HOME DECORATORS COLLECTION 1006152680 Pembroke Electric Fireplace User Guide

1006152680/316091779/28WM20532-16013
1006152692/316091773/28WM20532-16014

USE AND CARE GUIDE
PEMBROKE ELECTRIC FIREPLACE

QUESTIONS, PROBLEMS, MISSING PARTS? BEFORE RETURNING TO THE STORE,
CALL HOME DECORATORS COLLECTION CUSTOMER SERVICE
MONDAY – FRIDAY 8 A.M. – 7 P.M. EST, AND SATURDAY 9 A.M. – 6 P.M. EST.
1-800-986-3460
HOMEDEPOT.COM/HOMEDECORATORS

THANK YOU
We appreciate the trust and confidence you have placed in the Home Decorators Collection through the purchase of this Fireplace. We strive to
continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Home Decorators Collection!

Maximum Load Warning

CAUTION : This unit is intended for use only with the products and maximum weights indicated. Use with other products or products heavier than the maximum weights indicated may result in instability causing possible injury.

Safety Information

Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product, please call the customer
service at 1-800-986-3460, Monday- Friday 8 A.M. – 7 P.M. EST, and Saturday 9 A.M. – 6 P.M. EST.

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons including the following:

1. Read all instructions before using this appliance.
2. If possible, always unplug this appliance when not in use.
3. Only a qualified service person should repair this product.
4. Do not use outdoors.
5.  Do not cover the cord under the carpeting. Do not cover with throw rugs, runners or the like. Arrange the cord away from traffic areas and where it will not be tripped over.
6. To disconnect this appliance, turn the controls to the off position, and then remove the plug from the outlet.
7. Connect to properly grounded outlets only.
8.  This appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the current CSA C22.1 Canadian Electrical Code. For U.S.A. installations, follow local codes and the National Electrical Code, ANSI/NFPA NO.70.
9. This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. This fireplace should not be used as a drying rack for clothing. Do not hang Christmas stockings or other decorations on or near this product.
10.  There is a thermostat limiter inside the heater. When inner temperature overheating or abnormal heating occurs, the thermostat protective device will cut off the power supply to avoid damage to the fireplace or the risk of fire.

DANGER : High temperatures may be generated under certain abnormal conditions. Do not partially or fully cover or obstruct the front of this heater.
WARNING : In order to avoid overheating, do not cover the heater.
WARNING : If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
WARNING : Under no circumstances should this fireplace be modified. Parts that must be removed for servicing must be replaced prior to operating this fireplace again.
WARNING : This heater may include a visual alarm to warn that parts of the heater are getting excessively hot. If the alarm illuminates, immediately turn the heater off and inspect for any objects on or adjacent to the heater that may have blocked the airflow or otherwise caused high temperatures to have occurred. DO NOT OPERATE THE HEATER WITH THE ALARM ILLUMINATING.
WARNING : This appliance is not a toy. Supervise children playing near it.
WARNING : Use extreme caution when operating a heater near children and the disabled.
WARNING : This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate this appliance where it may fall into a bathtub or other water container.
WARNING : Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the appliance.
WARNING : To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where the opening may become blocked.
WARNING : Use this appliance only as described in the manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons.
WARNING : This appliance has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint or flammable liquids are used or stored. This fireplace should not be used as a drying rack for clothing. Do not hang Christmas stockings or other decorations on or near this product.
CAUTION : Never leave the heater operating unattended. Extreme caution is necessary if unsupervised children or invalids are nearby.
CAUTION : Before assembly, carefully use scissors or a utility knife to cut and unwrap all parts. Make sure you do not discard the hardware.

NOTE : Use care in assembling your new fireplace. Take your time and use the hardware provided and a quality Phillips head screwdriver. Never overtighten bolts.

• Do not sit on any part of the mantel.
• It is recommended to work on a soft surface like a rug or to lay out a blanket to protect the furniture from getting scratched during the assembly process.

