ETON USB 6 AR Active Subwoofer Instruction Manual

June 4, 2024
ETON

ETON USB 6 AR Active Subwoofer Instruction Manual
ETON USB 6 AR Active Subwoofer

Introduction

ETON expressly thanks you for deciding to purchase this subwoofer and congratulates you on the selection of this excellent product

The ETON subwoofer is a guarantee for outstanding performance. The electrical, mechanical and tonal characteristics will be maintained at the original high standard throughout the entire operational life of this product. We wish you many pleasant listening hours.

Operating Instructions
The current operational instructions are designed to ensure correct installation of the amplifier. They contain information and essential procedures for the correct operation of the product and its attached external devices.
Please carefully study the operating instructions before beginning with the installation or the connection of the subwoofer.

Contents

  • USB 6 AR avtive undersea sub woofer
  • Cable remote control
  • Mounting and connection accessories incl. fuse-Holder with 10 A fuse
  • Manual

Safety Instructions

Attention !
Please read all warnings found in this manual.
This information is highlighted and included to inform you of the potential danger of personal injury or damage to property.

Hearing Damage
CONTINOUS EXPOSURE TO SOUND PRESSURE LEVELS OVER 85dB MAY CAUSE PERMANENT HEARING LOSS. HIGH POWERED AUTO-SOUND SYSTEMS MAY PRODUCE SOUND PRESSURE LEVELS WELL OVER 130 dB. THIS MAY CAUSE DAMAGE OF HEARING. USE COMMON SENSE AND AVOID SUCH RISKS!

Volume and Driver Awareness
Use of sound components can impair your ability to hear necessary traffic sounds and may constitute a hazard while driving your automobile.

ETON accepts no liability for hearing loss, bodily injury or property damage as a result of use or misuse of this product.

ATTENTION!
If sheet metal must be cut or removed contact your authorized  car dealer for professional advice. By damage to supporting body structures the safety certificate may be withdrawn.

Table of contents

The subwoofer is packed into an especially constructed protecting carton. Do not damage the packing and store it for future use in the case of possible damage. Upon receipt of the subwoofer verify that: The packing is
not damaged, the contents are according to specifications, the product shows no obvious damage.In the case of missing or damaged parts please contact immediately your dealer providing the model name as well as the serial number that is shown on the bottom of the subwoofer.

Tools

We recommend to place the following tools ready for installation:

  • Fuse-holder and fuse wrench for battery post
  • Wire strippers
  • Wire cutters
  • Tongs
  • Additional tools which are probably needed to remove panels in your car
  • Power- and remote wires in adequate lengths, widths and colours, speaker wires in adequate lengths.

NOTE: We recommend to use power cable at least 12 AWG for (B+) and (GND) battery wiring. A corresponding power cable incl. fuse holder and 10 A plug-in fuse is enclosed.

Precautions – Read first

Caution! Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury. This is not possible in every modern vehicle. Please ask your carmaker or see your owners handbook regarding battery change.

Note: The installation and adjustment of the Subwoofer should only be entrusted to qualified personnel. Please carefully read the operation instructions and follow the given directions regarding connection and adjustment of
the subwoofer.

Warning! Before connecting external devices that do not belong to this amplifier unit, please refer to the corresponding directions contained in the operation instructions for this device.

Warning! Under no circumstances should you open the subwoofer or attempt any repairs. If required contact your dealer to obtain technical assistance. Unauthorized changes will result in the cancellation of warranty.

Caution! The subwoofer must not be subjected to high pressure. Be careful that no foreign object or fluid can enter the subwoofer.

Before Installation

This section focuses on some of the vehicle considerations for installing your new subwoofer. Pre-planning your system layout and best wiring routes will save installation time.

When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments.

Before beginning any installation, follow these simple rules:

  1. Be sure to carefully read and understand the instructions before attempting to install the unit.

  2. For easier assembly, we suggest you run all wires prior to mounting your unit in place.
    Caution! Avoid running power wires near the low level input cables, antenna, power leads, sensitive equipment or harnesses. The power wires carry substantial current and could induce noise into the audio system.

  3. Route all of the RCA cables close together and away from any high current wires.

  4. Use high quality connectors for a reliable installation and to minimize signal or power loss.

  5. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

  6. Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

  7. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

  8. ALWAYS protect the battery and electrical  system from damage with proper fusing. Install the appropriate fuse holder and fuse on the +12 V power wire within 18“ (45.7 cm) of the battery terminal.

