L6OP7xx Proled Flex Strip Opal Shape Instruction Manual

L6OP7xx Proled Flex Strip Opal Shape

PROLED FLEX STRIP OPAL SHAPE L6OP7xx

Characteristics:

• SMD CHIP MONO (neutral white, warm white, super warm white).
• Power supply 24 VDC.
• Homogenous light. No single points visible.
• Safety class IP65. Suitable for wet room and covered outside.
• Operating temperature range -10° C till +45° C.
• CE compliant with applicable European directives.
• This product contains a light source of energy efficiency class F.

Warning:

1. For covered outside use possible.
2. Please ensure that the packaging is disposed of in a safe environment.
3. We do recommend that a qualified electrician should be used to install the products.
4. Do not look at the lighted lamp directly.
5. Please watch out at installation for thermal expansion or shrinking.

Safety indices:
Be sure to have a qualified electrician complete installation. The customer is not entitled to claim for any lights installed without observing European safety directives. The manufacturer is then discharged from liability when damage is caused by improper use or installation. For indoor use only. Protection class IP65.

Preinstallation:
Please follow the sequence of installation step by step. Non-observance can lead to damage of the flex strip.

1. Switch off the electricity at the mains before commencing installation or lamp change and (if a fuse box is installed) remove the appropriate circuit fuse to avoid accidental switching on of the mains supply.
2. Connect the flex strip to the power supply 24 VDC output (secondary side).
3. Connect connector (primary side) of power supply to mains (220-240VAC).
4. If a dimmer is used, than it must be placed between power supply and the flex strip.

Installation possibilities:

1. Please keep in mind, that following strain is not allowed:
2. Minimum bending diameter at FLEX STRIP OPAL 360 XL

Installation

1. Please take care about following points before installation

2. Please take care about following points before deinstallation

3. Connection diagramm
   Installation and commissioning may only be performed by qualified persons.
   National installation regulations must be observed.
   Luminaires must be disconnected from mains before any work.

4. Replacement of the included light source
   Principle, the built-in light source can be replaced by a trained electrician without permanent damage to the containing product. Generally available tools are sufficient.

Installation for vertical hanging:

1. Following items are needed for a vertical installation:
   L6OP7A03 (1m) or L6OP7A03S (1m) or L6OPA04 (2,5m) or L6OPA04S (2,5m)

2. Installation steps

PC-pipe must be 22mm shorter than the Flex Strip OPAL

Pull the O-ring in the end cap of the PC-pipe

Installation for bended arrangement:

1. Following item is needed for a bended installation:
   L6OP7A08

2. Installation steps

ATTENTION: To prevent a possible hanging, depending on the shape, we suggest to use supports every 500

Put the fixings on the Flex Strip OPAL.

Installation for hanging one side or both side arrangement

1. Following items are needed for a one side or both side installation:
   L6OP7A05 (one side) or L6OP7A06 (one side) or L6OP7A07 (both sides)

2. Installation steps

Fixing at one side installation

Concrete or suspended ceiling

Fixing at two side installation Fixed position

Installation for bended, under ceiling installation:

1. Following item is needed for a bended, under ceiling installation:
   L6OP7A12

2. Installation steps

Installation for straight, under ceiling installation, length 1m:

1. Following item is needed for a straight, under ceiling installation:
   L6OP7A09

2. Installation steps

Installation for bended straight, suspended installation, length 1m:

1. Following items are needed for a straight, suspended installation:
   L6OP7A10 or L6OP7A11 and L6OP7A14

2. Installation steps

Installation of connectors:

1. Following item is needed for a connector:
   L6OP7A08

2. Installation steps Put the connection ring on the Flex Strip OPAL Move the connection ring back to the connector

MBN GmbH, Balthasar-Schaller-Str. 3, 86316 Friedberg – Germany www.proled.com

References

• PROLED: proled.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>