ETON UG VAG25 Plug and Play V.A.G. Tweeters Instruction Manual
- June 9, 2024
- ETON
Table of Contents
ETON UG VAG25 Plug and Play V.A.G. Tweeters
Product Information:
The Plug & Play V.A.G. Tweeters (UG VAG25) are specially designed for various V.A.G. models from the year of manufacture 2008 with MQB standard. The tweeters come with a strong neodymium magnet and dual damping materials, providing outstanding performance. The product includes a specially developed Plug & Play connector flange with 3-point mounting and accurately fitting V.A.G. specific dual connector plugs, making the installation process very easy. The cable crossover is specially tuned with high-quality components and has a 12 dB/Oct. slope as well as level adjustment (0 dB / +3 dB). The tweeters have a low resonance frequency of 1.2 kHz, a vented voice coil, and 4 ohms impedance.
Product Usage Instructions:
- Read all the safety instructions before installing the tweeters.
- Make sure you have all the necessary tools mentioned in the manual.
- Remove the door panel of your vehicle and locate the factory speaker location.
- Disconnect the factory speaker wires and remove the factory speakers.
- Connect the tweeter wires to the factory speaker wires using the accurately fitting V.A.G.-specific dual connector plugs.
- Mount the tweeters using the specially developed Plug & Play connector flange with 3-point mounting.
- Adjust the level of the tweeters according to your preference using the level adjustment (0 dB / +3 dB).
- Put back the door panel and test the tweeters for proper functioning.
Introduction
ETON thanks you for purchasing this product.
ETON loudspeakers and amplifiers guarantee outstanding performance. The
electrical, mechanical, and tonal properties are maintained throughout the
product’s service life. We wish you an enjoyable listening experience!
These instructions are designed to help you install your speaker correctly. Please read the instructions carefully before you start installation and connection. Audio sources such as your OEM radio may get distorted at high volumes.
Please note that loud and heavily distorted signals may destroy your loudspeaker
Safety Instructions
Attention!
Please read all the warnings in this manual. The information is in bold and
serves to inform you of the potential danger of personal injury or damage to
property.
Damage to hearing
SUSTAINED EXPOSURE TO VOLUMES OVER 85dB MAY DAMAGE YOUR HEARING. AMPLIFIER-
OPERATED CAR HI-FI SYSTEMS MAY PRODUCE SOUND PRESSURE LEVELS WELL OVER 130dB
AND PERMANENTLY IMPAIR YOUR HEARING. PLEASE USE COMMON SENSE AND AVOID SUCH
RISKS!
Volume and driver awareness
The use of music systems may prevent the driver from hearing important traffic
sounds and thereby constitute a driving hazard.
ETON accepts no liability for hearing loss, physical injury or damage to property resulting from the use or misuse of its products.
Tools
You will need the following tools, which you should have at hand.
- Several Torx screwdrivers in different sizes
- Flat-head screwdriver – size approx. 2 mm or plastic handle
- Plastic lever set
- Side cutter + cutter knife
- Suitable 2-component adhesive for securing
Tweeter installation
Remove the A-column cladding by carefully lifting it off with a suitable tool
and pull the tweeter cable out of the plug connector fixed to the A
-column.
Remove the three fusion points of the tweeter with a sharp knife. Place the tweeter onto the pins of the speaker opening. Make sure that all the clips are properly fixed into place and the adhesive ring creates a perfect seal.
To make sure, stick each of the three clips with a customary two-component
adhesive. Connect the plugs, to do this, use one of the two matching connector
plugs. (A or B, depending on the V.A.G. model).
For some V.A.G. models it makes sense to increase the level by +3 dB, for this replace the connectors (C). Check all cable plug connections and clips. Reassemble the A-pillars in reverse order. If clips are broken off during disassembly, replace them beforehand.
Technical Data
- 25 mm (1“) coated plug & play. fabric tweeter for various V.A.G. models
- Strong neodymium magnet with coupling volume and dual damping materials
- Specially developed Plug & Play connector flange with 3-point mounting
- Accurately fitting V.A.G. specific dual connector plugs
- Specially tuned cable crossover with high quality components and 12 dB/Oct. slope aswell as level adjustment (0 dB / +3 dB)
- Low resonance frequency 1.2 kHz
- Vented voice coil
- 4 ohms impedance
- Suitable for various V.A.G. models from year of manufacture 2008 with MQB standard
- Please note online compatibility list!
- Manufacture and development Made in Germany
ETON reserves the rigth to make modifications or improvements to the products illustrated without notice thereof. All rights belong to the respective owners. Total or partial reproduction of this User‘s Guide is prohibited.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>