eTon Elite Satellit HD Radio User Guide
- June 5, 2024
- ETON
Table of Contents
- eTon Elite Satellit HD Radio
- MAJOR FEATURES OF THE ELITE SATELLIT HD
- DIAGRAMS
- GETTING STARTED
- BASIC RECEIVER OPERATION
- MEMORY FUNCTIONS
- HD RADIO OPERATION
- SEEK FUNCTION
- T-SCAN FUNCTION
- CLOCK & TIMER FUNCTIONS
- SETTING THE 24 HOUR CLOCKS MANUALLY
- MEM CH and select the memory channel to be associated with the timer.
- MISCELLANEOUS FUNCTIONS SNOOZE
- TROUBLESHOOTING
- SUGGESTED REFERENCES
- WARRANTY REGISTRATION
- LIMITED WARRANTY TO THE ORIGINAL CUSTOMER
- SERVICE INFORMATION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
eTon Elite Satellit HD Radio
MAJOR FEATURES OF THE ELITE SATELLIT HD
-
Frequency Coverage: 150-30,000 kHz, includes shortwave, medium wave AM broadcast band and longwave; 76 – 90 MHz or 87-108 MHz (selectable) FM broadcast band.
-
Reception Modes: AM, FM-stereo, Single Sidebar (selectable USB/LSB) and CW.
-
Digital Display: large 5.7-inch square, 240 x 320 pixel, dot matrix display. Shows all modes and selected functions. Programmable Memories: 500 user programmable with alpha labeling plus 1200 user definable country memories, for a total of 1700. Memory Scan Function.
-
Digital Phase Lock Loop (PLL) Synthesized Tuning with Direct Digital Synthesis (DDS) for drift-free frequency stability and finest tuning resolution.
-
Dual Conversion Superheterodyne Circuit: results in minimized interference through superior selectivity.
-
Excellent Sensitivity: yielding a true high-performance receiver. High Dynamic Range: allowing for detection of weak signals in the presence of strong signals.
-
Selectable Bandwidths: 1.0,1.8,2.0,2.5,3.0,4.0,6.0 kHz
for excellent selectivity. -
Single Sideband Synchronous AM Detector: selectable USB/LSB or double sideband to minimize adjacent frequency interference and fading distortion of AM signals.
-
IF Passband Tuning: an advanced tuning feature that functions in AM and SSB. Greatly helps reject interference.
-
Tuning Modes: variable-rate tuning knob, direct keypad frequency entry, up/down pushbuttons and auto-tuning.
-
Direct Shortwave Band Entry, allows instant access to the shortwave band of choice.
-
Selectable AGC: ON/OFF.
-
Display Backlighting: evenly lit tri-color backlight enables display viewing under all lighting conditions.
-
Dual Programmable Clocks with WWV or RDS Auto-Setting. Dual-Event Programmable ON/OFF Timers: can be used for recording or ‘alarm clock’ function, plus separate Snooze and Sleep timers.
-
Superior Audio Quality via a bridged type audio amplifier, providing high output power with battery operation. Separate, continuous bass and treble tone controls. Headphone Jack.
-
Stereo Line-Level Output: for recording or routing the output to another device such as a home stereo.
-
Calibrated LCD signal strength meter.
-
Built-In Antenna: Telescopic antenna for long wave, shortwave and AM and FM broadcast band reception.
-
External Antenna Connection for the addition of auxiliary antennas, e.g. professionally engineered shortwave antennas; long-wire shortwave antennas; specialized AM broadcast band antennas for enthusiasts of AM DX’ing; FM broadcast band antennas.
-
Power Sources: four internal “D” cell batteries (not included) or the included AC adaptor.
DIAGRAMS
-
External Level Equalizer
-
Treble
-
Bass
-
Volume
-
Battery Access Door
-
Direct Key Input
-
Function Soft Keys – LW/MW/SW
-
Store Key
-
Delete Key
-
Tag Key
-
T.Scan Key
-
Seek Key
-
Time
-
Squelch
-
DX Key
-
Fast/Tuning Lock
-
Tuning Knob
-
Mode Soft Keys
-
Power Key
-
LCD Display
-
Speaker
-
Telescopic Antenna
-
Line In Socket
-
Line Out Socket
-
HF Antenna Internal/External Switch
-
FM Antenna Internal/ Switch
-
External Antenna Socket
-
External 5 VDC Power Socket
-
External Speaker Socket
-
Headphone Socket
-
Snooze/Sleep key
-
Light key
-
Signal Strength
-
Squelch Level
-
Internal/External Antenna
-
DX (RF Preamplifier Active)
-
Seek Mode Indicator
-
Frequency Display
-
Meter Band Indicator
-
Stereo/Mono Indicator
-
Mhz/kHz Indicator
-
Menu Soft Key Label
-
AGC Mode Indicator
-
IF Bandwidth Indicator
-
Passband Tuning Status
-
Selects AM or AM Sync Modes
-
Selects Upper or Lower Sideband
-
Country Mode Select Soft Key
-
Indicates Tune Lock Engaged
-
Memory Mode Select Soft Key
-
Air Mode Select Soft Key
-
MW (AM Broadcast)/LW (Longwave) Select Soft Key
-
Selects Shortwave & Band Select Modes
-
Selects FM or FM HD Mode
-
Selects Aux input
-
Indicates Local (L) or Universal (U) Time
-
Battery Indicator
-
Indicates Various Errors
FIGURE 6: MEMORY & COUNTRY DISPLAYS -
Frequency of Selected Channel
-
Memory or Country Mode
-
Cursor Showing Selected Channel
-
“T” Indicating Marked T-Scan Channel
-
Channel Numbers
-
Softkey Labels & Parameters
-
Memory & Country Mode Indicators
-
Meter Band Identifier
-
LW, MW, SW, AIR OR FM & FM HD Band
-
Indicates kHz or Mhz
GETTING STARTED
WHAT THE ELITE SATTELIT INCLUDES
- AC adaptor
- Getting Started Guide
NOTE: In the instructions which follow, numbers in square brackets [ ] refer to the labels in the drawings in the “3 Diagrams” section.
