VIVOTEK AP-GXC-0100 Gigabit PoE Extender Installation Guide
- June 11, 2024
- Vivotek
Table of Contents
AP-GXC-0100 & AP-GXC-0200 Gigabit PoE Extender
Quick Installation Guide
INTRODUCTION
AP-GXC-0100: 1 PoE IN – to – 1 PoE OUT.
AP-GXC-0200: 1 PoE IN – to – 2 PoE OUT.
The AP-GXC-0100 & AP-GXC-0200is a Gigabit PoE Extender capable of receiving
30W/60W/90W power from PSE. Multiple extenders can be cascaded to increase the
cabling distance.
PACKAGE CONTENTS
- 1x PoE Extender
- 1x Quick Installation Guide
IMPORTANT:
- Install the device in a ventilated and dry place, that is free of electromagnetic source, vibration, moisture, and dust.
- Make sure the ventilation openings on the extender are not blocked.
- Use CAT.5e or 6 UTP/STP cables. Avoid using low-quality cables, which will seriously limit the cabling distance.
CONNECTION
Following are the conditions for making the cabling:
- Use 18~19, 24AWG CAT.5e cables.
- Typical cameras stream size feature = 1080p@30fps – 6Mbps; 720p@30fps – 3Mbps.
Make sure the combined bandwidth consumption does not exceed the uplink bandwidth from the PoE switch.
NOTE: There are power losses due to cable resistance.
- 90W bt PoE Injector
- AP-GXC-0100
- AP-GXC-0200
- PoE Camera
INSTALLATION
AP-GXC-0100
-
PoE Input Connect to PoE Switch
-
PoE OFF/ON Switch
-
Ground screw
* Make sure the grouning resistance is lower than 0.5Ω. -
56VDC PoE Output
AP-GXC-0200
-
PoE Input Connect to PoE Switch
-
PoE OFF/ON Switch
-
Ground screw
* Make sure the grouning resistance is lower than 0.5Ω. -
Port 1 : 56VDC PoE Output
-
Port 2 : 56VDC PoE Output
LED DEFINITIONS
| PWR | Green ON | PoE IN port is connected to PSE. |
|---|---|---|
| OFF | No PoE IN connection. | |
| PoE | Green ON | Power over ethernet cable status |
| OFF | Ethernet cable no Power | |
| LAN | Green ON | Data link is detected. |
| Green Flashing | Data is being transmitted or received. | |
| OFF | Link is not detected. |
PoE DIP SWITCH DEFINITIONS
AP-GXC-0100
| DIP# | ON | Turn on PoE output for the PoE out port. |
|---|---|---|
| OFF | Turn off PoE output for the PoE out port. |
AP-GXC-0200
| Pin 1 | ON | Port 1 Turn on PoE output |
|---|---|---|
| OFF | Port 1 Turn off PoE output | |
| Pin 2 | ON | Port 2 Turn on PoE output |
| OFF | Port 2 Turn off PoE output |
If the device that is going to be connected to this extender is not PoE PD, please turn off the PoE output function.
All specifications are subject to change without noice.
Copyright © 2022 VIVOTEK INC. All rights reserved.
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T: +886 -2-82455282|F:
+886-2-82455532|E:sales@vivotek.com
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T:408-773-8686|F:
408-773-8298|E:salesusa@vivotek.com
VIVOTEK Europe
Zandsteen 15, 2132 MZ Hoofddorp Delta Electronics
T:+31 (0)20 800 3817 E:saleseurope@vivotek.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>