MiBOXER LS4 0/1-10V Dimming Driver User Manual
- June 9, 2024
- MiBOXER
Table of Contents
- MiBOXER LS4 0/1-10V Dimming Driver
- Product Information
- Product Usage Instructions
- Features
- Connection diagram
- Linking Code / Unlinking Code Instructions
- Signal transmitting
- The mode of “Do Not Disturb”
- Scan the QR code to watch the video instruction
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
MiBOXER LS4 0/1-10V Dimming Driver
Product Information
The Subordinate New Brand 0/1~10V Dimming Driver, Model No.: LS4 is a dimming driver that can be used to control LED lights with apush button. It has a DC input of 12V~24V and can be connected to an AC power supply. The driver is compatible with 10V PWM dimmer, 0~10V dimmer, and 1~10V dimmer. It can be linked or unlinked using the power and light buttons on the driver. The driver can transmit signals to another light within 30m and can be controlled using a remote control or smartphone app.
Product Usage Instructions
-
To turn on or off the light, short press the push button.
-
To dim the light, long press the push button.
-
To link the driver to another light, follow the below steps:
-
Switch off the light, wait for 10 seconds, and switch it on again.
-
Short press the link/unlink button three times within three seconds when the light is on.
-
The light will blink three times slowly, indicating successful linking.
-
If the light does not blink slowly, repeat the above steps. Note that lights that have already been linked cannot be linked again.
-
To unlink the driver from another light, follow the below steps:
-
Switch off the light, wait for 10 seconds, and switch it on again.
-
Short press the link/unlink button five times within three seconds when the light is on.
-
The light will blink ten times quickly, indicating successful unlinking.
-
If the light does not blink quickly, repeat the above steps. Note that lights that have not been linked do not need to be unlinked.
-
To activate or turn off the Do Not Disturb mode, follow the
below steps: -
Press the OFF button three times within three seconds and press the ON button three times to activate the mode. The LED light will flash four times quickly.
-
To turn off the mode, press the ON button three times within three seconds and press the OFF button three times. The LED light will flash four times slowly.
-
Ensure that the voltage of the power supply is in accordance with the driver and check the connection of both the cathode and anode to avoid damage to the driver. Do not connect wires with power on. Non-professional users should not dismantle the lighting fixtures directly. Do not use the driver in places with a widely ranged metal area or strong electromagnetic wave nearby as it can seriously affect the remote distance.
Features
Adjust the brightness(0~100%) through 0~10V, 1~10V, 10V PWM and Push Dimming Signal. Also controlled by a smartphone, and with 4G controlling (2.4GHz gateway is needed). Adopt worldwide used 2.4GHz wireless technology, with low power consumption, long transmitting distance, and strong anti-interference, etc features; also with one-to-many control, and signal auto-transmitting function. The controller is with the over-and-under type terminal connection method to be easy to compatible with many kinds of lightings, and widely used on the control for hotel lighting, and home lighting, etc.
Connection diagram
Linking Code / Unlinking Code Instructions
Linking Code Instructions
- Switch off light, after 10 seconds then switch on again.
- Short press” | ” button 3 times within 3 seconds when light on.
- Lights blink 3 times slowly means linking is done successfully.
Linking failed if light is not blinking slowly, Please follow above steps again.
(Note: Light that have linked can’t link again)
Unlinking Code Instructions
- Switch off light, after 10 seconds then switch on again.
- Short press ” I ” button 5 times within 3 seconds when light on.
- Lights blink 10 times quickly means unlinking is done successfully.
Unlinking failed if light is not blinking quickly, Please follow above steps again.
(Note: Light haven’t linked that don’t need to unlink)
Signal transmitting
One light can transmit the signals from the remote control to another light within 30m, as long as there is a light within 30m, the remote control distance can be limitless.
Compatible with these remote controls (Purchased separately)
The mode of “Do Not Disturb”
It can be activated or turned off via remote control
Turn on “Do not disturb” (wide using in the area which have power failure
frequently to save energy)
Press “OFF” button three times within three seconds and press “ON” button
three times, Activated successfully once led light flashes four times quickly.
Attention: Do not disturb mode is activated
- When the light is OFF status (For example: Use app or remote to turn off light) The light is OFF status once you turn off power and turn on again. (User must turn off and turn on power twice times to activate light or use APP remote to activate light)
- When the light is ON status The light is ON status once you turn off and turn on power one time.
Turn off “Do not disturb”
Press the “ON” button three times within three seconds and press the “OFF”
button three times, closed successfully once led light flashes four times
slowly.
Attention: The light will be always in “ON” status if you turn on and
turn off the power once the user closed the “Do not Disturb” mode.
Scan the QR code to watch the video instruction
Attention
- Please check whether the voltage of the power supply is in accordance with the light, and please check the connection of both the cathode and anode, otherwise the light will be broken.
- Please don’t connect wires with power on. Please turn on again only when it is in right connection and no short circuit.
- Non-professional user cannot dismantle the lighting fixtures directly.
- Please do not use the light in a place with widely range metal area or strong electromagnetic wave nearby, otherwise, the remote distance will be seriously affected.