys to adjust the level settings.
- Press to save the adjustment.
- Press to exit the keypad settings
Proximity Tag Operation
Present the Proximity Tag to the keypad (after waking the keypad) as shown in the following illustrations:
Automatic Upgrade Resulting from Panel Manual Upgrade
Upon initiation of the LightSYS2 panel remote upgrade (See LightSYS2 Installer Manual, Appendix I: Remote Software Upgrade), the keypad software may automatically also be upgraded. During this approximately three-minute process upgrade icons ( ) and the power icon ( ) are displayed on the keypad and the LED light flashes. Do not disconnect during this period.
Cleaning the Keypad
Use a non-abrasive damp cloth to clean the keypad. Do not expose the screen or the keys directly to liquid.
Technical Specification
Parameter | Description |
---|---|
Current Consumption: RP432KPP2RP432KP02 | **** 13.8v +/-10%, 130 mA |
typical/180 mA max.
Main Panel Connection| 4-wire BUS, up to 300 m (1000 ft) from Main Panel
Proximity RF frequency:| 13.56 MHz
Dimensions (H x W x D):| 178 x 103 x 27 mm (7 x 4.1 x1.1″)
Weight:| RP432KPP2: 295 gr.RP432KP02: 287 gr.
Operating temperature:| -10°C to 55°C (14°F to 131°F)
Storage temperature:| -20°C to 60°C (-4°F to 140°F)
Humidity Range| Average relative humidity: 75%
Standard Compliance| EN50131-3 Grade 2 Environmental Class II
Min. number of variations of PIN codes| 10000 for 4-digit codes
Number of invalid code entries before user interface is disabled| After 3
attempts
Ordering Information
Model | Description |
---|---|
RP432KPP2 | Panda Wired LCD Keypad, Proximity |
RP432KP02 | Panda Wired LCD Keypad |
UKCA and CE RED Compliance Statement
Hereby, RISCO Group declares that this equipment is in compliance with the essential requirements of the UKCA Radio Equipment Regulations 2017 and CE Directive 2014/53/EU. For the UKCA and CE Declaration of Conformity please refer to our website: www.riscogroup.com
Standard Limited Product Warranty (“Limited Warranty”)
RISCO Ltd. (“RISCO”) guarantee RISCO’s hardware products (“Products”) to be
free from defects in materials and workmanship when used and stored under
normal conditions and in accordance with the instructions for use supplied by
RISCO, for a period of (i) 24 months from the date of delivery of the Product
(the “Warranty Period”). This Limited Warranty covers the Product only within
the country where the Product was originally purchased and only covers
Products purchased as new. Contact with customers only. This Limited Warranty
is solely for the benefit of customers who purchased the Products directly
from RISCO or from an authorized distributor of RISCO. RISCO does not warrant
the Product to consumers and nothing in this Warranty obligates RISCO to
accept Product returns directly from end users who purchased the Products for
their own use from RISCO’s customer or from any installer of RISCO, or
otherwise provide warranty or other services to any such end user directly.
RISCO’s authorized distributor or installer shall handle all interactions with
its end users in connection with this Limited Warranty. RISCO’s authorized
distributor or installer shall make no warranties, representations, guarantees
or statements to its end users or other third parties that suggest that RISCO
has any warranty or service obligation to, or any contractual privy with, any
recipient of a Product. Remedies. In the event that a material defect in a
Product is discovered and reported to RISCO during the Warranty Period, RISCO
shall accept return of the defective Product in accordance with the below RMA
procedure and, at its option, either (i) repair or have repaired the
defective Product, or (ii) provide a replacement product to the customer
Return Material Authorization. In the event that you need to return your
Product for repair or replacement, RISCO will provide you with a Return
Merchandise Authorization Number (RMA#) as well as return instructions. Do not
return your Product without prior approval from RISCO. Any Product returned
without a valid, unique RMA# will be refused and returned to the sender at
the sender’s expense. The returned Product must be accompanied with a detailed
description of the defect discovered (“Defect Description”) and must otherwise
follow RISCO’s then-current RMA procedure published in RISCO’s website at
www.riscogroup.com in connection with any such
return. If RISCOdetermines in its reasonable discretion that any Product
returned by customer conforms to the applicable warranty (“Non-Defective
Product”), RISCO will notify the customer of such determination and will
return the applicable Product to customer at customer’s expense. In addition,
RISCO may propose and assess customer a charge for testing and examination of
Non-Defective Product. Entire Liability. The repair or replacement of Products
in accordance with this Limited Warranty shall be RISCO’s entire liability and
customer’s sole and exclusive remedy in case a material defect in a Product is
discovered and reported as required herein. RISCO’s obligation and this
Limited Warranty are contingent upon the full payment by customer for such
Product and upon a proven weekly testing and examination of the Product
functionality.
