PROCET PT-PR01G PoE Surge Protector User Guide
- June 17, 2024
- PROCET
Table of Contents
PROCET PT-PR01G PoE Surge Protector
Specifications
- Input Voltage: 60Vdc (Max)
- Max Discharge Current: 10KA(8/20us,1.25KA per line)
- Maximum Operating Current: 1A for 2 pairs, 2A for 4 pairs
- Maximum Operating Power: 120W Max
- Protected Line: 1,2,3,4,5,6,7,8
- PoE Surge Protection:
- Common Mode Protection Level(10/700us): 10KV
- Differential Mode Protection Level(10/700us): 1.5KV
- Data Speed: 10/100/1000Mbps
- Operating Temp.: -40 to 85
- Operating Humidity: 20%-80% non-condensation
- Operating Altitude: Up to 5000 meters
- Storage Temp.: -40 to 85
- Storage Humidity: 10%-90% non-condensation
- Regulatory Compliance: CE
- IP Rated: IP40
- Dimensions & NW: 103mm X 28mm X 30mm, 71.5g
FAQ
- Q: What is the maximum operating voltage of the PT-PR01G?
- A: The maximum operating voltage is 60Vdc.
- Q: What type of cables should I use for 100Base-TX Ethernet?
- A: We recommend using Cat 5 or higher UTP/STP cables.
- Q: What are the dimensions and weight of the PT-PR01G?
- A: The PT-PR01G has dimensions of 103mm X 28mm X 30mm and weighs 71.5g.
Declaration
This document belongs to PROCET company. It is not allowed to reproduce and
modify without the original author’s permission. It is PROCET’s policy to
improve its products as new technology, components, software, and firmware at
any time.PROCET, therefore, reserves the right to change specifications
without prior notice. Please follow WEEE (Waste Electrical and Electronic
Equipment) disposal instructions for old electronic products. Please do not
dispose of the old product in your general household waste bin.
The symbol indicates that the product should notbe discarded as unsorted waste
but must be sent to separate collection facilities for recovery and recycling.
Overview
The installation Guide for PT-PR01G and mainly introduces the hardware
specification, installation methods, and precautions of the installation.
There may be differences in the appearance and configuration from other
models. All product images in this manual are for illustration purposes only
and may differ from the actual product.
This manual includes the following chapters:
- Product Introduction. Including the basic functions and specification of PT-PR01G, as well as the product appearance and applications introduction.
- Installation Introduction. Introducing the preparation work and precautions before installing the product.
- Product Installation.
For whom
- Network Engineers
- Network Administrators
- Field Technicians
Introduction
PT-PR01G is a single-port Ethernet surge protector. Enclosed in an Aluminum Alloy shell, with a silver color exterior, complemented by an anodized aluminum surface. Enhanced RJ45 socket exhibits minimal signal attenuation. High-quality Gas discharge tube(GDT). Withstand extreme environmental conditions within a temperature range of -40 to 85 degrees Celsius. Max Discharge Current: 10KA (8/20us, 1.25KA per line). Supports power of 120W, 60Vdc(max) Ethernet equipment. PT-PR01G can not only work with IEEE802.3af/at/bt/PoE++ standard devices, but also supports non-standard Ethernet equipment, that well protects your devices against surge damage. The common mode surge voltage exceeds 10KV(10/700us) and the differential mode surge voltage is 1.5KV(10/700us).
Appearance
Upper View
Side View
Front View
Specification
| Items | Description |
|---|---|
| Input Voltage | 60Vdc (Max) |
| Max Discharge Current | 10KA(8/20us,1.25KA per line) |
| Maximum Operating Current | 1A for 2 pairs, 2A for 4 pairs |
| Maximum Operating Power | 120W Max |
PoE Surge Protection
| Protected Line: 1,2,3,4,5,6,7,8
Common Mode Protection Level(10/700us): 10KV
Differential Mode Protection Level(10/700us): 1.5KV
Data Speed| 10/100/1000Mbps
Operating Temp.| -40℃ to 85℃
Operating Humidity| 20%-80%，non-condensation
Operating Altitude| Up to 5000 meters
Storge Temp.| -40℃ to 85℃
Storge Humidity| 10%-90%，non-condensation
Regulatory Compliance| CE
IP Rated| IP40
Dimensions & NW| 103mm X 28mm X 30mm（71.5g）
Installation
Packing Contents
Open the box of the PT-PR01G and carefully unpack it, the box should contain
the following items:
Installation Toolkits
These tools may be needed during equipment installation, and should be prepared by yourself: level ruler, marking pen, craft knife, wire stripper, network pliers, impact drill,different matching drilbits, rubber hammer, cross screwdriver, wrench, ladder, etc.
Inspection
Connect the PT-PR01G with the protected device, and check if the terminal
device work normally.
Caution：
- We recommend to use Cat5 or higher UTP/STP cables for 100Base-TX Ethernet；
- We recommend to use Cat5e or above UTP/STP cables for 1000Base-T Ethernet
Caution
- This device is for indoor use only. If you need to use it outdoors, please use it with a waterproof case.
- Please use Cat 5e or ethernet cables with shielding.
- Grounding is required when using.
- It is recommended to place the device in close proximity to the protected equipment with a distance of ≤50cm. Vertical installation is also recommended with a tilt angle not exceeding 50°.
- Please install the device on a wall or metal back panel. Do not use a wooden back panel to prevent the risk of fire.
Installation
This product is safe to use wall-mounted installation
Wall mounting
If it is placed in an outdoor environment, please install the device in a
waterproof case with a height of 45cm if possible. 3.1.1Fix the product with
screws and tighten them into the screw holes.
Inspection
Inspect the installed equipment before putting it into operation：
- Make sure the PD connected can work normal.
- Make sure the Ethernet cable connection is correct.
- Make sure the Grounding is correct.
Caution：
Waterproof Ethernet cables should be with a protective sheath. CAT5e/6 cables are recommended
Grounding
PROCET Single port PoE surge protector PT-PR01G has the following grounding solutions for reference during construction: If the installation is in the computer room, it can be connected to the dedicated grounding busbar in the room.The grounding busbar is a connecting conductor between the grounding bodies of the building, such as flat iron, flat steel, nanomaterial conductors, copper-clad steel
For the safety of personnel and equipment in an environment without dedicated ed grounding equipment, a simple grounding device can be constructed as follows:
- a. Prepare a 6mm 2 grounding wire or a braided soft copper wire.
- b. Prepare a copper tube or angleiron,or other metal tube, bury it underground to a depth of one meter or more as a grounding electrode.
- c. Use the grounding wire to connect the external grounding terminal of the product to the metal tube. (or angle iron)
Cautions:
Use a galvanized metal pipe buried underground at a d epth of one meter or more, such as a water or sew-age pipe, as an emergency grounding if no other grounding environment is available.
Creative Lianjie Network Technology Co.Ltd
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>