PHOENIX BXBGS01 Sports Sunglasses with Audio User Manual

PHOENIX BXBGS01 Sports Sunglasses with Audio

Technical information

• Bluetooth version: Bluetooth V5.1
• Bluetooth profiles: HFP, HSP, A2DP, AVRCP
• Operating distance: 10m
• Battery capacity: 100mAh
• Autonomy: Up to 5 hours (Maximum volume) | Up to 6.5 hours (50% volume)
• Charging time: 1.5 hrs.
• Charging input: DC 5.0V 500mA
• Protection: IPX5
• Category: 3
• UV protection:
• Grey Lens: UV400
• Clear Lens: UV320
• Dimensions: 162.9 × 162.8 × 53.4mm
• Weight: 43.3g (Glasses)

Box contents

• 1× Sport Audio Sunglasses
• 2 × Lenses
• 3 x Nose pads S-M-L sizes
• 1x Cleaning cloth
• 1x Charging cable
• 1× Case with hook
• 1 × User manual

Diagram

1. Side piece
2. Ambient noise cancelling microphone
3. Force sensor
4. Lens
5. Speaker
6. Nose pads
7. Call microphone
8. Charging magnetic shock
9. Indicator light (red, blue)

Introduction

PHOENIX are sunglasses with integrated audio and Bluetooth. You can listen to various audio content wirelessly or make calls while doing sports such as cycling or skiing.

How to charge the glasses
If during use, the red light flashes 4 times per minute, this indicates that the battery is low and you need to charge the glasses.

1. Connect the glasses to the charging cable. Make sure the magnetic contact between the goggles and the charging cable is in place and start charging when the red indicator light on the goggles is on.
   • Charging: the red light is on.
   • Fully charged: the red light is off.
2. Fully charged time: approximately 2 hours.

Caution: If you have not used the glasses for a long time, it is recommended to charge them at least once every 3 months to prevent the battery from draining and entering sleep mode.
Warning: The rechargeable battery of this product should be disposed of properly for recycling. Contact your local recycling centre for proper disposal methods. Do not place the battery in a fire to avoid causing an explosion.

Placement of nasal pillows

Before wearing the goggles, fit your size nose pads. According to the height of your nose bridge, choose the most suitable nose pad to insert into the glasses frame.

On/ Off

1. Make sure the glasses are charged before use. You will know they are 100% charged when the red LED indicator is off.
2. Switch on the glasses. To do this, you will need to open the right temple. At this point the blue light will turn on and the glasses will indicate “connected”.
3. Switch off the glasses. When the temples are folded and closed, the glasses will automatically turn off and the red light will remain on for approximately 1 second.

Note: When the glasses are inactive and not connected to the device, they will automatically enter pairing mode after 10 seconds. Pairing mode will be maintained for 5 minutes. If they’re not paired with any mobile phone for more than 5 minutes, the glasses will automatically turn off.

Connection
Pair your mobile phone with the glasses after turning them on and placing them on your face:

1. Connection: press and hold the sensor for 5 seconds to enter pairing mode in power-on state, release it when you see the red and blue lights flash alternately, and the glasses request pairing.
2. Pairing: When the glasses are in pairing mode, search for the name “PHOENIX” in the phone’s Bluetooth list and click Connect. Once the pairing is successful, the glasses will indicate ‘Connected’.
3. Operating: To control the mobile phone from your glasses, you will need to control it from the sensor part located at the bottom of one of the temples.

• The mobile phone will recognize the glasses automatically 10 seconds after starting up, and will enter pairing mode after a failure.

Glasses control

Music

Pause

|

Playing music

|

Signal click button

|

1time Du

Play

|

Stop playing

|

Signal click button

|

1time Du

Previoussong| Playing music| Triple click button| 3times Du
Next song| Playing music| Double click button| 2times Du

Calls

Cancel calling

|

Calling

|

Signal click button

|

Hime Du

Answering

|

Incoming call ringing

|

Signal click button

| Rising pitch after 1 time Du

Reject

|

Incoming call ringing

| Press and hold the button for 2

seconds, and you will hear a prompt tone

| Falling pitch after 1 time Du

End calling

|

During a call

|

Signal click button

|

Falling pitch after 1 time Du

Connected mobile phone operation

Voice dialing

| ****

Connected with phone

| ****

Long press the button for 2 seconds and let go when you hear the prompt

| ****

Rising pitch after 1 time Du

---|---|---|---

Exit voice dialing

| ****

Connected with phone

| ****

Long press the button for 2 seconds and let go when you hear the prompt

| ****

Rising pitch after 1 time Du

Changing lenses

1. Remove the nose pad you have chosen for your nose and leave it in a place where it can be seen.
2. Carefully, pull the lens away from the part of the glasses where the nosecup is located.
3. Grasp the spectacle firmly from the top centre with one hand, and with the other hand, grasp the lens of the spectacle and press downwards. The lens will come out without any problem.
4. To fit a new lens, you will need to place the new lens on the marked lines inside the glasses (both on the frame of the glasses and on the nose), press down to secure it and push the nose pad back into place.

Battery Status

When the glasses are connected to an iOS device or Android device, the battery of the glasses will be displayed on the device. When the glasses are low on battery, the battery indicator will turn red and display a low battery icon. For different phone models, there may be different ways to display the battery life. The following is a screenshot of the battery life on the iOS phone.

Meaning of Indicator light

Glasses

Status of glasses

|

Indicator

---|---

Pairing

|

Red and blue LED flash quickly alternately

Unconnected

|

Blue LED flashes every 5 seconds

Connected

|

Blue LED flashes twice every 10 seconds

Low battery

|

Red LED flashes four times every minute

Factory Reset

In pairing mode, press the touch sensor four times and watch the red and blue lights turn on for 2 seconds. The factory reset will then be completed.

