sygonix 2729930 Digital Alarm Clock with Qi Charging Desk Instruction Manual
- June 11, 2024
- Sygonix
Table of Contents
- Intended use
- Delivery content
- Up-to-date operating instructions
- Description of symbols
- Safety instructions
- Components and controls
- Activating/replacing the battery
- Setup and connection
- Operation
- Cleaning and maintenance
- Disposal
- Declaration of Conformity (DOC)
- Technical data
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Operating instructions
Digital Alarm Clock with Qi Charging Desk
Item no. 2729930
Intended use
The product is an alarm clock with an additional charging function. It can
charge or power external devices via the USB output and charge devices that
comply with the Qi standard.
The product is intended for indoor use only. Do not use it outdoors. Contact
with moisture must be avoided under all circumstances.
Using the product for purposes other than those described above may damage the
product. Improper use can result in short circuits, fires, or other hazards.
This product complies with statutory, national and European regulations. For
safety and approval
purposes, you must not rebuild and/or modify the product.
Read the instructions carefully and store them in a safe place. Always provide
these operating instructions when giving the product to a third party.
All company and product names contained herein are trademarks of their
respective owners. All rights reserved.
Delivery content
- Digital alarm clock with Qi charging desk
- CR2032 button cell
- USB-C cable
- Operating instructions
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.
Description of symbols
| The symbol with an exclamation mark in a triangle is used to highlight
important information in these operating instructions.
Always read this information carefully.
---|---
| This symbol on the device tells the user to read these instructions
carefully before getting started and using the device.
| The Qi symbol indicates this is a Qi certified device.
Safety instructions
Read the operating instructions carefully and adhere in particular to the safety instructions. If you do not follow the safety information and information on proper handling in these operating instructions, we will assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.
5.1 General information
- This product is not a toy and should be kept out of reach of children. Only use the product out of the reach of children. The product contains small parts that could be swallowed and a battery.
- Do not leave packaging material lying around carelessly, as it could become a dangerous plaything for children.
- Should you have any questions or concerns after reading this document, please contact our technical support or a professional technician.
- Maintenance, modifications and repairs must be carried out by a technician or a specialist repair centre.
5.2 Handling
- Handle the product carefully. It can be damaged by impact, blows, or by being dropped, even from a low height.
5.3 Operating environment
- The product must not be exposed to high temperatures, moisture, humidity, strong vibrations or high mechanical stress.
- Never switch the device on immediately after taking it from a cold into a warm environment. This may cause condensation to form, which can destroy the product. Allow the product to reach room temperature before using it.
5.4 Operation
-
If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stress. -
Keep magnetic cards, such as credit cards, ID cards, etc., away from the device. The Qi charging pad can erase data on these cards or damage them.
-
Persons with medical implants, such as pacemakers or other medical devices, should keep a minimum distance of 20 cm from the Qi charging pad to prevent interference with these devices.
-
Consult an expert when in doubt about the operation, safety or connection of the device.
5.5 (Rechargeable) batteries
-
Always ensure that the polarity is correct when inserting (rechargeable) batteries.
-
Always remove (rechargeable) batteries when not in use for a long time to avoid damage from leakage. Leaking or damaged (rechargeable) batteries may cause acid burns if they come into contact with your skin. Therefore, use suitable protective gloves when handling damaged (rechargeable) batteries.
-
(Rechargeable) batteries must be kept out of reach of children. Do not leave (rechargeable) batteries lying around, as there is a risk that children or pets may swallow
them. -
(Rechargeable) batteries must not be dismantled, short-circuited or thrown into the fire. Never attempt to recharge non-rechargeable batteries. This may cause an explosion!
5.6 Connected devices
- Follow the operating and safety instructions of devices to be connected to this product.
- Be sure to use only power supply units that comply with the specifications in the “Technical data” to avoid malfunctions, overloads or long charging times.
