Solis 791 5 In 1 Table Grill for 8 User Manual

5 in 1 TABLE GRILL for 8
Type 791
User Manual

IMPORTANT SAFETY PRECAUTIONS

Please read through this user manual thoroughly before using your Solis Table Grill, so that you become familiar with your appliance and can use it safely. We thoroughly recommend that you keep these instructions and, if you pass the appliance on, that you also hand these instructions to the new owner.
For your own safety, please observe the following safety measures when using electrical appliances:

1. To prevent electric shock, neither the appliance nor the power cord and the power plug resp. connection adapter must come into contact with water or other liquids. Danger of electric shock! Water can enter the housing and damage the appliance! Should the appliance while connected to the power resp. the power cord or the power plug / connection adapter come into contact with liquid, use dry rubber gloves to immediately pull the power plug out of the socket. Do not start using it again before having it checked for functionality and safety by Solis or a service centre authorized by Solis.
2. Do not operate the appliance resp. pull or connect the plug with wet or moist hands or feet.
3. Before using the appliance, check that the voltage stated on the type plate of your appliance matches your mains voltage. We do not recommend operating the appliance with a multiway plug adapter.
4. Do not make any adjustments to the appliance, cable, plug or accessories.
5. Do not leave the power cable hanging over table edges to prevent the appliance from being pulled down. Make sure that neither the appliance nor the power cord or plug comes into contact with hot surfaces, such as hotplates or a radiator, or that they come into contact with the appliance itself.
6. Never carry the appliance by the power cord and do not place anything on the power cord. Never pull on the power cord to disconnect the appliance from the power mains. Only pull on the plug.
7. Install the power cord so that nobody can trip over it. Keep clear of pointed objects.
8. Always fully unwind the power cord before connecting the power plug to the power socket.
9. Keep the appliance away from hot gas, hot ovens and other heat-emitting appliances or heat sources. Never use the appliance on a hot or wet surface. Never place the appliance near moisture, heat and naked flames. Keep the appliance away from moving parts or appliances.
10. We recommend that you do not use an extension cable with this appliance. Do not place the appliance directly underneath a power socket.
11. During use, the appliance must be placed on a dry, stable and heat resistant surface. Place the appliance in the middle of the table, not near the corners of the table. Furthermore, the surface should be resistant to drops that might originate from the appliance.
12. The appliance is not designed for outdoor use. The appliance must not come into contact with water or spray water. Do not use in vehicles or on boats.
13. Keep a minimum distance of 50 cm between the appliance and walls, curtains or other heat and steam sensitive materials and objects. Please note that air must be allowed to circulate freely around the appliance.
14. Never cover the appliance with cloths or the like while it is in use or in a still warm state.
15. Unplug the appliance when it is not in use or unattended or if it needs to be disassembled, reassembled or cleaned. We recommend the use of a residual current device (RCD safety switch) to ensure additional protection during the use of elec-trical appliances. It is advisable to use a safety switch with a rated residual operating current of 30 mA maximum. For professional advice consult an electrician.
16. Improper use creates the risk of injury! No liability is assumed in the case of potential damages or injuries.
17. Never reach for an appliance that has fallen into water or other liquids. Always use dry rubber gloves to pull the plug before taking it out. Do not start using it again before having it checked for functionality and safety by Solis or a service centre authorized by Solis.
18. Never place the appliance in such a way that it might fall into water or come into contact with water or another liquid (e.g. in or next to a sink).
19. Never submerge the appliance, power cable or plug / connection adapter in water, or bring it into contact with water or other liquids.
20. Place the appliance so that it is never exposed to direct sunlight.
21. Never put sharp or pointed objects and tools into the appliance openings. The appliance may become damaged – danger of electric shock!
22. Never use kitchen utensils or barbecue tools on the grill plate and the trays resp. on the accessories (raclette pans, round mini-woks). Never use a knife to cut on the grill plate or in the pans. The non-stick coating might be damaged.
23. Do not shake or move the appliance while it is in use. Never relocate the switched-on appliance! The surfaces of the Table Grill get very hot and might cause burns.
24. Only use the appliance as described in this manual. Only use with the provided accessories or accessories recommended by Solis, incorrect accessories or misuse can lead to damage of the appliance, fire, electric shock or personal damage.
25. Never start the appliance using a remote control or timer switch.
26. This appliance is only suited for household use and not for commercial use.
27. Remove and discard all packaging materials and potential stickers or labels (except for the type plate) before using the appliance for the first time.
28. Check the appliance before each use and ensure that the appliance, power cord and plug resp. connection adapter are not damaged and no parts have come loose.
29. To prevent electric shock, do not use the appliance if cord or power plug are damaged or if the appliance has other faults, has fallen down resp. is damaged in any other way or if parts have come loose. Never attempt repairs yourself but take the appliance to Solis or a service centre authorized by Solis in order to get it inspected, repaired or mechanically and electrically maintained, in order to avoid a hazard.
30. People with limited physical, sensorial or mental capabilities as well as unknowing or inexperienced people and children must not use the Table Grill except when supervised or thoroughly instructed on how to use the appliance by a person responsible for their safety. Additionally, they must be aware of the dangers arising from the appliance and know how to operate it safely. Cleaning and maintenance of the appliance must not be done by unsupervised children. Under no circumstances must the appliance be used or cleaned by children under the age of 8. The appliance and its power cord have to kept away from children under the age of 8.
31. Keep the appliance and the power cord away from children and pets during and even after use, while it is still warm – risk of burns!
32. Children must be supervised to prevent them from playing with the Table Grill.
33. CAUTION: The temperatures of the appliance parts, grill plate and die-cast plate are very high during and some time after use! Do not touch the hot appliance parts. Always let the appliance cool down completely first – risk of burns!
34. Always switch the appliance off with the red main switch, disconnect the power plug and the connection adapter from the appliance when not using the appliance or before cleaning it. Let the appliance cool down completely before disassembling, cleaning or moving the appliance.
35. Only plug the power plug into the power socket resp. only switch the appliance on if the appliance is placed on a dry, stable and heat resistant surface.
36. Never place empty or used pans or spatulas on the hot grill plate or cooking surfaces – the food leftovers burn! Always use the cold zone as a depositing area, meaning the heat resistant stainless steel plate.
37. NOTE: When using the appliance for the first time, a little bit of smoke might develop. This is normal for appliances that heat up during use and will stop after a short period of time.
38. Pull the plug after every use. Only then, the appliance is fully switched off.
39. Should you notice a strange smell or sound, pull the plug. Do not start using the appliance again before having its functionality and safety checked by Solis or a service centre authorised by Solis.
40. Keep the appliance clean. Always switch the appliance off and pull the plug from the power socket and the connection adapter from the appliance socket before cleaning and storing the appliance. Please refer to the notes given in the section “Cleaning and care“ on page 65 of this manual.
41. Always fully unwind the power cord before connecting the connection adapter to the appliance socket and the power plug to the power socket.

