NEOUSYS Nuvo-9531 Intel 13th/12th-Gen Compact Fanless Computer Installation Guide

NEOUSYS Nuvo-9531 Intel 13th12th-Gen Compact Fanless Computer

Warning

• Only qualified service personnel should install and service this product to avoid damage or injury.
• Observe all ESD procedures during installation to avoid damaging t he equipment.

Preparing tools

Unpack the equipment and make sure the following tools are available and delivered contents are correct.

User-provided tools

• Anti-static wrist wrap

Packing List

Item

| Description|

Quantity

---|---|---

01

| Nuvo-9531 system| 1
02| CPU bracket|

1

03

| Wall-mount bracket| 2
04| Drivers & utilities disc|

1

05

| 3-pin pluggable terminal block| 1
06| Screw pack|

1

Overview – Front Panel

No.

| Item|

Description

---|---|---

1

|

Power Button

| Use this button to turn on or shutdown the system.

2

|

System status LEDs

| Four system LEDs, power (PWR), watchdog timer (WOT), hard disk drive (HDD) and ignition (IGN).

3

|

Reset button

| Use this button to manually reset the system.

4

|

2.5G Ethernet Port (optional PoE+l

| The 2.5G Ethernet ports support 10/ 100/ 1000/ 2500 Mbps (optional PoE+l network connections with optional PoE+.

5

|

Dis12layPort

| Support display resolutions up to 4096 x 2304_ Compatible with HDMI/ DVI via respective adapter cable (resolution may vary).

6

|

USB3.2 Gen1 Ports

| USB 3.2 Gen1 port supports up to 5 Gbit/s data transfer bandwidth.

7

|

CMQS Reset Button

| Use this button to manually reset the CMOS.
Ar e a In r e d| 2.5″ HOD/ SSD hot swappable tray

Power Button

The power button is a non-latched switch for ATX mode on/off operation. To turn on the system, press the power button and the PWR LED should light-up green. To turn off the system, issuing a shutdown command in OS is preferred, or you can simply press the  power button. To force shutdown when the system freezes, press and hold the power button for 5 seconds. Please note that there is a 5-second interval between on/off operations (i.e. once the system is turned off, there is a 5-second wait before you can power-on the system).

System Status LED

There are four LED indicators on the I/O panel: PWR (power), WDT (Watchdog timer), HDD (hard disk drive), IGN (ignition power control, an optional feature). The descriptions of these four LED are listed in the following table.

Indicator

| Color|

Description

---|---|---

PWR

| Green| Power indicator, lighted-up when system is on.
WDT| Yellow|

Watchdog timer LED, flashing when watchdog timer Is started.

HOD

| Red| Hard drive indicator, flashing when hard drive is active.
IGN| Green|

An optional feature. Ignition signal indicator, lid when IGN is high (12V/ 24V).

Reset Button

The reset button is used to manually reset the system in case of system halt or malfunction. To avoid unexpected reset, the button is purposely placed behind the panel. To reset, please use a pin-like object (eg. tip of a pen) to access the reset button.

2.5G Ethernet Port (Optional PoE+)

The system offers four 2.5Gb Ethernet ports using Intel® I226 controller, and each port each come with screw-lock mechanism (indicated in ). When plugged in and connected via the Ethernet cable, the LEDs on the RJ45 connector indicate connection status and speed.

The optional Power over Ethernet (PoE) supplies electrical power and data on a standard CAT-5/CAT-6 Ethernet cable. Acting as a PoE PSE (Power Sourcing Equipment), compliant with IEEE 802.3at, each PoE port delivers up to 25W to a Powered Device (PD). The system has a total 100W power budget. PoE ports can automatically detect and determine if the connected device requires power or not, so it is compatible with standard Ethernet devices as well.