Components and controls
1 Battery compartment
2 INPUT connection
3 SNOOZE button
4 OUTPUT connection
5 Charging indicator| 6 Qi charging pad
7 – button
8 + button
9 M button
---|---
Activating/replacing the battery
The alarm clock has a backup battery that saves the settings in the event of a
power failure.
The unit comes with a battery that has an insulating strip that protects the
battery from discharging.
Before using the alarm clock for the first time, remove the insulating strip
from the battery compartment (1).
You should change the battery if the alarm clock no longer saves data in the
event of a power failure.
- Remove the screw on the battery compartment (1).
- Lift off the cover and remove the discharged battery.
- Insert a new 3 V CR2032 button cell into the battery compartment with the positive pole facing outwards. Check that the button cell is properly engaged in the contact clip.
- Replace the cover and screw it back on.
Setup and connection
Make sure you position the device in a safe and stable place, away from objects that might fall on it, thereby avoiding unwanted accidents.
Note:
– Given the variety of paints and varnishes used to coat furniture, it cannot
be ruled out that the device’s feet could leave visible traces on furniture
due to a chemical reaction. Do not place the device on top of valuable
furniture without appropriate protection.
– Do not expose the product to direct sunlight, vibrations, dust, hot and cold
temperatures or damp environments. The device must not be placed next to
powerful transformers or motors.
- Place the device on a flat, level surface that can support its load.
- Plug the supplied USB cable into a suitable USB power supply. The power supply must match the voltage/current capacity specified in the “Technical data”.
→ The charging indicator (5) flashes twice, and the alarm clock enters standby mode.
Operation
Tip: Keeping the + button (8) or the – button (7) pressed during setup changes the value continuously.
9.1 Setting the time
- Press the M button (9) twice to change the time format (12h/24h display).
- Press the M button (9) once and use the + button (8) and the – button (7) to set the hour display.
- Press the M button (9) again and use the + button (8) and the – button (7) to set the minute display.
- Press the M button (9) again to finish setting the time.
9.2 Setting the alarm
-
Press and hold the + button (8) to enable or disable alarm 1.
-
Press and hold the – button (7) to enable or disable alarm 2.
→ When the alarm is enabled, the display shows a corresponding symbol. -
Press and hold the M button (9) and use the + button (8) and the – button (7) to set the hour display of alarm 1.
-
Press the M button (9) briefly and use the + button (8) and the – button (7) to set the minute display of alarm 1.
-
Press the M button (9) briefly and use the + button (8) and the – button (7) to set the hour display of alarm 2.
-
Press the M button (9) briefly and use the + button (8) and the – button (7) to set the minute display of alarm 2.
-
Press the M button (9) briefly to finish setting the alarm.
9.3 Enabling and disabling the alarm
- When alarm 1 sounds, briefly press the + button (8) to switch off alarm 1 for 24 hours.
- When alarm 2 sounds, briefly press the – button (7) to switch off alarm 2 for 24 hours.
- When the alarm sounds, press the SNOOZE button (3) to mute the alarm for 5 minutes. You can use this function repeatedly.
- Press and hold the + button (8) to shut off alarm 1 completely.
- Press and hold the – button (7) to shut off alarm 2 completely.
→ Unless the alarm is switched off, it will automatically switch off after 3 minutes.
9.4 Display brightness
You can adjust the display brightness (display off and 3 brightness levels).
- Press the + button (8) briefly in standby mode to turn up the brightness.
- Press the – button (7) briefly in standby mode to turn down the brightness.
9.5 Setting/displaying the calendar
- Press and hold the SNOOZE button (3) and use the + button (8) and the – button (7) to set the year.
- Press the SNOOZE button (3) briefly and use the + button (8) and the – button (7) to set the month.
- Press the SNOOZE button (3) briefly and use the + button (8) and the – button (7) to set the date.
- Press the SNOOZE button (3) briefly to finish setting the calendar.
- Press the SNOOZE button (3) briefly in standby mode to display the calendar.
9.6 Temperature display
- The display shows the room temperature at the top right in standby mode.
- Press the SNOOZE button (3) twice to toggle the temperature display between °C and °F.