APPLIANCE DESCRIPTION

A Grill plate with two usable sides
B Upper heating element (heating coil)
C Die-cast plate
D Lower heating element
E Stainless steel feet with plastic knobs
F Stainless steel plate (cold zone)
G Red main switch, activates the upper heating element
H Temperature control for the upper heating element
I Lower heating element button
J Appliance jack for connection adapter of power cord
K Accessories:
8 square pans with non-stick coating for raclette or pizza
8 round mini-woks with non-stick coating for warming up and gratinating small portions
8 plastic spatulas to easily take the content out of the pans 1 dough cutter for pizzas
Power cord with power plug and connection adapter (country-specific)

A Grill plate with two usable sides:

• Classic grill plate with grooved and smooth zone; the grooved area is suitable for grilling meat, the smooth area for grilling fish, seafood, vegetables etc.
• Grill plate with round insets for preparing crêpes, or as a heater plate for the 8 round mini-woks.

The grill plate is made from die-cast aluminium, is extremely heat resistant and also equipped with a special non-stick coating.

B Upper heating element (heating coil)
The heating coil is positioned directly beneath the grill plate, it heats the grill plate and supplies the foods in the pans on the die-cast plate directly beneath it with top heat.
The temperature of the heating coil is smoothly adjustable thanks to the temperature control.
C Die-cast plate
The raclette pans and round mini-woks are placed on the die-cast plate during grilling to gratinate and heat their contents.