  9. When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connections should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle. Seat belt bolts should never be used for connecting to ground.

Features

  • USB 6 AR active under-seat sub woofer, for for mounting inside the vehicle, for example under a seat, in the front foot well or other suitable places.

  • Music power rating: 160 W (80 W x 2) Max.

  • Rated power: 100 W (50 W x 2) RMS

  • Impedance: 2 ohms + 2 ohms
    Double voice coil

  • Crossover frequency: ~ 50 – 100 Hz

  • Max. current consumption: 10 A

  • Phase rotation: 0° / 180

  • RCA (Cinch) low-level input

  • Combination connector with integrated high level input (Hi-Level In), +12V / GND power connection, remote input

  • Operating voltage: 14,4 V (10V-16V) for vehicles with start-stop function

  • Dimensions: 290 x 202 x 77 mm (LxWxH)

  • Weight: 4.4 kg

Installation and wiring

CAUTION:

  1. Use either RCA line level OR speaker level  inputs. Do no connect both at the same time.
  2. Make sure that the switching voltage (blue/ white wire) is connected when using the cinch inputs!

With control via the Low-Level Inputs (also referred to as RCA Inputs), connect the blue/ white color remote wire from the USB 6 AR to the vehicle`s head unit so USB 6 AR will be turn on and off with systems.

With control via the High-Level Inputs, first the speaker harness will need to be spliced the wire side of the splitter. Then connect the white wire to the left [+],white/black wire to the left [-], grey to the right [+],and grey/black to the right [-] corresponding vehicle wires, and finally plug the supplied harness into the High-Level Inputs/power matching connector on the amplifier panel of the subwoofer.

Secure the subwoofer to the installation location of your vehicle with suitable fastening material or the supplied installation accessories, screw it tight!

**Suggestion of Subwoofer placement

**

**In compartment

**

**Under the seat

**

In trunk

ATTENTION:
Make sure that the subwoofer is properly screwed and secured. Loose and unsecured parts can become unpredictable projectiles in the interior of the vehicle in the event of an accident and cause serious injuries.

If there is distortion of a popping noise from the subwoofer input level is too high. If the subwoofer has prolonged use in this condition, this may result in deterioration of performance or may cause damage to the subwoofer!

Cable remote control

Cable remote control

You can adjust the level of your subwoofer by using the cable remote control.

Specifications

Model USB 6 AR
Chassis 6″ (150 mm) with double voice coil
Rated power RMS 100 W RMS (50 W x 2)
Maximum output power 160 W (80 W x 2)
Impedance 2 Ω + 2 Ω
Cross-Over frequency low-pass filter (LPF) 50 ~ 100 Hz
 Signal Noise Ratio 91 dB
Maximum current consumption 10 A
Sensitivity (Distortion level 1%) RCA input 82 mV – Speaker input 0.8 V
Phase-Shift 0° / 180°
Source voltage 14.4 V (10 V ~ 16 V)
Dimensions (LxWxH) 290 mm x 202 mm x 77 mm
Weight in kg 4,4 kg
Remotecontrol Ja / Kabel


ETON Car-Audio GmbH

Dinkelweg 6
89233 Neu-Ulm
Germany
www.eton-caraudio.com

CE-Certification

**Certificate of Conformity

**

The following product has been tested by us with the listed standards and found in conformity with the council EN 55032:2012. It is possible to use CE marking to demonstrate the conformity with this EMC Directive.

Manufacturer ETON Car-Audio GmbH
Address: Pfaffenweg 21, 89231 Neu-Ulm
Trade Mark ETON
M/N : RES 5 FLA
Art.-No.:
#70.007

Test Standards :

  • EN 55032: 2015 + A11: 2020
  • EN DIN EN 50498:2010
  • EN 61000-3-3: 2013 + A1: 2019
  • EN 55035: 2017 + A11: 2020
  • EN50498: 2010

RoHs Guidelines:

  • 2011/65/EU

Neu-Ulm, 17.11.2020
Signature
(Reiner Kröner, CEO)

ETON reserves the rigth to make modifications or improvements to the products illustrated without notice thereof. All rights belong to the respective owners.
Total or partial reproduction of this User‘s Guide is prohibited.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals