KOHLER K-1263840 Amplifier Installation Guide

June 6, 2024
Kohler

KOHLER K-1263840 Amplifier

Specifications

Tools and Materials

Before you Begin

WARNING: Risk of electric shock. Disconnect power before servicing.

CAUTION: Risk of product damage. The amplifier is rated to operate in temperatures up to 104°F (40°C). Do not install near heat sources (such as radiators or heat registers) or in any location where the temperature may exceed 104°F (40°C).
CAUTION: Risk of product damage. A network cable is provided with this product. For all bath installations with combined user experiences, you must use the supplied cable in place of the cable shipped with the bath. Failure to do so may cause irreparable damage to the amplifier.

NOTICE: This product is not water-resistant. Do not install in a location where excessive moisture, high humidity levels, or condensation are present.
NOTICE: Follow all electrical and building codes.
NOTICE: Provide unrestricted service access to the amplifier.
NOTICE: Provide a minimum of 611 (152 mm) of space around the amplifier for proper air flow.

  • Determine amplifier and speaker locations before beginning installation. Test the BLUETOOTH® range between the amplifier and your wireless device when determining amplifier location. Under normal conditions, the maximum range is 30′ (9.14 m).
  • The amplifier can be mounted in any orientation. Use the supplied brackets or rubber feet to accommodate your mounting configuration.
  • Locate the amplifier within close proximity to a 15 A 120 V electrical outlet. Install a GFCI or RCD electrical outlet within the stud framing and within 24″ (610 mm) of the amplifier.
  • A qualified electrician should install an electrical outlet.
  • Install the electrical outlet prior to installing the amplifier.
  • This amplifier complies with CE, FCC, IC, and RoHS.

Preparation

NOTE: To play your personal music files, a wireless BLUETOOTH device or a device with a 3.5 mm stereo cable connection is required.

  • Plan the location of the amplifier to allow access to the front and back ports.
  • Allow adequate reach for wires between the bath and the amplifier.
  • Make sure the status LED will be visible after installation.

NOTICE: The circular auxiliary-in port is not an Ethernet communication port. Do not connect an Ethernet network to the auxiliary-in port. Use the auxiliary-in port only for a standard accessory.

Installation

CAUTION: Risk of product damage. The amplifier is rated to operate in temperatures up to 104°F (40°C). Do not install near heat sources (such as radiators or heat registers) or in any location where the temperature may exceed 104°F (40°C).
NOTICE: Mount the amplifier in a dry location, and provide a minimum of 6″ (152 mm) of space for proper air flow.
NOTE: Choose the mounting location to best suit the location of the incoming transducer wires and other cables.
NOTE: Make sure the status LED will be visible after installation.

Mounting Options

  • Wall-mount: Secure the amplifier in an upright position using the mounting brackets, anchors, and short screws provided.
  • Cabinet-mount: Secure the amplifier in an upright position using the mounting brackets and short screws provided.
  • Surface-mount: Attach the four rubber feet to the underside of the amplifier to protect against scratching your shelf or countertop surface.
  • Under-mount: Secure the amplifier in position using the mounting brackets and short screws provided.

Bracket Installation

  • Position the amplifier with attached brackets in the desired location.
  • Mark the bracket hole locations with a pencil.
  • Drill pilot holes or insert anchors as needed at the marked locations.
  • Secure the brackets using the four screws provided.

Amplifier Connection

CAUTION: Risk of product damage. Use the network cable provided with the amplifier for installation with baths having more than one user experience (whirlpool, vibracoustic, air bath, etc.). For these installations, remove and discard the network cable assembled to the bath, and replace it with the new network cable. Failure to replace the network cable may cause irreparable damage to the amplifier.
IMPORTANT! A network cable is provided with this product. Depending upon the type of bath product being installed, use this cable to connect the amplifier and user interface, or to connect the bath and user interface. Refer to the bath Homeowners Guide or the bath product page on kohler.com to determine the bath type being installed.
NOTE: The transducer terminals and wires are numbered to identify the correct connections. When required, the amplifier can be removed to aid in the wire connection process.
NOTICE : The circular auxiliary-in port is not an Ethernet communication port. Do not connect an Ethernet network to the auxiliary-in port. Use the auxiliary-in port only for a standard accessory.

  • Disconnect the power from the amplifier.
    If equipped, connect the chromatherapy connector from the bath to the chromatherapy connection on the amplifier.

  • Connect the transducer wires to the transducer terminals on the amplifier. The white wires with black stripes are connected to the positive ( +) terminals, and the solid white wires are connected to the negative (-) terminals.

  • Connect the clear connector of the user interface cable to the amplifier user interface connection.

  • If used, connect the auxiliary-in cable to the auxiliary-in port on the amplifier.

  • Reconnect the power to the amplifier.

  • Verify that the status LED turns on.