9.7 Qi charging function
- Place the mobile phone on the Qi charging pad (6), as shown in the figure below.
- The charging indicator (5) lights up continuously during the charging process.
- When the mobile phone is fully charged, the charging indicator (5) goes out.
- A flashing charging indicator (5) indicates that the unit has detected a foreign object or an unsuitable mobile phone (FOD = Foreign Object Detection), and the charging process is aborted.
Important:
– Before charging, ensure the mobile phone complies with the Qi standard.
– Place your mobile phone centrally on the Qi charging pad (6) for the fastest
possible charging.
– Remove any metal cases from the mobile phone to ensure smooth charging.
9.8 USB output
Use the OUTPUT connection (4) to connect devices with a USB input for charging
or power supply.
Strictly observe the maximum load capacity of this output stated in the
“Technical data”.
The unit may be damaged if overloaded.
Cleaning and maintenance
Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical
solutions. They can damage the housing and can cause the product to
malfunction.
– Do not immerse the product in water.
- Disconnect the product from the power supply.
- Clean the product with a dry, lint-free cloth.
Disposal
11.1 Product
This symbol must appear on any electrical and electronic equipment placed on
the EU market. This symbol indicates that this device should not be disposed
of as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and
accumulators, which are not enclosed by the WEEE, as well as lamps that can be
removed from the WEEE in a non-destructive manner, must be removed by end
users from the WEEE in a nondestructive manner before it is handed over to a
collection point.
Distributors of electrical and electronic equipment are legally obliged to
provide free take-back of waste. Conrad provides the following return options
free of charge (more details on our website):
- in our Conrad offices
- at the Conrad collection points
- at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be
disposed of.
It should be noted that different obligations about the return or recycling of
WEEE may apply in countries outside of Germany.
11.2 Batteries/rechargeable batteries
Remove batteries/rechargeable batteries, if any, and dispose of them
separately from the product.
According to the Battery Directive, end users are legally obliged to return
all spent batteries/rechargeable batteries; they must not be disposed of in
the normal household waste.
Batteries/rechargeable batteries containing hazardous substances are labelled
with this symbol to indicate that disposal in household waste is forbidden.
The abbreviations for heavy metals in batteries are: Cd = Cadmium, Hg =
Mercury, Pb = Lead (name on (rechargeable) batteries, e.g. below the trash
icon on the left).
Used (rechargeable) batteries can be returned to collection points in your
municipality, our stores or wherever (rechargeable) batteries are sold. You
thus fulfil your statutory obligations and contribute to environmental
protection.
Batteries/rechargeable batteries that are disposed of should be protected
against short circuit and their exposed terminals should be covered completely
with insulating tape before disposal. Even empty batteries/rechargeable
batteries can contain residual energy that may cause them to swell, burst,
catch fire or explode in the event of a short circuit.
Declaration of Conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this product conforms to the 2014/53/EU directive.
- Click on the following link to read the full text of the EU declaration of conformity: www.conrad.com/downloads
Enter the product item number in the search box. You can then download the EU declaration of conformity in the available languages.
Technical data
USB power supply …………………… 5 V/3 A, 9 V/3 A, 12 V/2 A
Qi charger capacity ………………….. max. 15 W
USB A output ………………………….. max. 5 V/1 A
Backup battery ………………………… 3 V CR2032 button cell
Charging efficiency ………………….. min. 73%
Transmission range …………………. max. 8 mm
Transmission frequency……………. 110.6 – 136.2 kHz
Transmission power…………………. -9,64 dBµA/m @ 10 m
Dimensions …………………………….. 141 x 68 x 125 mm
Weight …………………………………… 158 g
Ambient conditions ………………….. 0 – 45 °C / 20 – 85% rel. humidity
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g.
photocopy, microfilming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is
prohibited.
This publication represent the technical status at the time of printing.
Copyright 2023 by Conrad Electronic SE.
*2729930_V1_0223_02_VTP_m_EN
http://www.conrad.com/downloads
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>