FLEX FX2351 24V Brushless 5 In Deep Cut Band Saw Instruction Manual

FLEX FX2351 24V Brushless 5 In Deep Cut Band Saw

SAFETY SYMBOLS

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
Be sure to read and understand all safety instructions in this Owner’s Manual, including all safety alert symbols such as “DANGER,” “WARNING,” and
“ CAUTION ” before using this tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury.

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

| This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
| DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.
| WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
| CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages
These inform the user of important information and/or instructions that could lead to equipment or other property damage if they are not followed. Each message is preceded by the word “NOTICE”, as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are not followed.

The operation of any power tools can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend a Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection which is marked to comply with ANSI Z87.1.

GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery operated (cordless) power tool.

Work Area Safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety

Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

Personal Safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dustrelated hazards.
Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power Tool Use and Care

Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation.
If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery Tool Use and Care

Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a fire. Under abusive conditions, liquid may be ejected from the battery; avoid contact.
If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion.
Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Never service damaged battery packs.
Service of battery packs should only be performed by the manufacturer or authorized service providers.

SPECIFIC SAFETY RULES FOR BAND SAW

• Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessories contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

ADDITIONAL SAFETY WARNINGS

• Keep hands away from cutting area and blade. Keep your other hand on the front handle. If both hands are holding the saw, they cannot be cut by the blade.

• Secure the workpiece. Clamping devices or a vise will hold the workpiece in place better than the hand.

• Always wait until the blade has come to a complete stop before placing the tool down. The blade can jam and lead to loss of control over the power tool.

• Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
  – Lead from lead-based paints.
  – Crystalline silica from bricks, cement, and other masonry products.
  – Arsenic and chromium from chemically-treated lumber.

• Your risk from these exposures varies, depending upon how often you do this type of work. To reduce your exposure to these chemicals:
  – Work in a well-ventilated area.
  – Work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.
  – Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote absorption of harmful chemicals.

SYMBOLS

IMPORTANT : Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.

surface speed, orbits, etc. per minute
O| Off position| Zero speed, zero torque…
1,2,3,…
Ⅰ,Ⅱ,Ⅲ,| Selector settings| Speed, torque, or position settings. Higher number means greater speed
CFM| Cubic Feet Per Minute| Air volume
MPH| Miles Per Hour| Air velocity
| Infinitely variable selector with off| Speed is increasing from 0 setting
| Arrow| Action in the direction of arrow
| Alternating current| Type or a characteristic of current
| Direct current| Type or a characteristic of current
| Alternating or direct current| Type or a characteristic of current
| Class II tool| Designates Double Insulated Construction tools.
| Protective earth| Grounding terminal
| Li-ion RBRC seal| Designates Li-ion battery recycling program
| Read the instructions| Alerts user to read manual
| Wear eye protection symbol| Alerts user to wear eye protection
| Wear mask symbol| Alerts user to wear dust mask
| Always operate with two hands| Alerts user to always operate with two hands
| Do not use the guard for cut-off operations| Alerts user not to use the guard for cut-off operations

SYMBOLS (CERTIFICATION INFORMATION)

| This symbol designates that this tool is listed by Underwriters Laboratories.
| This symbol designates that this component is recognized by Underwriters Laboratories.
| This symbol designates that this tool is listed by Underwriters Laboratories, to United States and Canadian Standards.
| This symbol designates that this tool is listed by the Canadian Standards Association.
| This symbol designates that this tool is listed by the Canadian Standards Association, to United States and Canadian Standards.
****| This symbol designates that this tool is listed by the Intertek Testing Services, to United States and Canadian Standards.

FUNCTIONAL DESCRIPTIONS AND SPECIFICATIONS

SPECIFICATIONS

Rectangular Stock: 5″ x 5″ (127 mm x 127 mm)
Blade Dimension| 44-7/8″ × 1/2″ × 0.02″
(1140 mm x 12.7 mm x 0.5 mm)
Recommended operating temperature| -4 – 104°F (-20 – 40°C)
Recommended storage temperature| < 122℉ (< 50℃)

ASSEMBLY

Detach the battery pack from the tool before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally.

TO ATTACH/DETACH BATTERY PACK (FIG. 2)

To attach the battery pack: Align the raised ribs on the battery pack with the grooves in the tool, and then slide the battery pack onto the tool.
NOTICE: Make sure that the latch on the battery pack snaps into place and that the battery pack is secured to the tool before beginning operation.
NOTICE: When placing the battery pack onto the tool, be sure that the raised ribs on the battery pack align with the grooves inside the tool and that the latches snap into place properly. Improper attachment of the battery pack can cause damage to internal components.