Operation

  • When using the auxiliary-in, set your music device to midrange volume after connecting to the amplifier, but before sending an audio signal from the device.
  • To listen to a BLUETOOTH source, go to the AUX screen of the user interface. Activate by pressing the AUX icon.
  • A wireless BLUETOOTH source will override an auxiliary-in source.
  • When listening to an auxiliary-in source, a tone will be heard when a BLUETOOTH device is paired with the amplifier. The tone indicates that the auxiliary-in source is no longer active.
  • To listen to an auxiliary-in source, the BLUETOOTH source must be un-paired from the amplifier.
  • When listening to a BLUETOOTH device which is paired with the amplifier, a tone will be heard when the BLUETOOTH device has unpaired from the amplifier and is no longer active.

Status LED Light

  • Yellow blink = Amplifier error: Contact the Customer Care Center.
  • Blue blink= Stand-by mode: Normal operation – No BLUETOOTH connection.
  • Blue solid = Normal operation: BLUETOOTH receiver is paired with a device.
  • Green blink = User interface error – For example, loose or disconnected cable.

3.5 mm Stereo Input

  • A wired audio device can be connected to the auxiliary-in port on the amplifier.
  • Audio input may be slightly delayed when a device is initially connected.

Wireless Input

  • Once a BLUETOOTH device is paired, the LED will be solid blue and the audio input will fade-in.
  • On the BLUETOOTH user device, the amplifier will display as “VibrAcoustic.”
  • If a BLUETOOTH pin number is required, use “0000.”

NOTE: For more information on system operation, refer to the Homeowners Guide.

Troubleshooting

IMPORTANT! Turn off the power supply before performing any maintenance.
NOTE: For service parts information, visit your product page at kohler.com/ serviceparts. This troubleshooting guide is for general aid only. For service and installation issues or concerns, call 1-800-4KOHLER.

Compliance

Contains: Kohler Company, Model: 1263840, FCC ID: N82KOHLER017, IC: 4554A- KOHLER017, CE: CE2200

FCC Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

The circular auxiliary-in port is not an Ethernet communication port. Do not connect it to an Ethernet network.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3(B) /NMB-3(B)
CE2200

FCC and IC Radiation Exposure Statement for Mobile Devices
This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 7-7 /8″ (200 mm) between the radiator (amplifier) and your body. The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Range and Function Disclaimer
BLUETOOTH® is the name for a short-range radio frequency (RF) technology that operates at 2.4 GHz. The effective range of most BLUETOOTH mobile devices is 10 meters. BLUETOOTH is designed for very low power use. The compatibility of the BLUETOOTH amplifier interface to mobile/portable devices differs according to the various individual devices and, in particular, may vary with different software versions for a device. The normal mobile device BLUETOOTH range can be up to 10 meters, however, placement of your mobile device and the BLUETOOTH amplifier’s installation environment will impact your reception range.
Water and walls can act as blocking agents to the BLUETOOTH signal that your mobile device is using to broadcast to your BLUETOOTH amplifier. Therefore, selecting an installation location that removes these range blocking obstacles will increase the effective range and performance of your BLUETOOTH amplifier.

You can test your BLUETOOTH reception by performing simple range tests using your mobile device prior to performing a permanent installation. The best way to make use of the short BLUETOOTH range is to make sure your BLUETOOTH amplifier is as close to the BLUETOOTH transmitter (mobile phone, tablet, etc.) as possible. The less distance between the two devices, the greater will be the reliability of your BLUETOOTH audio signal, and the less distance means less obstacles in the medium through which the transmission is passing, so there is a reduced chance of audio signal loss.

The compatibility of the BLUETOOTH amplifier to mobile/portable devices differs according to the various individual devices and, in particular, may vary with different software versions for a device. All functions are based on industry-wide communications standards. Compatibility between the BLUETOOTH amplifier and mobile device is therefore largely dependent upon the software version of the mobile device. Other factors (e.g. installation location, walls, distance) mean that in individual cases, sporadic impairment of functions may occur in devices that otherwise function reliably. Not all functions are supported in all countries.
Because of these reasons, Kohler Co. can assume no guarantee for the unlimited compatibility and functionality of your mobile device in conjunction with the BLUETOOTH amplifier.

The BLUETOOTH® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Kohler Co. approved suppliers is under license. Other trademarks and trade names are those of their respective owners.

Warranty

ONE-YEAR LIMITED WARRANTY
KOHLER plumbing products are warranted to be free of defects in material and workmanship for one year from date of installation.
Kohler Co. will, at its election, repair, replace or make appropriate adjustment where Kohler Co. inspection discloses any such defects occurring in normal usage within one (1) year after installation. Kohler Co. is not responsible for removal or installation costs. Use of in-tank toilet cleaners will void the warranty.

To obtain warranty service contact Kohler Co. either through your Dealer, Plumbing Contractor, Home Center or E-tailer, or by writing Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler, WI 53044, USA, or by calling 1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada, and 001-800-456-4537 from within Mexico, or visit www.kohler.com within the USA, www.ca.kohler.com from within Canada, or www.mx.kohler.com in Mexico.

IMPLIED WARRANTIES INCLUDING THAT OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. KOHLER CO. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of special, incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from state/province to state/province.
This is Kohler Co.’s exclusive written warranty.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals