WYNDHAM COLLECTION WC-4141-84-DBL 84 Inch Double Vanity Installation Guide

WYNDHAM COLLECTION WC-4141-84-DBL 84 Inch Double Vanity

Product Information

The product is a bathroom cabinet that comes with a main cabinet, a counter and sink (optional), a mirror (optional), and screws for the mirror (optional). The product has a backsplash that comes in two pieces. The cabinet should be installed on a level surface and all surfaces should be protected from sharp objects, high heat sources, direct prolonged sunlight, and chemical hazards. Professional installation is recommended. The product comes with an electrical outlet with a charging hub that has two electrical outlets, two USB ports, and a power reset switch. The outlet should only be used with ground- fault circuit interrupter (GFCI) outlets and all applicable electrical codes should be followed.

Product Usage Instructions

1. Prior to installation, check all received items against the Packing List. Report any missing items to your retailer immediately.
2. Install the counter (and sink if included). Seal around the top of the cabinet with clear silicone sealant. Do not over apply. Allow to dry for 24 hours for proper curing.
3. Install the mirror (if included). Use a pencil to mark the placement of the screw holes on the wall, drill the holes, and insert the plastic wall anchors. Install the screws into the wall anchors, leaving enough of the screw exposed to hang the mirror (approximately 1/4-1/2 inch).
4. If minor door and drawer alignment is required, follow the easy directions below for adjusting hinges and drawer slides (if required).
5. Remove the handles from inside the cabinet doors and drawers and reinstall them on the outside. Do not over tighten when reattaching. Short screws are for door handles and long screws are for drawer handles.

How to Adjust Hinges (if required)

Follow the instructions below for adjusting hinges:

1. Mark the screw position on the horizontal line.
2. Use a drill with a diameter of 6mm and depth of 40mm to create the holes.
3. Install the screws into the holes, adjusting the hinge as necessary for up and down and side to side alignment.

How to Adjust Drawer Slides (if required)

Scan the QR code with your phone or visit www.wyndhamcollection.com/3dslides for detailed video instructions on adjusting drawer slides. Follow the instructions below:

1. For up and down adjustment, turn the adjustment screw clockwise to raise the drawer or counterclockwise to lower it.
2. For side adjustment, turn the adjustment screw clockwise to move the drawer to the right or counterclockwise to move it to the left.
3. For depth adjustment, turn the adjustment screw clockwise to move the drawer forward or counterclockwise to move it backward.

• Prior to installation please check received items against the “Packing List”. Please report any missing items to your retailer immediately.
• Protect all surfaces from sharp objects, high heat sources, direct prolonged sunlight and chemical hazards.
• Professional installation is recommended.
• Please install on a level surface. If minor door and drawer alignment is required, please follow the easy directions below.
• Backsplash comes in two pieces.

PACKING LIST

(Not all components may be included, depending upon your purchase)

HOW TO ADJUST HINGES

REQUIRED TOOLS NOT IN BOX

INSTALLATION INSTRUCTIONS

1. Install the counter. Seal around the top of the cabinet with clear silicone sealant. Do not over apply. Allow to dry 24 hours for proper curing.
2. Install the mirror: use a pencil to mark the placement of the screw holes on the wall, drill the holes and insert the plastic wall anchors.
3. Install the screws into the wall anchors, leaving enough of the screw exposed to hang the mirror – approx 1/4″ 1/2″.
4. Remove the handles from inside the cabinet doors and drawers and reinstall on the outside. Do not over tighten when reattaching.
5. Short screws are for the door handles and long screws are for the drawer handles.

Up and Down Adjustment

HOW TO ADJUST DRAWER SLIDES

Scan the QR code with your phone to watch detailed video instructions or visit www.wyndhamcollection.com/3dslides.

Backboard Cutouts

Electrical Outlets with Charging Hub

• Easy to install
• Long 5 foot plug in cord
• 2 electrical outlets, 125V 15A
• Tamper Resistant (TR) outlets
• Power reset switch
• 2 USB ports, 5V 2.1A Max
• Use with ground-fault circuit interrupter (GFCI) outlets only
• Residential use only
• Follow all applicable electrical codes
• ETL Listed
• Conforms to UL Standard 962A
• Certified to CAN/CSA Standard C22.2 No. 308

References

• wyndhamcollection.com/3dslides

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>