BATAVIA BT-CTB001 Maxxpack 18V Twinbrush Instruction Manual

MAXXPACK 18V
Twinbrush Operating instructions
Model: BT-CTB001
Item-No.: 7064170
www.bataviapower.com

SPP Series Pen Probes

Overview

1 Retaining clip
2 Grip sleeve
3 Locking screw
4 Extra handle
5 Power supply unit
6 Locking clip
7 Battery cover
8 ON/OFF switch
9 Stopcock
10 Velcro tape
11 Hose adapter| 12 Attachment clip
13 Hose
14 Inner part of the brush
15 Outer part of the brush
16 Spindle lock button
17 Motor unit
18 Locking lever
19 Extension pole (optional accessory)
20 Socket
21 Tug strap
22 Plug
---|---

Dear customer
Please familiarize yourself with the proper usage of the device by reading and following each chapter of this manual, in the order presented. Keep these operating instructions
for further reference.
Please read the enclosed “General safety instructions for power tools” and all addi­tional safety instructions in this operating instructions!
This manual contains important information on operating and handling the device. Keep these operating instructions for further reference.
Please pass it on along with the unit if it is handed over to a third party.
The Maxxpack batteries and chargers are avail­ able online and in participating stores.

Explanation of the symbols

The following symbols are used in the user manual or on the product:
Warning! To reduce the risk of injury, the user must read the instruction manual.
Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.
Wear safety glasses.
**** CE stands for “Conformité Europé­enne”, which means “In accordance with EU Regulations”. With the CE marking, the manufacturer confirms that this Electric tool complies with the applicable European directives.
Do not dispose of electric power tools with domestic refuse.

Additional safety instructions

a. The device must be used as intended. Observe local conditions and watch out for other people in your vicinity when working with the device.
b. Before using the device, check for damages and do not use a damaged device. Should the device become damaged do not use it and have it repaired by a professional or contact our customer support department. Do not disassemble the device or try repairing it yourself.
c. WARNING: The appliance must not be operated by children or persons who have not been instructed accordingly.
d. Persons with limited physical, sensorial or mental abilities are not allowed to use the device, unless they are supervised and briefed for their safety by a qualified person. Keep the device out of reach of children.
e. Children must not clean or service the device unsupervised.
f. Supervise children to prevent them from playing with the appliance.
g. Hold the device firmly and safely when turning it on.
h. The appliance must not be operated in explosive atmospheres.
i. Always wear eye protection.
j. This device is suitable for indoor and outdoor use, but do not use in rain.
k. Check to make sure the brush accessory is installed correctly prior to use.
l. Do not force the brush into tight spaces during use.
m. Do not touch rotating parts when device is in use.

Contents of packing

1× Twin brush – Dual Power Scrubber (motor unit and power supply unit)
1× extra handle including attachment materials
1× medium brush (outer part and inner part)
1 x user manual

Before the first use

Remove the machine and all accessories from the package. Keep the packaging materials out of the reach of small children. There is a danger of suffocation!
Check all parts for damage in transit and do not use a damaged device.
4.1. Assembly
a. Place the motor unit (17) and the power supply unit (5) with the tube ends facing each other.
b. Slightly pull the socket (20) using the tug strap (21) and the plug (22) out of the tube ends. (see Fig. B)
c. Connect the socket and the plug with the arrows pointing towards each other and screw together tightly.
d. Connect the two tube ends (arrows pointing towards each other) and screw them together with the grip sleeve (2).
e. Plug the hose (13) into the connection on the motor unit. (see Fig. C)
f. Guide the hose through the retaining clip (1) and the mount on the motor unit.
Make sure that the hose on the motor unit is long enough so that the adjustable brush head can move without restriction. g. Connect the hose adapter (11) to the hose.
h. Slide the hose adapter onto the guide track of the attachment clip (12). (see Fig. D)

Intended use

This product is intended for cleaning surfaces indoors and outdoors in the domestic sector.
The product can be operated dry or with water. It is not intended for permanent commercial use.
The intended use also includes an operation following the operating instructions.
Any use beyond these parameters (different media, applying force) or any changes (recon­ struction, no original accessory) can lead to serious risks and is regarded as use that is contrary to the intended purpose.
Only use accessories recommended by supplier.