Note: After resetting to factory settings, clear the pairing records of the glasses and phone, open the temples to turn on the glasses and automatically enter pairing mode (red and blue lights will flash alternately). You will need to pair and connect the glasses with the phone again.

Care and maintenance

Please read the following recommendations carefully before using Ksix PHOENIX glasses.

• Keep the product in dry places and do not put it in a humid place to avoid affecting the internal circuitry of the product. Do not wear the glasses during heavy exercise to prevent sweat from entering.
• Keep the product away from direct sunlight or hot places. High temperatures shorten the life of electronic devices, destroy the battery or deform certain plastic parts.
• Do not use the product in very cold areas. This may damage the internal circuit board.
• Do not attempt to disassemble the product as this may damage it.
• Do not drop it on the floor or other hard surfaces. This may damage the internal circuitry.
• Do not use harsh chemicals or detergents to clean the product.
• Do not scratch the surface with sharp objects.
• In case of product malfunction, up to 3 years warranty is available.

Notes

1. If the red LED flashes slowly four times per minute, it means that the battery is low on power and needs to be recharged.
2. If the red LED is off during charging, it means that the magnetic attraction of the charging cable may not be in contact with the magnetic attraction of the temple.
   • Please make sure that the metal contacts of the glasses and the charging cable are free of obstructions.
   • If the glasses are not used for a long time, the battery will go into an idle state. At this point, it needs to charge for about 30 minutes before the red light comes on.
3. If you do not hear sound from your glasses, you should consider the following points:
   • Confirm that the phone volume is appropriate;
   • Confirm that the glasses are properly connected to the mobile phone;
   • Check if the glasses are too far away from the mobile phone or if there are any interfering objects around them.
4. To ensure the sound clarity of your glasses:
   • Make sure the mobile phone is in the strong signal area;
   • Make sure that the glasses are in the available range.
5. If pause/play, last/next song does not work when playing music, make sure your Bluetooth device supports AVRCP (audio/video remote control profile).

Maintenance recommendations

• Regularly clean the product with a dry cloth. The product must be disconnected or switched off when you clean it.
• Keep the connectors and/ or ports free from dust, lint, etc. to prevent improper connections.
• Avoid breaking the device. Do not put objects over it or bend it too strong.
• If the product includes a cable do not bend it too strong and do not pull from it to unplug the product.
• Do not wet the product. Keep it always in a dry place, away from humidity.
• When not using the product, store it in a place free from dust, dirt, lint, liquids, etc.
• If water or other liquids enter the product interior, unplug it immediately from any attached power source or device it is connected to.
• Avoid dropping or hitting the product. It might be damaged.
• Do not use the product for anything other than its intended use.
• Please recycle the product in accordance with local environmental laws and regulations.

Safety information

Please read the following instructions before using the device for the first time:

• When you use device keep it away from heat sources (fire) and from humidity sources (water and other liquids).
• If the product is wet or damaged do not us it.
• Do not use the product with wet hands.
• Do not leave the product in contact with flammable materials.
• Do not expose the product to high temperatures (for example: inside a car during hot weather)
• Do not throw the product into fire.
• Keep the product away from children.
• Disconnect or switch off the product if you are not going to use for a long period of time.
• Do not use the device if you perceive any visible defects.
• Do not attempt to open or puncture the product. You might damage it.
• Do not use the product with incompatible devices.
• Do not dismount or modify the product. These actions will invalidate the Warranty.

Legal Note
Hereby, Atlantis Internacional S.L. declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EC. The features and functions described in this manual are based on tests made by Atlantis Internacional S.L. It is the user’s responsibility to examine and verify the product after its purchase. Atlantis Internacional S.L. is not responsible and will never be liable for any personal loss or injury, economical loss, material loss or any damage due to misuse, abuse or improper installation of the product. For electronical devices with Bluetooth: Atlantis Internacional S.L. is not responsible and will never be liable for any function, communication and connection failure between the product and Bluetooth enabled devices.

Electronic and electrical devices disposal
This symbol indicates that electrical and electronic equipment is to be collected separately.

This product is designated for separate collection at an appropriate collection point.

• Do not dispose of as household waste.
• The final price of this product includes the cost necessary for the correct environmental management of the generated waste.
• If the equipment uses batteries, they must be removed from the equipment and disposed in an appropriate collection center. If the batteries cannot be removed, do not attempt to do it yourself since it must be done by a qualified professional.
• Separate collection and recycling helps conserve natural resources and prevent negative consequences for human health and the environment that might result from incorrect disposal.
• For more information, contact the retailer or the local authorities in charge of waste management.

CE Declaration of Conformity

We hereby declare that the product (s) listed below satisfies the provision for CE-marking according to the following European directive(s):

• EN 62368·1:2014+A11:2017
• EN 50663: 2017; EN 62479: 2010
• ETSI EN 301 489-1 V2.2.3 (2019-11)
• ETSI EN 301 489-17 V3.2.4 (2020-09)
• EN 55032: 2015; EN 55035: 2017
• ETSI EN 300 328 V2.2.2 (2019-07)
• Article: BXBGS01
• EAN: 8427542126081
• Model: BTH188Q

Manufacturer

• ATLANTIS INTERNACIONAL, S.L.
• Address:
• Carrer del Crom, 53, 08907 L’Hospitalet de Llobregat, Barcelona (Spain)
• Place and date of the declaratlon:
• L’Hospitalet de Llobregat, 1 of September 2022

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>