To detach the battery pack:
Depress the battery-release button located on the front of the battery pack, to release the battery pack. Pull the battery pack out and remove it from the tool.
Battery tools are always in operating condition.
Therefore, remove the battery when the tool is not in use or when carrying it at your side.

BLADES AND BLADE SELECTION
This band saw is designed to use .020″ (0.5 mm) thick, 1/2″ (12.7 mm) wide and 44 – 7/8″ (1140 mm) long blades. DO NOT use more than .020″ (0.5 mm) thick blades.
The special .020″ thickness reduces flexure fatigue and provides maximum tooth life. To maximize cutting life, use a blade with the correct pitch (teeth per inch) for the specific cutting job.

Blades are available in several pitches. To select the proper blade, three factors should be considered: The size, shape, and type of material to be cut.
The following suggestions are for selecting the right blade for various cutting operations. Keep in mind that these are broad guidelines and that blade requirements may vary depending upon the specific size, shape and type of material to be cut.

| For tough stock 3/16″ up to 3-1/4″ in diameter or width.
---|---
| For tough stock 5/32″ up to 3/4″ in diameter or width.
| For thin-wall tubing and thin sheets heavier than 21 gauge.
| For thin-wall tubing and thin sheets heavier than 21 gauge.

Generally, soft materials require coarse pitch blades and hard materials require fine pitch blades. Use coarse pitch blades for thick work and fine pitch blades for thin work.

INSTALLING/REMOVING BLADE

An unsuitable or incorrectly fitted band saw blade can damage the saw. Use only band saw blades that are suitable for this saw.
The saw blade may be very sharp. Always wear gloves when changing saw blades.

To Install Blade

1. Remove the battery pack from the tool.

2. Turn the band saw over and place it on a workbench or table with the front handle to the right.

3. Holding the tool with one hand, raise up the upper corner of either blade cover and pull out the blade cover with the other hand, then remove it from the tool (Fig. 3a).
   

4. Repeat the procedure to remove the other blade cover from the tool.

5. Turn the band saw over again and turn the tension lock lever located on the front of the saw 180° CLOCKWISE. This releases the tension on the blade (Fig. 3b).

6. Turn the band saw over, firmly press the new blade between the blade guide rollers (Fig. 3c). Note: Be sure the teeth face down and point to the workpiece guide as shown in Fig. 3c.
   

7. Holding the blade in the guide rollers, route it around both pulleys and through the workpiece guide (Fig. 3c).

8. Make sure that the blade is fully inserted into the guide rollers and positioned squarely against the pulleys.

9. Turn the tension lock lever 180°
   COUNTERCLOCKWISE (Fig. 3d). This will secure the blade on the pulleys.
   

10. Snap the blade covers into place as shown in Fig. 3e. Ensure all cover snaps are properly seated.

11. Pull on the blade covers to be sure they are properly secured.
    BE SURE THAT THE BLADE IS PROPERLY SEATED ON THE PULLEYS BEFORE STARTING THE CUT.
    NOTICE : For new replacement blade, find the compatible blade with correct size specified in the SPECIFICATIONS.

To remove blade (Fig. 4a, 4b)

The saw blade may be very hot after use. Allow the blade to cool down and wear gloves when removing a saw blade.

1. Remove the battery pack from the tool.

2. Remove the two blade covers from the band saw.

3. Turn the tension lock lever located on the front of the saw 180° CLOCKWISE. This releases the tension on the blade for easy removal (Fig. 4a).

4. Begin removing the blade at the upper portion of the blade guard and continue around the pulleys (Fig. 4b). The blade may spring free during removal. SAW BLADES ARE SHARP. USE CARE WHEN HANDLING THEM.
   

5. The rubber surface of the pulleys should be inspected for looseness or damage when changing the blade. Wipe any chips from the pulleys. This will extend the life of pulleys and keep the blade from slipping.

ADJUSTING THE 3-POSITION WORKPIECE GUIDE (FIG. 5)

1. Remove the battery pack.
2. Press the guide adjustment button and slide the workpiece guide to the desired position detent.
   