D Lower heating element
Another heating element is placed underneath the die-cast plate. It can be switched on in addition to the upper heating coil with an extra button.
Like that, the foods on the die-cast plate can be heated from below as well. This is ideal e.g. for small pizzas, gratins or for warming up foods.
CAUTION: The lower heating element can not be switched on individually, only in addition to the upper heating coil. The temperature of the lower heating element can not be adjusted.
E Stainless steel feet with plastic knobs
Thanks to the plastic knobs there will not be any scratches on the plate below.
F Stainless steel plate (cold zone)
The stainless steel plate, the so-called cold zone, serves as a tray for unused pans and spatulas during grilling.
It is separated from the grill itself and thus can be easily removed and cleaned.
There are additional plastic knobs on the corners of the tray to prevent it from scratching the table.
G Red main switch, activates the upper heating element
The red main switch is for switching the appliance on and off. Once the red main switch is set to „I“ and the red light is glowing, the heating coil begins to heat up.
The desired temperature can be set with the temperature control.
H Temperature control
You can smoothly adjust the temperature of the upper heating element with the temperature control. The bigger the dots around the temperature control, the hotter the upper heating element gets.
Once the appliance has been switched on with the red main switch, a red or green light glows around the temperature control.
Turn the temperature control to the right (clock wisely) to the desired position. The light surrounding of the temperature control glows red as long as the appliance heats up.
Once the set temperature is reached, the light surrounding of the temperature control switches to green.
This will happen within the first approx. 75% of the heating power range. Within the remaining approx. 25% to the maximum heating power, the light surrounding always lights up red.
Red light = Heating-up phase
Green light = Temperature has been reached
CAUTION: The power cord has to be removed from the appliance resp. the power plug has to be pulled if you do not use the appliance.
I Lower heating element switch with control light
You can additionally activate the lower heating element with the black switch.
Once you have set the switch to „I“, the adjacent control light lights up. Then, also the heating element underneath the die-cast plate heats up, heating the pans from below as well. The temperature for the lower heating element can not be adjusted.
CAUTION: The lower heating element can only be activated in addition to the upper heating element, it can not be activated individually.
J Appliance jack for connection adapter of power cord
The connection adapter on the power cord has to be connected to this appliance jack before the power cord is plugged into the power socket to connect the appliance to the power grid.

BEFORE FIRST USE

• To burn production residues on the grill plate and to burn in the protective coa-ting on the heating element, all removable appliance parts have to be cleaned and the assembled appliance has to heated up before first use.

1. Remove the grill plate from the appliance base. Clean the grill plate, the dough cutter, the square pans and the round mini-woks as well as the plastic spatulas
   in hot dish water with a soft towel or sponge. After that, rinse all parts in clear water and dry them.

2. Wipe the die-cast plate and the cold zone tray clean with a moist, soft towel.

3. Place the appliance on a dry, heat and moisture resistant worktop.

4. Place the dry grill plate back on the base and plug the connection adapter of the power cord into the appliance jack and the power plug into a suitable power outlet. The pans should not be in the appliance.

5. Switch the appliance on with the red main switch (red function light glowing) and set the temperature control to the highest position (all the way to the right). Additionally, switch on the lower heating element by setting the black switch to „I“.

6. Let the appliance heat up for 10 minutes, after that return the temperature control to its lowest setting (all the way to the left) and set both switches back to „0“ to switch the appliance off. Pull the plug and let the appliance cool down.

7. Wipe both sides of the cooled down grill plate with a slightly moist towel.

8. Your appliance is now ready for use.

STARTING UP

• USING THE APPLIANCE ONLY WITH THE UPPER HEATING ELEMENT (HEATING COIL) AS A GRILL OR RACLETTE SET

1. Place the clean appliance on a dry, stable and heat and moisture resistant table.
2. Choose which side of the grill plate suits you best and place it on the appliance base. Rub the grill plate with a paper towel soaked in cooking oil.
3. Plug the connection adapter of the power cord into the appliance jack and the power plug into a suitable power outlet.
4. Switch the red main switch to „I“, the red function light glows.
5. Set the temperature control to the maximum power and let the appliance heat up for approx. 15 minutes. In this setting, the light surrounding lights up red.
6. In case you want less than maximum power, turn the temperature control to the desired position.
   You can now freely place your grillables on the grill plate. The grooved area is especially suitable for meat, the smooth area is especially suitable for fish, seafood or vegetables.

The raclette cheese and the mini pizza can be put in the square pans and placed on the die-cast plate. This way, everything will be deliciously baked.
Please use the included plastic spatulas to take the foods out of the pans.
Please use a heat resistant plastic kitchen spatula to remove the grillables from the grill plate. Never use metal kitchen tools, these might damage the non-stick coating. For the same reason, do not cut directly on the grill plate or in the pans and never use barbecue tools. Avoid prolonged contact of the plastic tools with the hot grill plate / the hot pans.

USING THE APPLIANCE WITH THE LOWER HEATING ELEMENT SWITCHED ON ADDITIONALLY

If you wish to use the bottom heat under the die-cast plate as well, you can addi-tionally switch on the lower heating element. To do that, set the black switch to „I“, the adjacent function light lights up and the lower heating element heats up. The function light next to the switch lights up as long as the lower heating element is switched on.
The temperature of the lower heating element can not be adjusted.

CAUTION: The lower heating element can only be used in addition to the upper heating element, not individually. When you switch the upper heating element off with the red main switch, the lower heating element is switched off as well.
Thanks to the lower heating element, you can heat the foods in the pans on the die-cast plate from below. Like that, you can e.g. bake small pizzas or make potato gratins resp. warm foods in the pans.