Use

6.1. Inserting/changing the battery
The battery cover protects the battery from moisture and debris.
a. Only use the device with water when the battery cover is properly closed.
b. Make sure the battery cover’s seal and rubber edge is clean and dry.
a. Undo the locking clip (6) and open the battery cover (7).
b. Insert or take out the battery (see Fig. E).
c. Always check the seal before closing the battery cover!
Remove dirt and foreign objects in the area of the seal and check whether the seal is present and undamaged.
d. Close the battery cover and lock it with the locking clip.
6.2. Attaching/changing the brush
a. Block the shaft with the shaft lock button (16) and screw on the outer part of the brush (15) in the clockwise direction (see Fig. F).
b. Insert the inner part of the brush (14) and lock it in place in the counter-clockwise direction.
c. To undo the inner part of the brush, unlock it in the clockwise direction and take it off.
d. Block the shaft with the shaft lock button and unscrew the outer part of the brush in the counter-clockwise direction.
6.3. Adjusting the tilt angle of the brush
When using the device on the ground / floor, the head should not be locked. The head can then move along with the surface to be cleaned.
Only lock the head when using the device above shoulder height.
a. Lift the locking lever (18) all the way (see Fig. G).
b. Adjust the tilt angle to your individual needs and fix it in place by pushing down the locking lever.
Do not push the locking lever through with great force. If the locking lever does not close properly, adjust the inclination of the brush slightly.
6.4. Adjusting the extra handle
a. Undo the locking screw (3). (see Fig. H)
b. Adjust the position of the attachment clip (12) and the tilt of the extra handle (4) to your needs and tighten the locking screw again.
6.5. Working with the device
a. For wet use, close the stopcock and connect the hose adapter to your water supply. Adjust the water quantity with the stopcock (see Fig. A).
b. Press the ON/OFF switch (8) to turn the device on.
It is not necessary to hold the ON/OFF switch during use.
Only exert minimal pressure (gentle feed motion) on the device when working. Gently and evenly push the device forwards.
c. Press the ON/OFF switch again to turn the device off.
6.6. Mounting the extension pole (optional accessory)
The extension pole is an optional accessory and not delivered with the device. Do not use more than one extension pole with the device.
a. Pull the hose adapter (11) off the guide rail of the attachment clip (12). (see Fig. I)
b. Unscrew the grip sleeve (2) and pull the two tube ends apart.
c. Unscrew the fitting and pull the plug (22) and the socket (20) apart.
d. Place the motor unit (17) and the exten­sion pole (19) with the tube ends facing each other.
e. Slightly pull the socket (20) using the tug strap (21) and the plug (22) out of the tube ends. (see Fig. B)
f. Connect the socket and the plug with the arrows pointing towards each other and screw together tightly.
g. Connect the two tube ends (arrows pointing towards each other) and screw them together with the sleeve (2).
h. Place the power supply unit (5) and the extension pole (19) with the tube ends facing each other.
i. Slightly pull the socket (20) using the tug strap (21) and the plug (22) out of the tube ends.
j. Connect the socket and the plug with the arrows pointing towards each other and screw together tightly.
k. Connect the two tube ends (arrows pointing towards each other) and screw them together with the sleeve (2).
l. Slide the hose adapter onto the guide track of the sleeve (23).

Maintenance, cleaning and storing

Keep the device and its accessories in good and clean condition to ensure easy and safe working.
Remove the battery pack from the tool before carrying out any adjustment, servicing or main­ tenance.
If the bristles of the brush are deformed by transport or incor­rect storage, immerse the brush in hot (90 degrees Celsius) water for 30 seconds. The bristles of the brush then return to the correct shape.