LED LIGHT

The LED light provides additional light on the surface of the workpiece for operation in lower-light areas.
The LED light will automatically turn on with a slight squeeze on the variable-speed trigger switch before the tool starts running and will turn off approximately 10 seconds after the variable-speed trigger switch is released.
The LED light will rapidly flash when the tool and/ or battery pack becomes overloaded or too hot, and the internal sensors will turn the tool off if the tool and/or battery pack are overloaded. Rest the tool for a while or place the tool and battery pack separately under air flow to cool them.
The LED light will flash more slowly to indicate that the battery is at low- battery capacity.
Recharge the battery pack.

SAW HOOK (FIG. 7)

Your tool is equipped with a hook. Use the hook to hang the saw from a rafter or beam, or other similar secure structure for temporary storage during work breaks. Recommended lumber size to support the saw with the hook: 2×4.
To use, lift up the hook until it snaps into the open position.
When not in use, always lower the hook until it snaps into the closed position.

When the saw is hung by the hook, do not shake the saw or the object that it is hanging from. Do not hang the saw from any electrical wires. Make sure that the structure used to hang the saw is secure. Personal injury or property damage may occur.
Only use the hook for hanging the saw. Using the hook to hang anything else could lead to serious injury.
Do not use the hook to reach another object or use the hook to support your weight in any situation.

OPERATING INSTRUCTIONS

To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc. can cause a short circuit.

If any parts are damaged or missing, do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.

Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious injury.

To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the tool when assembling parts, making adjustments, or cleaning the tool.

This band saw must be used only with the battery packs and chargers listed below:

FX0421
FX0431 FX0451
FLEX
FX0111|  |  |  |  |  |
FLEX

FX0321

| FLEX

FX0121

| FLEX

FX0331

| FLEX

FX0221

| FLEX

FX0341

| FLEX

FX0231

NOTICE : Please refer to the battery pack and charger manuals for detailed operating information.

APPLICATION
This heavy-duty band saw is designed for professional metal and plastics cutting applications.
DO NOT use under wet conditions or in presence of flammable liquids or gases.

LOCK-OFF BUTTON

Your tool is equipped with a lock-off button, located above the variable-speed trigger switch, to prevent the saw from being activated unintentionally.
To lock the trigger switch in the OFF position, depress the lock-off button from the side marked with ” ” (Fig. 8a).

To unlock the trigger switch, depress the lock-off button from the side marked with ” ” (Fig. 8b).

SPEED DIAL (FIG. 9)

The band saw has a speed dial located on the side of the handle to set the maximum speed.
Rotate the speed dial to “5” for maximum speed or to “1” for minimum speed.

To prevent the blade teeth damage, do not make any speed changes while the tool is running.
VARIABLE-SPEED TRIGGER SWITCH Your tool is equipped with a variable-speed trigger switch. The tool can be turned “ON” or “OFF” by depressing or releasing the trigger.
The variable-speed trigger switch delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure (Fig. 9)

PROPER HAND POSITION (FIG. 10)

To reduce the risk of serious personal injury, ALWAYS use proper hand position.
Proper hand position requires one hand on the main handle and one hand on the front handle.

GENERAL CUTTING

1. Remove the battery pack from the tool.
2. Make sure that the workpiece is firmly clamped in place to keep it from slipping or moving while cutting.
3. Install the appropriate type and size of blade for the workpiece material and size.
4. Mark the line of cut clearly on workpiece, if needed.
5. Attach the battery pack to the band saw.
6. Hold the saw firmly with both hands. Make sure to keep your hands on the insulated gripping areas only.
7. Bring the workpiece guide into contact with the workpiece while keeping the blade off of the workpiece.
8. Depress the lock-off button to the UNLOCKED position and squeeze the variable-speed trigger switch to start the saw and bring it to the maximum desired cutting speed before applying the blade to the workpiece.
9. Slowly and gently tilt the tool to bring the band saw blade into contact with the workpiece.
   Use only enough steady pressure on the blade to keep the saw cutting. Do not force
   the tool.

NOTICE: During cutting, if the band saw becomes locked or jammed in the workpiece material, release the switch immediately to avoid damage to the band saw blade and motor.

End pieces, which would be heavy enough to cause injury when they drop, after cut-off, should be supported. End pieces may be hot and sharp. Safety shoes and heavy gloves are strongly recommended.
To prevent the blade teeth damage, do not make any speed adjustment using the speed dial while the tool is running.