NOTE : To avoid injury from unexpected starting or electrical shock, do not plug the power cord into a source of power during unpacking and assembly. The cord must remain unplugged whenever you are adjusting/assembling the fireplace. If any part is missing or damaged, do not attempt to use or plug in the power cord until the missing or damaged part is correctly replaced. To avoid electric shock, use only identical replacement parts when servicing double-insulated tools.
NOTE:
SAVE THESE
INSTRUCTIONS

Warranty

1 Year Limited Warranty: The manufacturer warrants that your new Electric Fireplace is free from manufacturing and material defects for a period of one year from the date of purchase, subject to the following conditions and limitations.

1. Install and operate this appliance in accordance with the installation and operating instructions furnished with the product at all times. Any unauthorized repair, alteration, willful abuse, accident, or misuse of the product shall nullify this warranty.
2. This warranty Is non-transferable and is made to the original owner, provided that the purchase was made through an authorized supplier of the product.
3. The warranty is limited to the repair or replacement of part(s) found to be defective in material or workmanship, provided that such part(s) have been subjected to normal conditions of use and service after said defect is confirmed by the manufacturer’s inspection.
4.  The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by refunding the wholesale price of the defective part(s).
5.  Any installation, labor, construction, transportation, or other related costs/expenses arising from defective part(s). repair, replacement, or otherwise of same, will not be covered by this warranty, nor shall the manufacturer assume responsibility for same.
6. The owner/user assumes all other risks, it any, including the risk of any direct, indirect or consequential loss or damage arising out of the use, or inability to use the product, except as provided by law.
7. All other warranties — expressed or implied — with respect to the product, its components, and accessories, or any obligations/liabilities on the part of the manufacturer are hereby expressly excluded.
8. The manufacturer neither assumes nor authorizes any third party to assume on its behalf, any other liabilities with respect to the sale of the product.
9. The warranties as outlined within this document do not apply to non-accessories used in conjunction with the installation of this product.
10. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

This warranty is void if:
a. The fireplace is subjected to prolonged periods of dampness or condensation.
b. There is any unauthorized alteration, willful abuse, accident, or misuse of the product.
c. You do not have the original receipt of purchase.

Pre-Assembly

HARDWARE INCLUDED

NOTE : Hardware not shown to actual size.

PRODUCT SPECIFICATIONS

PLANNING ASSEMBLY
Before beginning the assembly of the product, make sure all parts are present. Compare parts with Hardware Included and Package Contents lists.
If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts.
Estimated Assembly Time: 15 Minutes

TOOLS REQUIRED
Phillips Screwdriver

PACKAGE CONTENTS

Assembly

1 Unpacking the fireplace insert
Using scissors, cut the rope securing the fireplace insert.

• When the Tipping Restraint Hardware (AA) is properly installed, it can provide protection against unexpected tipping of the Unit due to small tremors, bumps or climbing.
• Each Tipping Restraint Hardware (AA) includes one Unit Anchor, one Wall Anchor, one Anchor Tether, and four Anchor Screws. Use these to complete the following steps for a proper installation.
• Locate a secure wall stud behind the unit closest to the left side.
• Align the Unit Anchor with a wall stud and attach to the Unit with two Anchor Screws using a Philips Screwdriver. The Anchor Screws must pass through the Top Assembly for proper installation.
• Align the Wall Anchor in the center of the wall stud, at level with the Unit Anchor, and attach with two Anchor Screws using a Philips Screwdriver.
• On the Anchor Tether, detach the cable from the connector and loop the loose cable through the eyelets on the Wall Anchor and Unit Anchor. Reattach the loose cable to the connector, but do not tighten.
• Locate a secure wall stud behind the unit closest to the right side and repeat the steps above.
• Tighten both Anchor Tethers by pulling the cable through the connector.

NOTE : Installation of the Tipping Restraint Hardware (AA) will provide a small space between the wall and the unit. This will allow you to run power cords and connector cables to your television or other devices placed on top of the unit.
WARNING : Installing the Tipping Restraint Hardware will help prevent accidents or damage to the unit.

Operation

NOTE : The control panel can be accessed at the upper-right corner of the insert.

1 Powering the fireplace

• Push the Power button to supply power to all functions of the fireplace and put the insert in standby mode.
• Push the Power button again to turn off all functions.