■ TIPS FOR PERFECT GRILLING:

• Both the square raclette pans and the round mini-woks can be placed on the die-cast plate.
• Always park the pans and plastic spatulas on the lower stainless steel plate, the so-called cold zone, when taking a break from eating. If you leave the food-filled pans on or in the hot appliance, the foods will burn in and the coating might be damaged.
• Never turn the grill plate around while the appliance is hot. The grill plate is very hot, you might burn yourself.
• Do not use any metal kitchen utensils or knives on the grill plate or in the pans, they might damage the non-stick coating.
• Marinate or spice the meat before grilling but salt it only after you have taken it from the grilling surface, otherwise the meat will lose too much of its juice.
• Bratwursts should be broached before grilling to prevent them from cracking.
• Ideally, take the grillables out of the fridge 30 minutes before grilling them. They will grill faster and you prevent thicker pieces of meat from staying cold inside.

• GRILLING SURFACE WITH ROUND INSETS

You can also use the side of the grilling surface with the round insets.
It is especially suited to preparing foods in the round mini-woks or making crêpes directly on the grilling surface.

• SWITCHING THE APPLIANCE OFF
  If you have additionally switched on the lower heating element, first set the black switch to „0“. The function light next to the switch goes out.
  Now, turn the temperature control to the lowest temperature (turn the knob all the way to the left) and also set the red main switch to „0“. The red function light in the switch goes out, as does the light surrounding of the temperature control.
  Pull the plug and let the appliance cool down completely before cleaning it. We recommend carefully cleaning the grill plate, the accessories and also the appliance base after every use.

CLEANING AND CARE

Check if the power cord has been removed from the appliance and if the grill plate and die-cast plate have cooled down completely.
If the grill plate and the pans are heavily dirty, you can soak them in lukewarm water for some time or remove the dirt with a bit of oil and a paper towel. Under no circumstances use abrasive cleaners or solvents or steel scourers.
Clean the grill plate, the pans, the dough cutter and the plastic spatulas in hot water with a mild detergent and a soft sponge or towel. After that, rinse and dry everything carefully. The parts are not dishwasher safe.
The stainless steel plate can be cleaned with a moist towel and then dried.
Clean the appliance base with the die-cast plate for the pans as well as the power cord – in case should it be dirty – with a slightly moist towel. Never submerge the appliance base, the power cord and the power plug resp. connection adapter in water or other liquids and do not spray water or other liquids onto the appliance parts. Risk of electric shock!
Do not use aggressive cleaners or solvents as well as abrasive materials for any of the appliance parts. They might damage the surface.
Afterwards, reassemble the appliance.

STORAGE

When you do not need the table grill, it has to be disconnected from the power grid and cleaned and dried.
The power cord should be removed and stored next to the completely cooled down appliance.
Best store the completely cooled, cleaned and dry appliance fully assembled in the original packaging, including the accessories. Do not place any objects on the appliance.

TECHNICAL SPECIFICATIONS

Technical changes reserved.

DISPOSAL

EU 2011/65/EU

Information for correct disposal of the product in accordance with the European Directive EU 2011/65/EU.
At the end of its working life this equipment must not be disposed of as an household waste. It must be taken to special local community waste collection centres or to a dealer providing this service. Disposing of electrical and electronic equipment separately avoids possible negative effects on the environment and human health deriving from an inappropriate disposal and enables its components to be recovered and recycled to obtain significant savings in energy and resources. In order to underline the duty to dispose of this equipment separately, the product is marked with a crossed-out dustbin.
Solis of Switzerland Ltd reserves the right to carry out technical and visual changes and modifications to improve the product at any time.
SOLIS HELPLINE
This item stands out due to its long-life cycle and reliability. Despite this though, if a malfunction ever occurs, simply give us a call. Often a breakdown can be easily and quickly remedied with the right tip or technique without having to straight away send off the device for repair. We will give you all the advice and practical support you require. The contact addresses can be found at the end of this manual.
Keep the original packaging in a safe place so that you may use it in the event that transportation or shipping of the product becomes necessary.

• Solis customer service

Please contact us in advance of sending in products for return or repair. We will gladly give you the respective address. Alternatively, you can simply visit www.solis.com.

International
** Solis Produzione SA
Centro Solis
Via Penate 4
CH-6850 Mendrisio
Switzerland
Address for return shipment of goods differs – please refer to
[ www.solis.com](http://www.solis.com)
** +41-91-802 90 10
@support.ch@solis.com
www.solis.com

References

• Solis of Switzerland - Europe - Swiss quality household appliances
• Solis of Switzerland | België
• Solis of Switzerland - Schweiz - Swiss quality household appliances
• Solis of Switzerland - International - Swiss quality household appliances
• Solis of Switzerland | Deutschland

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>