NEOUSYS SEMIL-1700 Series Extreme Rugged Computer Installation Guide

June 9, 2024
NEOUSYS

NEOUSYS logo SEMIL-1700 Series
Quick Installation Guide

SEMIL-1700 Series Extreme Rugged Computer

Warning

  • Only qualified service personnel should install and service this product to avoid injury.
  • Observe all ESD procedures during installation to avoid damaging the equipment.

Preparing tools

Unpack the equipment and make sure the following tools are available and delivered contents are correct before you begin the installation procedure.
1-1. User-provided tools
• Anti-static wrist wrap
1-2. Packing List

Item Description Quantity
1 SEMIL 1700 series system  1
2 Drivers & utilities disc 1

Overview

NEOUSYS SEMIL 1700 Series Extreme Rugged Computer - fig
2

No. Item Description
1 DC input 8V to 48V DC input (M12 S-coded)
2 PoE+ GbE ports The M12 X-coded Power over Ethernet (PoE) ports provide

both data connection and electric power to devices (eg. IP camera).
SEMIL -1704| lx IEEE 802.3at GbE+ port via Intel® 1219
3x IEEE 802.3at GbE+ port via Intel® 1210
SEMIL -1714J
SEMIL – 1708| lx IEEE 802.3at GbE+ port via Intel® 1219 7x IEEE 802.3at GbE+ port via Intel® 1210
SEMIL – 1718J
3| USB 2.0 port| The USB 2.0 ports are backward-compatible with USB 1.1 / 1.0.
SEMIL -1704| 2x USB2.0 (M12 A-coded)
 SEMIL -1714J
SEMIL – 1708| 4 x USB2.0 (M12 A-coded)
SEMIL – 1718J
4| VGA port| VGA output supports resolution up to 1920×1200@60Hz
5| Audio port| SEMIL-17041 1714J: Not applicable
SEMIL-1714J/ 1718J: lx mic-in and speaker-out (M12 A-coded)
6| COM ports| COM 1 & 2 are RS-232 ports via an M12 A-coded connector
7| Power
button| Use this button to turn on or force shutdown the system.

DC-IN

NEOUSYS SEMIL 1700 Series Extreme Rugged Computer - fig
4

Warning
Please make sure the voltage of DC power is correct before you connect it to the system. Supplying a voltage over 48V will damage the system.

NEOUSYS SEMIL 1700 Series Extreme Rugged Computer - fig
5

Signal| M12 panel side| M12 cable connector end| Wire color
---|---|---|---
V+| 3| 3|
GND| 2| 2|
V+| 1| 1|
GND| PE| PE|

PoE+ Gigabit Ethernet Port

NEOUSYS SEMIL 1700 Series Extreme Rugged Computer

The number of ports for each SEMIL-1700 model variant is listed below:

PoE+ ports Model No. Port description
SEMIL -1704 x IEEE 802.3at GbE+ port via Intel® 1219 7x IEEE 802.3at GbE+

port via Intel® 12100
SEMIL -1714J
SEMIL — 1708| lx IEEE 802.3at GbE+ port via Intel® 1219 3x IEEE 802.3at GbE+ port via Intel® 121l
SEMIL — 1718J

NEOUSYS SEMIL 1700 Series Extreme Rugged Computer -
fig

Signal M12 panel side M12 cable connector end Wire color
LAN PO 1 1
LAN NO 2 2
LAN P1 3 3
LAN N1 4 4
LAN P3 5 5
LAN N3 6 6
LAN N2 7 7
LAN P2 8 8

USB Port

NEOUSYS SEMIL 1700 Series Extreme Rugged Computer - fig
3

Signal M12 panel side M12 cable connector end Wire color
D1+ 1 1
D1- 2 2
VCC_USB 3 3
GND 4 4
GND 5 5
VCC_USB 6 6
D2- 7 7
D2+ 8 8

VGA Port

NEOUSYS SEMIL 1700 Series Extreme Rugged Computer - fig
6

Signal M12 panel side M12 cable connector end Wire color
Red 1 1
GREEN 9 9
BLUE 7 7
GND 6 6
GND 8 8
GND 10 10
GND 12 12
GND 13 13
GND 14 14
GND 11 11
GND 16 16
GND 15 15
P5V VGA 17 17
VGA SDA 5 5
1-1SYNC CN 3 3
VSYNC CN 2 2
VGA SCL 4 4

Audio Port

NEOUSYS SEMIL 1700 Series Extreme Rugged Computer - fig
7

Signal M12 Socket end M12 cable side
Left channel 4 4
Right channel 5 5
Microphone 7 7
Ground 8 8

Port COM

NEOUSYS SEMIL 1700 Series Extreme Rugged Computer - fig
8

The system provides two COM ports via an M12 A-coded connector for communicating with external devices. These COM ports are 3-wire RS232 specifications and provide up to 115200 bps baud rate.
Pin Definition

Signal| M12 panel side| M12 cable connector end| Wire color
---|---|---|---
TXD1| 1| 1|
RXD1| 2| 2|
NC| 3| 3|
PWR_IGN| 4| 4|
GND| 5| 5|
NC| 6| 6| x
RXD2| 7| 7|
TXD2| 8| 8|

Power Button

NEOUSYS SEMIL 1700 Series Extreme Rugged Computer - fig
10

The power button is a non-latched switch for ATX mode on/off operation. To turn on the system, press the power button and the PWR LED should light-up green. To turn off the system, issuing a shutdown command in OS is preferred, or you can simply press the power button. To force shutdown when the system freezes, press and hold the  power button for 5 seconds. Please note that there is a 5-second interval between on/off operations (i.e. once the system is turned off, there is a 5-second wait before you can power-on the system).

NEOUSYS logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

NEOUSYS User Manuals

Related Manuals