NOTE : All previous settings are held in memory, so the next time you power up the fireplace, the unit will turn on with the same settings.
NOTE : Holding the Power button on the control panel for 10 seconds will disable the heater function.

2 Adjusting the flame
There are 5 brightness levels that can be selected and OFF (00) setting. Settings F5 – F1 decrease in brightness.

3 Adjusting the heater

• The fireplace contains two infrared quartz heating elements.
• The thermostat setting range is continuously ON or 82°F -62°F (27°C – 17°C). Set the heater to (00) to use the flame effects without the heat. The thermostat is adjustable by 2°F or 1°C increment. 11 Press the heater button on the control panel to turn on/off (00) and adjust the heater setting.
• The “+ / – ” buttons on the remote will increase / decrease temperature setting.

NOTE : To change between °F and °C press and hold the Heater button on the control panel for 3 seconds.

4 Setting the timer
Pressing the Timer button will cycle through the timer settings; 30 minutes, 1 Hour, 2H, 3H, 4H, 5H, 6H, 7H, 8H, 9H and off (00).

5 Adjusting the flame speed
Pressing the Speed button on the remote to cycle through the flame speed setting.
Each flame color option has speed options available. Setting S1 is slowest ranging up to setting S5 which is the fastest.

6 Replacing the remote control battery
When the remote control stops operating or its range seems reduced, it is time to replace the batteries with new ones.

• On the back end of the remote, press and slide the battery door open and remove the old battery.
• Insert two AAA batteries, checking that the + and – sides of the battery match inside the battery compartment.
• Replace the battery compartment door.

NOTE : Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nicad, NiMH, etc) batteries. Do not ingest batteries.
NOTE : Please operate the remote control at a slow measured pace. Press the remote control buttons with an even motion and gentle pressure. Repeatedly pressing buttons in rapid succession may cause the transmitter to malfunction.
NOTE : Batteries should be removed if the product is to be left unused for a long time.

Disposing of used batteries

• The battery may contain hazardous substances that could endanger the environment and human health.

• This symbol marked on the battery and/or packaging indicates that the used battery should not be treated as municipal waste. Instead, it shall be left at the appropriate collection point for recycling.

• By correctly disposing of used batteries, you prevent potential negative consequences for the environment and human health. Recycling used materials also
  conserves natural resources.

• For more information about collecting and recycling used batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased this product.

 Power cord information

This heater is for use on 120 volts. The cord has a plug as shown in the figure.
Connect to properly grounded outlets only.
Do not use a two-prong adapter. Never use an extension cord or relocatable power tap (outlet/ power strip).

9 Patented Safer Plug® information

This product is equipped with a Safer Plug®, which is an advanced safety device that helps detect electrical fires caused from faulty outlets.
Overloading of outlets, adapters and surge protectors may cause overheating, damage, and increased risk of fires. The Safer Plug continuously monitors the temperature in the plug and outlet and will turn off the heater to prevent unsafe outlet overheating.
If the Safer Plug cuts the power due to unsafe conditions it will show an “ Er ” message on the screen. If this occurs the Safer Plug has prevented a potentially unsafe condition.
To reset the device if this occurs, first allow the plug to cool down. Once the plug has cooled down, unplug the device and wait 5 seconds, then plug back in and continue to use normally.
If the Safer Plug continues to activate, your outlet may be faulty. Check your heater cord and plug connections. Faulty wall outlet connections or loose plugs can cause the outlet or plug to overheat. Be sure the plug fits tightly in the outlet. Heaters draw more current than small appliances. Overheating of the outlet may occur even if it has not occurred with the use of other appliances. During use check frequently to determine if your plug outlet or faceplate is HOT! If so, discontinue use of the heater and have a qualified electrician check and/or replace the faulty outlet(s).

FCC/IC Information

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.

Care and Cleaning

Dust your fireplace regularly with a soft non-lint-producing cloth or household dusting product.
Clean your fireplace with a gentle non-abrasive household cleaner. Dry your fireplace immediately with a soft cloth or towel.
The motors used on the fan and the flame generator assembly are pre-lubricated for extended bearing life and require no further lubrication. However, we recommend periodic cleaning/vacuuming of the fan/heater.
Make sure the unit is turned OFF and unplugged whenever you are cleaning the heater or fireplace.

