StarTech USB210AIND-USB-A-HUB 10 Port Industrial USB 2.0 Hub User Guide

StarTech USB210AIND-USB-A-HUB 10 Port Industrial USB 2.0 Hub

Product Information

The 10-Port Industrial USB 2.0 (480 Mbps) Hub with 15 kV/8 kV Air/Contact ESD Protection is a high-performance hub designed for industrial applications. The hub is wall or DIN rail mountable and comes with a USB Type-B host port, ten USB Type-A ports, and a DC power input. The hub is compatible with external DC power adapters
or terminal block power sources with a voltage range of +5 – 24 V DC. The hub is designed to protect connected devices from electrostatic discharge (ESD) and features mounting holes for easy installation.

Product Usage Instructions

1. Connect the USB Type-A to Type-B cable from the USB Type-B host port on the hub to a USB-A port on the host computer.

2. The host computer’s operating system will detect the USB hub.

3. Connect up to ten USB peripheral devices to the USB Type-A ports on the USB hub.

4. To power the hub using the 2-wire terminal block, remove the terminal block connector housing from the USB hub’s casing, loosen the screws for the terminals located on the terminal block connector, connect the positive and negative wires from the DC power source to the terminals, and insert the terminal block connector housing back into the USB hub.

5. To mount the hub onto a wall, use a stud finder to locate wall studs, mark the location of the mounting holes on the wall, drill pilot holes into each mounting hole mark, align the mounting holes on the hub with the pilot holes, insert the mounting screws through the wall mounting holes and into the wall, and tighten the mounting
   screws until the hub is securely fastened to the wall.

6. To mount the hub onto a DIN rail horizontally, align the DIN rail brackets with the DIN rail mounting holes located on either side of the USB hub, insert the mounting screws through the DIN rail brackets and into the USB hub, and tighten the mounting screws.

7. To mount the hub onto a DIN rail vertically, align the DIN rail bracket with the DIN rail mounting holes located on the USB hub, insert the mounting screws through the DIN rail bracket and into the USB hub, and tighten the mounting screws.

10-Port Industrial USB 2.0 (480 Mbps) Hub – 15 kV/8 kV Air/Contact ESD Protection – Wall/DIN Rail Mountable

Product Diagram

(USB210AIND-USB-A-HUB)

Package Contents

• USB 2.0 Hub x 1
• DIN Rail Mounting Brackets x 2
• USB 2.0 Type-A to Type-B Cable x 1
• Screw Kit x 1
• Quick-Start Guide x 1

Requirements

For the latest product information, technical specifications, manuals, and declarations of conformance, please visit: www.startech.com/USB210AIND- USB-A-HUB

• Flat Head Screwdriver
• Phillips Head Screwdriver
• Writing Utensil
• Level
• DC Power Source
• (Optional) Stud Finder & Electric Driver

Installation

Notes

• Connect the Power Source after all the other installation steps have been completed.
• There are two ways to power the USB Hub.
  Using an external DC Power Adapter or a Terminal Block Power Source. Voltage (+5 – 24 V DC).

Connect the USB Ports

1. Connect the USB 2.0 Type-A to Type-B Cable to the USB Type-B Host Port, located on the USB Hub, and to a USB-A Port, located on the Host Computer.
2. The Host Computer’s Operating System will detect the USB Hub.
3. Connect up to 10 USB Peripheral Devices to the USB Type A Ports, located on the USB Hub.

Power the Hub

Power the Hub Using the 2-Wire Terminal Block

1. Remove the Terminal Block Connector Housing from the USB Hub’s Casing.

2. Loosen the screws for the Terminals located on the Terminal Block Connector, using a Flat Head Screwdriver.

3. Connect the Positive and Negative Wires from the DC Power Source (+5 – 24 V DC) to the Terminals on the Terminal Block Connector, the Terminals are marked on the USB Hub’s Casing.
   Note: Ensure the polarity of the power input is correctly matched with the DC 2-Wire Terminal Block Pins to function properly and to prevent damage to the USB Hub and any connected peripherals.

4. Insert the Terminal Block Connector Housing back into USB Hub.
   Power the Hub Using an External Power Adapter
   Connect the Power Adapter to the Power Input Port, located on the front of the USB Hub and to an AC Electrical Outlet.

Surface Mounting

Note: Always mount onto Wall Studs, when installing the USB Hub onto drywall.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.

Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.

CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

1. (Optional) If mounting onto drywall, use a Stud Finder to locate the Wall Stud(s) on your wall.
2. Hold the Hub in the desired mounting location, and mark the location of the Mounting Holes, using a Writing Utensil (use a level to ensure the two Mounting Holes are level).
3. Using an Electric Driver, drill Pilot Holes into each of Mounting Hole Marks.
4. Hold the Hub in the desired mounting location, aligning the Mounting Holes on the Hub with the Pilot Holes created in Step 3.
5. Insert the Mounting Screws (x 2) through the Wall Mounting Holes and into the Wall, and tighten the Mounting Screws until the Hub is securely fastened to the Wall, using a Phillips Head Screwdriver.

DIN Rail Mounting

Horizontal

1. Align the Din Rail Brackets (x 2) with the DIN Rail Mounting Holes, Horizontal (x 4), located on either side of the USB Hub (rear).
2. Insert the Mounting Screws (x 4) through the DIN Rail Brackets and into the USB Hub.
3. Using a Phillips Head Screwdriver, tighten the Mounting Screws. Be careful not to over-tighten the Mounting Screws.

Vertical

1. Align the Din Rail Bracket (x 1) with the DIN Rail Mounting Holes, Vertical (x 2) located on the USB Hub (rear).
2. Insert the Mounting Screws (x 2) through the DIN Rail Bracket and into the USB Hub.
3. Using a Phillips Head Screwdriver, tighten the Mounting Screws. Be careful not to over-tighten.

Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Safety Measures
If product has an exposed circuit board, do not touch the product under power.

StarTech.com Ltd.
Unit B, Pinnacle 15 Gowerton Rd,Brackmills Northampton NN4 7BW United Kingdom

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

References

• Industrial 4 Port USB C Hub 10Gbps 3A/1C - Industrial USB Hubs | StarTech.com
• 10-Port Industrial USB 2.0 HUB, Metal - Industrial USB Hubs | StarTech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>