Limitations. This Limited Warranty is the only warranty made by RISCO
with respect to the Products. The warranty is not transferable to any third
party. To the maximum extent permitted by applicable law, this Limited
Warranty shall not apply and will be void if: (i) the conditions set forth
above are not met (including, but not limited to, full payment by customer for
the Product and a proven weekly testing and examination of the Product
functionality); (ii) if the Products or any part or component thereof: (a)
have been subjected to improper operation or installation; (b) have been
subject to neglect, abuse, willful damage, abnormal working conditions,
failure to follow RISCO’s instructions (whether oral or in writing); (c) have
been misused, altered, modified or repaired without RISCO’s written approval
or combined with, or installed on products, or equipment of the customer or of
any third party; (d) have been damaged by any factor beyond RISCO’s reasonable
control such as, but not limited to, power failure, electric power surges, or
unsuitable third party components and the interaction of software therewith or
(e) any failure or delay in the performance of the Product attributable to any
means of communication provided by any third party service provider,
including, but not limited to, GSM interruptions, lack of or internet outage
and/or telephony failure. BATTERIES ARE EXPLICITLY EXCLUDED FROM THE
WARRANTY AND RISCO SHALL NOT BE HELD RESPONSIBLE OR LIABLE IN RELATION
THERETO, AND THE ONLY WARRANTY APPLICABLE THERETO, IF ANY, IS THE BATTERY
MANUFACTURER’S WARRANTY. RISCO does not install or integrate the Product in
the end user’s security system and is therefore not responsible for and cannot
guarantee the performance of the end user’s security system which uses the
Product or which the Product is a component of. This Limited Warranty applies
only to Products manufactured by or for RISCO. Further, this Limited Warranty
does not apply to any software (including operating system) added to
orprovided with the Products or any third-party software, even if packaged or
sold with the RISCO Product. Manufacturers, suppliers, or third parties other
than RISCO may provide their own warranties, but RISCO, to the extent
permitted by law and except as otherwise specifically set forth herein,
provides its Products “AS IS”. Software and applications distributed or made
available by RISCO in conjunction with the Product (with or without the RISCO
brand), including, but not limited to system software, as well as P2P services
or any other service made available by RISCO in relation to the Product, are
not covered under this Limited Warranty. Refer to the Terms of Service at:
www.riscogroup.com/warranty for details
of your rights and obligations with respect to the use of such applications,
software or any service. RISCO does not represent that the Product may not be
compromised or circumvented; that the Product will prevent any personal injury
or property loss by burglary, robbery, fire or otherwise, or that the Product
will in all cases provide adequate warning or protection. A properly installed
and maintained alarm may only reduce the risk of a burglary, robbery or fire
without warning, but it is not insurance or a guarantee that such will not
occur or will not cause or lead to personal injury or property loss.
CONSEQUENTLY, RISCO SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY,
PROPERTY DAMAGE OR OTHER LOSS BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM
THAT THE PRODUCT FAILED TO GIVE WARNING. EXCEPT FOR THE WARRANTIES SET
FORTH HEREIN, RISCO AND ITS LICENSORS HEREBY DISCLAIM ALL EXPRESS, IMPLIED
OR STATUTORY, REPRESENTATIONS, WARRANTIES, GUARANTEES, AND CONDITIONS WITH
REGARD TO THE PRODUCTS, INCLUDING BUT NOT LIMITED TO ANY REPRESENTATIONS,
WARRANTIES, GUARANTEES, AND CONDITIONS OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, TITLE AND WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS,
TO THE EXTENT PERMITTED BY LAW. WITHOUT LIMITING THE GENERALITY OF THE
FOREGOING, RISCO AND ITS LICENSORS DO NOT REPRESENT OR WARRANT THAT: (I)
THE OPERATION OR USE OF THE PRODUCT WILL BE TIMELY, SECURE, UNINTERRUPTED
OR ERROR-FREE; (ii) THAT ANY FILES, CONTENT OR INFORMATION OF ANY KIND
THAT MAY BE ACCESSED THROUGH THE PRODUCT SHALL REMAIN SECURED OR NON
DAMAGED. CUSTOMER ACKNOWLEDGES THAT NEITHER RISCO NOR ITS LICENSORS
CONTROL THE TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING THE
INTERNET, GSM OR OTHER MEANS OF COMMUNICATIONS AND THAT RISCO’S PRODUCTS,
MAY BE SUBJECT TO LIMITATIONS, DELAYS, AND OTHER PROBLEMS INHERENT IN THE
USE OF SUCH MEANS OF COMMUNICATIONS. RISCO IS NOT RESPONSIBLE FOR ANY
DELAYS, DELIVERY FAILURES, OR OTHER DAMAGE RESULTING FROM SUCH PROBLEMS.
RISCO WARRANTS THAT ITS PRODUCTS DO NOT, TO THE BEST OF ITS KNOWLEDGE,
INFRINGE UPON ANY PATENT, COPYRIGHT, TRADEMARK, TRADE SECRET OR OTHER
INTELLECTUAL PROPERTY RIGHT IN ANY EVENT RISCO SHALL NOT BE LIABLE FOR ANY
AMOUNTS REPRESENTING LOST REVENUES OR PROFITS, PUNITIVE DAMAGES, OR FOR ANY
OTHER INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF THEY
WERE FORESEEABLE OR RISCO HAS BEEN INFORMED OF THEIR POTENTIAL.
Contacting RISCO Group
RISCO Group is committed to customer service and product support. You can contact us through our website (www.riscogroup.com) or at the following telephone and fax numbers:
United Kingdom
Tel: +44-(0)-161-655-5500
support-uk@riscogroup.com
Italy
Tel: +39-02-66590054
support-it@riscogroup.com
Spain
Tel: +34-91-490-2133
support-es@riscogroup.com
France
Tel: +33-164-73-28-50
support-fr@riscogroup.com
Belgium (Benelux)
Tel: +32-2522-7622
support-be@riscogroup.com
USA
Tel: +1-631-719-4400
support-usa@riscogroup.com
China (Shanghai)
Tel: +86-21-52-39-0066
support-cn@riscogroup.com
Israel
Tel: +972-3-963-7777
support@riscogroup.com
FCC ID: JE4RP432KPP2
IC: 6564A-RP432KPP2
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
FCC Note
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment on and
off, the user is encouraged to try to correct the interference by one or more
of the following measures: Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver. Connect the
equipment into an outlet on to a different circuit from that to which the
receiver is connected. Consult the dealer or an experienced radio/TV
technician for help.
IC Warning
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>