WARNING : Make sure the power is turned off before proceeding with repairs. Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes. If repairing or replacing any electrical component or wiring, the original wire routing, color coding and securing locations must be followed. During any service of this appliance, the power to the unit must be turned off. First turn the main power switch to the OFF position. Then remove the electrical plug from the wall outlet.
WARNING : Electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electrical shock and injury to persons.
WARNING : Do not use this fireplace if any part of it has been underwater. Immediately call a qualified service technician to inspect the fireplace and replace any part of the electrical system.
WARNING : Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury.

Troubleshooting

fireplace has reached set temperature. The temperature around the fireplace might be a few degrees higher than in another area in the room.| Set the fireplace to a higher temperature or always “on”.
The display shows “   :”| The thermostat sensor is broken or disconnected.| Unplug the fireplace, remove the back panel of the fireplace and check that the
thermostat is plugged into the main circuit board. If this does not solve the problem contact customer service for a replacement thermostat sensor.
The display shows “ “| The thermostat sensor is short-circuited.| Contact customer service for a replacement thermostat sensor.
The display shows “ .| Manual Reset overheats protection has been triggered.| Inspect the heater and check that the air inlets and outlets are not blocked as this may cause overheating. Unplug the heater for 30 minutes and allow it to cool down. Replug and operate. Monitor the heater for signs of overheating. If the problem persists, discontinue use of the heater and contact customer service.
The display shows “ “| Power cord overheating protection has been activated.| Check your heater cord and plug
connections. Faulty wall outlet connections or loose plugs can cause the outlet or plug to overheat. Be sure the plug fits tight in the outlet. Heaters draw more current than small appliances. Overheating of the outlet may occur even if it has not occurred with the use of other appliances. During use check frequently to determine if your plug outlet or
faceplate is HOT! If so. discontinue use of the heater and have a qualified electrician check and/or replace the faulty outlet(s).
The heater does not blow warm air.| The heater is in a cool-down cycle.| Normal operation will continue to run for less than one minute before shutting down. Times will vary based on temperatures. During this time cool air will blow.
There is no power and the logs do not glow.| There is no power to the unit.| Check that the unit is plugged into a
standard 120V outlet. Press the Power button several times and make sure power is set to the “ON” position.
The logs are not glowing, and there is no flame effect.| The flame effect turned off.| Press the Flame button several times.
PROBLEM| ROOT CAUSE| CORRECTIVE ACTION
---|---|---
Flame effect works but the heater
the function does not and the ember bed
flashes when the Heater button is
pressed.| The heater is disabled.| With the power on press and hold the Power
button on the control panel for 10 seconds.
Once re-enabled the ember bed lights will
flash multiple times.
The remote control is not working.| There are no batteries.| Change the remote batteries.
The signal is poor.| Operate remote transmitter at a slow measured pace. Press the remote control buttons with an
even motion and gentle pressure. Repeat-
edly pressing buttons in rapid succession
may cause the transmitter to malfunction.
The remote is too far from the heater.| Operate the remote at a distance of less than
20 ft from the front of the appliance; point the remote at the control panel.

Replacement Parts

For replacement parts, call our customer service department at 1-800-986-3460, Monday – Friday 8 A.M. – 7 P.M. EST, and Saturday 9 A.M. – 6 P.M. EST.

Questions, problems, missing parts? Before returning to the store,
call Home Decorators Collection Customer Service
Monday – Friday 8 A.M. – 7 P.M. EST, and Saturday 9 A.M. – 6 P.M. EST.
1-800-986-3460
HOMEDEPOT.COM/HOMEDECORATORS
Retain this manual for future use.

Documents / Resources

| HOME DECORATORS COLLECTION 1006152680 Pembroke Electric Fireplace [pdf] User Guide
1006152680, Pembroke Electric Fireplace, 1006152680 Pembroke Electric Fireplace
---|---

References

• Home Decorators Collection - Home Decor - The Home Depot

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>