TIPS FOR BETTER CUTTING

• Start cutting on a surface where the greatest number of teeth will be in contact with the workpiece at one time (Fig. 11)
• Never twist the band saw blade during cutting operation.
• Never use liquid coolants with portable band saws. Use of liquid coolants will cause buildup on pulleys and reduce performance.
• If excessive vibration occurs during the cut, ensure that the material being cut is securely clamped down. If vibration continues, change the band saw blade.
  

MAINTENANCE

To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance.

SERVICE

Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause a serious hazard. We recommend that all tool service be performed by a FLEX Factory Service Center or Authorized FLEX Service Station.

GENERAL MAINTENANCE

When servicing, use only identical replacement parts. Use of any other parts could create a hazard or cause product damage. Periodically inspect the entire product for damaged, missing, or loose parts such as screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product until all missing or damaged parts are replaced. Please contact customer service or an authorized service center for assistance.

CLEANING

The tool may be cleaned most effectively with compressed dry air. Always wear safety goggles when cleaning tools with compressed air. Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.
Certain cleaning agents and solvents damage plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

PULLEY BRUSH (FIG. 12)

The pulley brush is located inside the saw housing next to the drive pulley and helps keep the blade clean of dust and chips. As the brush becomes worn, it will need to be adjusted or replaced.

1. Turn the band saw over and place it on a workbench or table with the front handle to the right.
2. Remove the left blade cover from the tool.
3. Loosen the screw that secures the pulley brush with a T20 Torx screwdriver (not included).
4. Position the pulley brush against the pulley.
5. Tighten the screw.
6. Snap the left blade cover into place. Ensure all cover snaps are properly seated.
   

STORAGE

Store the tool indoors in a place that is inaccessible to children. Keep away from corrosive agents.

ACCESSORIES

The use of any other accessories not specified in this manual may create a hazard.

FLEX 5-YEAR LIMITED WARRANTY

Chervon North America, Inc. (“Seller”) warrants to the original purchaser only, that all FLEX 24V products will be free from defects in material or workmanship for a period of five years from date of purchase when the original purchaser registers the product within 30 days from the date of original retail purchase and retains their receipt as proof of purchase. THE 5-YEAR LIMITED WARRANTY PERIOD IS CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE AND ONLY APPLICABLE TO FLEX 24V TOOLS, BATTERIES AND CHARGERS. If the original purchaser does not register their product within 30 days, the foregoing limited warranty will apply for a duration of three years. Product registration can be completed online at www.registermyflex.com.
24V Tools: 5-Year Limited Warranty with Registration
24V Batteries and Chargers: 5-Year Limited Warranty with Registration
Corded, 12V and 20V FLEX Legacy Products: 1-Year Limited Warranty, No Registration Benefit FLEX STACK PACK™ Storage System: 1-Year Limited Warranty with Registration
Functional Attachments FT161 and FT421: 5-Year Limited Warranty with Registration / 3-Year Limited Warranty without registration

Other Accessories and Attachments: No Warranty SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of parts, without charge, which are defective in material or workmanship and which have not been misused, carelessly handled, or repaired by persons other than a FLEX Authorized Service Dealer. This warranty does not cover part failure due to normal wear and tear. To make a claim under warranty, return the complete product, transportation prepaid, to any FLEX Authorized Service Dealer. For Authorized FLEX Service Dealers, please visit www.registermyflex.com or call 1-833-FLEX-496 (1-833-353-9496).
The 5-Year Limited Warranty does not apply to accessories, attachments or parts.
The 1-Year limited warranty for FLEX STACK PACK™ Storage System covers only tool boxes and does not apply to system attachments and power tool accessories.
Any implied warranties applicable to a product shall be limited in duration equal to the duration of the express warranties applicable to such product, as set forth in the first paragraph above. Some states in the U.S. and some Canadian provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply.
FLEX is not responsible for direct, indirect, incidental or consequential damages. Some U.S. states and Canadian provinces do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply. This limited warranty gives you specific legal rights, and you may also have other rights which vary by state in the U.S. and by province in Canada.
This limited warranty applies only to products sold within the United States of America, Canada and the commonwealth of Puerto Rico. For warranty coverage within other countries, contact your local FLEX dealer.

Customer Support

Chervon North America, 1203 E. Warrenville Rd., Naperville, IL 60563
www.flexpowertools.com
www.registermyflex.com
1-833-FLEX-496 (1-833-353-9496)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>