ancona Stainless Steel Backsplash User Manual

ancona Stainless Steel Backsplash

Product Information

Backsplash 24 in. / 30 in. / 36 in.

The Backsplash is a product that is used to protect the wall behind the cooktop from food splatters and stains. It comes in three sizes, 24 inches, 30 inches, and 36 inches. The package includes one backsplash and installation hardware.

Included Parts

• 1 Backsplash
• Hardware Note: For safety reasons, backsplash mounting screws and anchors will not be included due to the variation of cabinetry constructions and wall material. Please consult your installation specialist regarding the optimal type of mounting screws and wall anchors to suit your home’s construction.

Measurements and Diagrams

The thickness of the backsplash is 0.03 inches (0.08 cm).
Refer to Figure #1 and Figure #2 for installation instructions.

Product Usage Instructions

Important Safety Instructions

Carefully read the important information regarding installation, safety, and maintenance before using the product. Keep these instructions for future reference.

Installation

1. Note: Use threaded drywall anchors only when mounting the backsplash on sheetrock. Then if necessary, remove the hood to allow installation of the backsplash.
2. Locate the midpoint of the hood at the wall. Draw a vertical centerline from this midpoint to the cooktop. (See Figure #1).
3. Open the packaging carefully to avoid damaging the backsplash.
4. Position the backsplash on the wall centered on the marked centerline and with lower edge flush with the cooktop/counter.
5. Mark where the screw holes are on the bottom and the top, drill the holes and screw in wall anchors. (See Figure #2)
6. Fix the backsplash to the wall with screws on the bottom and the top.
7. Remove the plastic cover from backsplash once it’s fixed to the wall.
8. If necessary, replace the hood, with grease trays, filters, and lights.

Use and Care Information

Clean the exterior surfaces of the backsplash regularly to maintain its appearance. Please register your product warranty by visiting the Ancona Home website. For any queries, contact customer service through phone, fax, email, or website.

Included Parts

Hardware Note: For safety reasons, backsplash mounting screws and anchors will not be included due to the variation of cabinetry constructions and wall material. Please consult your installation specialist regarding the optimal type of mounting screws and wall anchors to suit your home’s construction.

Measurements and Diagrams

Installation

IMPORTANT SAFETY INFORMATION

• READ ALL INSTRUCTIONS BEFORE INSTALLING
• The backsplash installs to cover the wall space from the bottom of the hood to the cooktop/counter.
• It can be installed during the installation of the hood or after.
• If the hood is already installed, remove the hood filters, grease trays and lights and put in a safe place.
• Then if necessary, remove the hood to allow installation of the backsplash.

1. Locate the midpoint of the hood at the wall. Draw a vertical centerline from this midpoint to the cooktop. (See Figure #1).
2. Open the packaging carefully to avoid damaging the backsplash.
3. Position the backsplash on wall centered on the marked centerline and with lower edge flush with the cooktop/counter.
4. Mark where the screw holes are on the bottom and the top, drill the holes and screw in wall anchors.
5. Fix the backsplash to the wall with screws on the bottom and the top. (see Figure #2)
6. Remove the plastic cover from backsplash once it’s fixed to the wall.
7. If necessary, replace the hood, with grease trays, filters and lights.

Use and Care Information

Cleaning Exterior Surfaces

• Clean periodically with hot soapy water and clean cotton cloth. DO NOT use corrosive or abrasive detergent (e.g. Comet Power Scrub®, EZ-Off® oven cleaner), or steel wool/scoring pads, which will scratch and damage the stainless steel surface. For heavier soil use liquid degrease such as “Formula 409®” or “Fantastic®” brand cleaner.

• If backsplash looks splotchy (stainless steel hood), use a stainless steel cleaner to clean the surface of the backsplash. Follow directions of the stainless steel cleaner.

• CAUTION: DO NOT leave on too long as this may cause damage to the backsplash finish.
  Use a soft towel to wipe off the cleaning solution, gently rub off any stubborn spots. Use a dry soft towel to dry the backsplash.

• After cleaning, you may use non abrasive stainless steel polish such as 3M® or ZEP®, to polish and buff out the stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.

• DO NOT allow deposits to accumulate or remain on the backsplash.

• DO NOT use ordinary steel wool or steel brushes. Small bits of steel may adhere to the surface and cause rusting.

• DO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods. Many of these compounds contain chemicals, which may be harmful.

• Rinse with water after exposure to these compounds and wipe dry with a clean cloth.

• Please register your product warranty by visiting the Ancona Home website.

• Canada & USA

• Phone: 1-800-350-4562

• Fax:800-350-8563

• Email:service@anconahome.com

• Website:www.anconahome.com

• © 2020 Copyright of Ancona Home. All rights reserved. This material may not be reproduced, displayed, modified or distributed.

References

• Ancona Home | High Quality Kitchen & Bathroom Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>