Technical data

Battery type: 18 V, 4000 mAh, LiIon
No load speed (ø100/180 mm): 200/400 min-1
Sound pressure level LpA: 66 dB(A)
Uncertainty KpA: 3 dB(A)
Sound power level LWA: 77 dB(A)
Uncertainty KWA: 3 dB(A)
Hand/arm vibration ah,b: 3.91 m/s2
Uncertainty K: 1.5 m/s2
8.1. Vibration level

The declared vibration total value and the declared noise emission values have been measured in accordance with a standard test method (EN 62841) and may be used for comparing one tool with another. The declared vibration total value may also be used in a preliminary assessment of exposure.
Warning!
The vibration and noise emission during actual use of the power tool can differ from the declared total value depending on the ways in which the tool is used, in particular, what kind of work piece is machined.
It is necessary to identify safety measured to protect the operator that are based on an esti­mation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addi­tion to the trigger time).
Try to minimize the impact of vibration and noise. Exemplary measures to reduce vibration exposure include wearing gloves while using the tool, limiting working time, and using acces­sories in good condition.

Accessories – optionally available

Item…………………………………….. Brush hard (red)
Item no:………………………………. 7064253
Thick strong hair for tough spots
Perfect for (ceramic) indoor and outdoor tiles, outdoor wooden furniture, wooden decks, walls, garage doors, and many more

Brush medium (blue)………………………… 7064252
Medium hairs for all round cleaning Perfect for boats, (ceramic) indoor and outdoor tiles, outdoor wooden furniture, wooden deck, walls, floors, and many more
Brush soft (black)……………………………. 7064251
Soft hairs for delicate surfaces
Perfect for boats, caravan/camper, tiles, metal surfaces, mobile homes, and many more
Extension pole……………………………..7064279
Extension of the reach by approx. 85 cm.

Disposal

Do not dispose of electric power tools with domestic refuse.
The electric power tool is shipped in packaging to reduce transport damage. This packaging is a raw material and as such can either be reused or can be fed back into the raw material cycle. The electric power tool and its accessories are made from various materials such as metals and plastics. Take defective components to a special refuse collection
point. Ask about these at your specialist shop or local council.
10.1. Batteries
Think of the environment when disposing of batteries. Contact your local authorities to find out where your nearest disposal area is. Do not dispose of batteries with domestic refuse. Do not dispose of by burning, risk of explosion.

Declaration of conformity

We, the Batavia B.V., Weth. Wassebaliestraat 6d, NL-7951 SN Staphorst, declare by our own responsibility that the product Twinbrush, Item-No 7064170, Model Nr. BT-CTB001 is according to the basic requirements, which are defined in the European Directives Electromag­netic Compatibility 2014/30/EU (EMC), 2006/42/EC (Machinery), RoHS: 2011/65/EU and their amendments. For the evaluation of conformity, the following harmonized stand­ards were consulted:
EN62841-1:2015+A15;
EN IEC 62841-2-3:2021;
ISO12100:2010;
AfPS GS 2019:01;
EN IEC 55014-1:2021;
EN IEC 55014-2:2021
Staphorst, 1 April 2022

Meino Seinen, QA Representative
Batavia B.V., Weth. Wassebaliestraat 6d, 7951
SN Staphorst, Netherlands
The product and the user manual may be subject to changes. Technical data may be changed without prior notice.
ONE BATTERY FOR 30+ TOOLS
MAXXPACK 18V
Cordless collection 2 YEAR WARRANTY
This product has got a 2 year warranty
Dear Client, if for any reason this product is not working, please ensure you contact our Client Service Centre. Ensure you have your original receipt of purchase. This  warranty covers all defects in workmanship or materials in this Batavia product for a two year period from the date of purchase. The warranty does not cover any malfunction, or defect resulting from misuse, neglect, alteration, or repair.

Europe
service@batavia.eu
Monday till Friday
08.00 — 17.00
(DE) 0800 664 7740
(EUR) 00800 664 774 00www.bataviapower.com
BATAVIA B.V.
Weth. Wassebaliestraat 6d
7951SN Staphorst
Netherlands

References

• Home - Batavia B.V.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>