Active/link LED

LED Color

|

Statu s

|

Description

---|---|---

Orange

|

Off

|

Ethernet port is disconnected

On

|

Ethernet port is connected and no data transmission

Flashing

|

Ethernet port is connected and data is transmittina/receiving

Speed LED

LED Color

| Status|

Description

---|---|---

Green or Orange

|

Off

| 10 Mbps
Green|

100 Mbps

Orange

|

1000/ 2500 Mbps

DisplayPort

The system has a DisplayPort (DP) output which is a digital display interfaces that mainly connect video source and carry audio to a display device. When connecting a DP, it can deliver up to 4K UHD (4096 x 2304) in resolution. The system is designed to support passive DP adapter/ cable. You can connect to other display devices using DP-to-HDMI cable or DP-to-DVI cable.

With the VGA output on the rear panel, the system supports dual independent display outputs. To support dual display outputs and  achieve best VGA/ DisplayPort output resolution in Windows, you need to install corresponding graphics drivers.

USB3.2 Gen1 Port

The system offers four USB 3.2 Gen1 (SuperSpeed USB) ports on its front panel with screw-lock mechanism. They are backward compatible with USB 2.0, USB 1.1 and USB 1.0 devices. UEFI USB is also supported so you can use USB keyboard/ mouse in UEFI shell environment. USB 3.2 Gen1 driver is supported natively in Windows 10. The screw-lock mechanism is available on the three ports indicated in blue and red ,  and due to the width of the screw-lock connector, only the USB ports indicated in red can be connected simultaneously when using the screw-lock mechanism.

Note
Depending on the design of your screw-lock USB connector, the CMOS reset button may be obstructed if the USB pot below is connected.

CMOS Reset Button

The CMOS Reset button is used to manually reset the motherboard BIOS in case of system halt or malfunction. To avoid unexpected operation, it is purposely placed behind the panel. To reset, please use the tip of a pen, press and hold for at least 5 seconds to reset the BIOS.

2.5” HDD/ SSD Hot-swappable Tray

The system features an external hot-swappable 2.5″ hot-swappable tray that supports a 7mm 2.5″ HDD/ SSD. Designed for easy access, the HDD tray is secured by a lock (indicated in red).

Overview – Rear Pane

No .| Item|

Description

---|---|---

1

| 3-Qin Terminal Block DC lnput
Optional lgniti2n Power Control}| Compatible with DC power input from 8~48V, the terminal block Is also used for 1gnit 1on signal input.

2

| USB2.0 Ports| The USB 2.0 ports are backward with USB 1.1 / 1.0

3

| COM2/3/4 Port| Can be configured as:
CO M 2 : single RS-422/ 485 port
CO M2 / COM3/ COM4 · three 3-wire RS-232 ports

4

| COM1 port| Software programmable RS-232/ 4221485 port .

5

| VGA Port| VGA output supports resolution up to 1920×1200@60Hz

6

| 4-Pole 3 5mm| The 4-pole 3.5mm jack accepts microphone voice input and headphone speaker sound output
Microi:2hone – in / Speaker out Jack

7

| DIO Port| The port provides four DI and four DO via DB15 female connector

3-pin Terminal Block for DC, Remote ON/ Off, and Optional Ignition Power

Control

The system accepts a wide range of DC power input from 8 to 48V via  a 3-pin pluggable terminal block, which is fit for field usage where DC power is usually provided. The screw clamping mechanism on the  terminal block offers connection reliability when wiring DC power.

The Remote On/ Off connection allows for external switch extension. It is useful when the system is placed in a cabinet or a not easily accessed location.

In addition to DC power input and Remote On/ Off, this terminal block can also accept optional ignition signal input (IGN) for in-vehicle applications.

Warning

Please make sure the voltage of DC power is correct before you connect it to the system. Supplying a voltage over 48V will damage the system.

USB2.0 Port

The USB2.0 ports are implemented via native xHCI (eXtensible Host Controller Interface) in the Intel 600 chipset and are backward compatible with USB 1.1 and USB 1.0 devices. UEFI USB support is also provided so you can use USB keyboard/ mouse in UEFI shell environment. xHCI driver is supported natively in Windows 10, therefore you do not need to install xHCI driver to utilize USB functions.

