LOREX B463AJ Series 2K Battery Video Doorbell User Manual
- June 11, 2024
- Lorex
Table of Contents
LOREX B463AJ Series 2K Battery Video Doorbell
Package Contents
-
2K Battery Doorbell
-
Mounting Bracket
-
Horizontal Wedge 15°
-
Vertical Wedge 5°
-
USB Power Cable
-
Extension Wire
-
Connecting Wires (x2)
-
Release Pin
-
Anchors & Screws (x2)
-
1/4” Drill Bit
-
Wire Caps (x3)
Tools Needed
- Drill
- Screwdriver
Overview
- Release Tab
- USB Charging Port
- Reset Button*
- Power Terminals
- MicroSD Card Slot
- QR Code
- Speaker
- Camera
- IR Light
- PIR Sensor
- Light Sensor
- Microphone
- Status Indicator
- Call Button
- Night Light
***** Press and hold the reset button until you hear the audio prompts.
Status Indicator
|
Device initiating / Battery fully charged
---|---
|
Ready for network connection
|
Pairing to the Lorex Home account
|
Battery charging
|
Device Ready / Event detected
|
2-way talk
|
Call ongoing
|
Factory reset*
|
Network connection failed
|
Firmware update in progress
Device App Setup
- Download Lorex Home app.
-
Short press the reset button, and then wait for the audio prompts.
Note
If the status indicator does not start flashing blue, use the included USB power cable to power on your device, and then short press the reset button.
• Do not remove the USB power cable while connecting to the app. -
Tap in the app, and then follow the in-app steps to add your doorbell.
-
Choose either the Battery or Wired setup.
Battery Setup
-
Fully charge your Battery Doorbell before mounting. This could take up to 3 hours. 5V/2A power adapter is recommended (not included). Once fully charged, the status indicator will turn solid blue.
Recommendation
Charge your doorbell at the optimal environmental temperature of 32o F to 113o F (0o C to 45o C). The optimal operating temperature is -4o F to 122o F (-20o C to 50o C). -
Go to and complete the Mounting section.
-
Press the doorbell into the Mounting Bracket. You will hear a ‘click’ when it secures into place.
To remove your doorbell from the bracket, hold onto the doorbell, and then
insert the release pin into the hole on the Mounting Bracket until the release
tab is reached.
Wired Setup
TURN OFF THE POWER RUNNING TO YOUR EXISTING DOORBELL AT THE BREAKER.
Test that power has been disconnected by pressing the button on your existing
doorbell. There should be no sound.
8-24 VAC is required. If you do not have this voltage, you will need a 8-24
VAC doorbell transformer.
Always be careful when handling electrical wiring. If you are not comfortable
doing it yourself, consult a licensed electrician.
Wired Installation
- Remove your existing doorbell and disconnect the wiring.
Tip Bend the power cables so they do not fall through the wall.
-
Go to and complete the Mounting section.
-
Completely remove the power port terminal screws completely with a Philips-head screwdriver.
-
Thread the screws through the metal loops of the Connecting Wires, and then tighten the screws clockwise.
-
Align the ends of your existing wiring and Connecting Wires, place the wire caps over the exposed wiring, and then twist the wire cap clockwise to tighten.
If your existing doorbell wiring is too short, replace the Connecting Wires with the provided Extension Wire. -
Push the wiring back into the wall. Make sure there is enough space to fit the cable connectors and wire caps into the hole in the wall.
-
Press the doorbell into the Mounting Bracket. You will hear a ‘click’ when it secures into place.
-
Reconnect power to the doorbell at the breaker.
The doorbell’s optimal operating temperature is -4o F to 122o F (-20o C to 50o C). During colder and hotter seasons you may need to disconnect and charge the doorbell indoors.
Mounting
- Place the Mounting Bracket on the desired location with the arrow pointing up.
- Mark the holes for screws.
- Using a Phillips-head screwdriver and the provided screws, secure the Mounting Bracket to the surface.
Optional
Drill 1/4” (6mm) holes for the anchors.
Optional: Wedge Installation
Align and place either one of the horizontal or vertical wedges to the
Mounting Bracket according to the direction you want the doorbell to face.
To change the direction of the angle, flip the horizontal or vertical wedge upside down.
Horizontal Wedge
15° right
15° right
Vertical Wedge
5° down
5° up
Need help?
Scan the below QR code for the Quick Start Guide and additional support material.
Register your product
Please see our full Terms of Service and Limited Hardware Warranty Policy at: lorex.com/pages/warranty
Copyright © 2022 Lorex Technology Inc
As our products are subject to continuous improvement, Lorex reserves the
right to modify product design, specifications and prices, without notice and
without incurring any obligation. E&OE. All rights reserved
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two
conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>