COM2/3/4 Port

The port s it 3 provide up to 921600 bps baud rate, can be configured in the BIOS as single RS-422/ 485 port (COM2) or three 3-wire RS-232 ports (COM2/ / 4). An optional 1-to-3 Y-cable is available to connect three RS-232 devices.

**COM2/3/4Pin

**

The following table describes the pin definition of the COM port

|

3-port RS-232 COM21 3/4

---|---

Pin#

| COM2| COM3|

CO M4

1

| | |

2

|

RX

| |

3

|

TX

| |

4

| |

TX

|

5

|

GND

| GND|

GND

6

| |

RX

|

7

| | |

TX

8

| | |

RX

9

| | |

1-to-3-Ycable

| Single port RS – 4221 485 COM2
---|---

Pin#

| RS-422|

RS-485

1

| |
2| TxD+|

TxD+I RxD+

3

| RxD+|
4| RxD-|

5

| GND|

GND

6

| |
7| |

8

| TxD-| TxD-/ RxD-
9| |

COM1 Port

The port provides up to 921600 bps baud rate, it is a software-configurable RS-232/422/485 port via 9-pin D-Sub male connector. The operation mode, slew rate and termination of COM1 can be set in BIOS setup utility. The following table describes the pin definition of COM ports.

| COM 1
---|---
Pin#| RS -232 Mode| RS-422 Mode|

RS-485 Mode

1

| DCD| |
2| RX| 422TXD+|

485 TXD+/RXD+

3

| TX| 422 RXD+|
4| DTR| 422 RXD-|

5

| GND| GND| GND
6| | |

8

| CTS| 422 TXD-| 485 TXD–/RXD-
9| RI| |

VGA Port

VGA connector is the most common video display connection. The VGA output supports up to 1920×1200@60Hz resolution.

With the DisplayPort on the front panel, the system supports dual independent display outputs. To support dual display outputs and achieve best VGA/ DisplayPort output resolution in Windows, you need to install corresponding graphics drivers.

Note
Please make sure your VGA cable includes SDA and SCL (DDC clock and data) signals for correct communication with monitor to get resolution/timing information. A cable without SDA/ SCL can cause blank screen on your VGA monitor due to incorrect resolution/timing output.

4-Pole 3.5mm Microphone-in/ Speaker-out Jack

There is a female 4-pole audio jack for headphone (speaker) output and microphone input. To utilize the audio function in Windows, you need to install corresponding drivers.

DIO Port

The digital input (DI) and digital output (DO) function provides four digital input and four digital output on the rear panel of the system via DB15 female connector.

Isolated Digital Input

No. of Channel|

4-CH Isolated Digital Input Channels

Logic Level

| Logic High : 5 to 24V

Logic Low: O to 1.5V

Isolated Voltage|

2500 Vrms

Input Resistance

| 1k
Input Resistance|

Polling

Iso l ated Digital Output

No. of Channel

| 4-CH Isolated Digital Output Channels
Sink Current (per channel)|

500mA

Isolated Voltage

| 1500 Vrms
Operation Mode|

Polling

Pin   Definition

Pin#

|

Pin Def in it i on

---|---

1

| DI 0
2|

DI 1

3

| DI GND
4|

DO_GND

5

| DO 0
6|

DO 1

7

| DO – GND
8|

VDD

9

| DI GND
10|

DI 2

11

| DI 3
12|

DO_GND

13

| DO 2
14|

DO – 3

15

|

–

* When using DO0 ~ DO3, DOGND is the ground should be used.

Documents / Resources

| NEOUSYS Nuvo-9531 Intel 13th/12th-Gen Compact Fanless Computer [pdf] Installation Guide
Nuvo-9531 Intel 13th 12th-Gen Compact Fanless Computer, Nuvo-9531, Intel 13th 12th-Gen Compact Fanless Computer, Compact Fanless Computer, Fanless Computer, Computer
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>