EXTERNAL POWER SOURCES
Plug the AC adapter into the “DC IN 5V” socket on the right side of the Elite
Satellit [Figure 2, # 29] and connect the adapter to an AC Power source.
If batteries are installed and external power is lost, the receiver will
continue to operate on battery power even with the DC plug inserted. If this
occurs, the re-ceiver will alert the user with a POWER LOSS indication and
with a POWER LOSS beep if the POWER LOSS beep feature is enabled.
BATTERY POWER
If portable operation is desired, the unit may be pow- ered with four “D” cell
batteries. Alkaline batteries are preferred, but are not required. To install
the batteries, proceed as follows:
- Position the receiver with the front panel towards you.
- Open the battery access door located at the lower left corner of the front panel [Figure 1, # 5].
- Inside you will find an additional door.
- Remove this door by pressing down and pulling outward on the “OPEN” tab.
- Insert the first of four “D” sized batteries into the battery opening with the plus end of the battery to your left.
- Slide the battery to the right and continue in this manner until all four batteries are installed. Replace the inner door and close the outer door.
NOTE: Check the batteries periodically for leakage. IF UNIT IS TO BE STORED OR OTHERWISE NOT USED FOR AN EXTENDED PERIOD OF TIME, REMOVE THE BATTERIES TO PREVENT CORROSION AND POSSIBLE DAMAGE TO THE RECEIVER.
BATTERY CONDITION
Battery condition can be observed when the unit is turned on or if the ‘LIGHT’
button [Figure 3, # 32] is pressed if no external power source is connected to
the receiver. When the ‘POWER’ key [Figure 1, # 20] is pressed, or when the
‘LIGHT’ button is pressed, a screen will be observed similar the signal
strength bar [Figure 5, # 36] The further the bar extends toward the Left, the
more charge remains in the batteries.
If a flashing “LO BATT” is observed in the upper right hand corner of the LCD
display, the batteries are too low for satisfactory operation and should be
replaced.
ANTENNAS
The Elite Satellit is equipped with an internal telescopic antenna [figures 2,
3, & 4 # 23] which should provide excellent reception on the SW, AM, and FM
broadcast bands. A PAL type antenna connector, located on the left side panel,
[Figure 2, # 28] is provided for external antennas. An optional adapter will
adapt a female type F connection to the PAL-type connector on the Elite
Satellit.
On the left side of the Elite Satellit, you will find two antenna selection
switches [Figure 2, # 26 & 27]. The lower one is for FM, and upper one is for
LW, MW, & SW. Make sure these switches are set for EXTERNAL if you are using
an external antenna or INTERNAL if you are not. If you choose INTERNAL, be
sure to extend the telescopic antenna to its full length.
BASIC RECEIVER OPERATION
FIRST STEPS
Please refer to the front panel illustration on page 6, Figure 1 and set the
controls as described below. This assumes that you have already installed
batteries and/or have connected to external power, and that the desired
antenna has been connected and selected as described in “Getting Started”.
Again referring to Figure 1, set the ‘EQUIL’ control [# 15], and the ‘TREBLE’
[# 2] and the ‘BASS’ [# 3] controls to the center of their ranges.
Press ‘POWER’ [Figure 1, # 20] and adjust ‘VOLUME’ [Figure 1, # 4] to a
comfortable level.
Select the desired band by pressing the ‘FM’, ‘SW’,
‘MW/LW’soft keys until the desired band is displayed on the front panel
display.
The selected band will be indicated by reverse video on the display. For
example, see [Figure 5, #57].
MANUAL TUNING
The ‘TUNING’ knob is used to fine tune through the frequencies on a selected
band. The rate at which tun-ing occurs, and the number of digits displayed to
the right of the decimal point in the display are controlled by the ‘FAST /
TUNING LOCK’ key [Figure 1, #17].
For course manual tuning, pressing either end of the ‘< SELECT >’ key [Figure
1, # 8] will step up or down respectively in 5 kHz steps on the LW, and SW
bands, and in 100 kHz steps (.1 MHz) on the FM band. On the MW band, it will
step up or down in either 9 kHz or 10 kHz steps, depending upon the setting of
item 3 in the RADIO SETTINGS menu. To change this setting, do the following:
-
Press the ‘MENU’ key [Figure 5, # 46].
This brings up the RADIO SETTINGS menu on the LCD display. -
Press the ‘3’ key to toggle between 9 kHz and 10 kHz.
-
Press ‘9’ to exit this menu.
In the USA, AM broadcast stations are spaced at 10 kHz intervals, so the 10 kHz setting should be used. However in some other parts of the world, they are spaced at 9 kHz intervals, so if you are in one of these regions, use the 9 kHz setting.
DIRECT FREQUENCY ENTRY
Direct entry of a desired frequency is possible using the ‘Direct-Key-Input’
keys [Figure 1, # 6]. While entering a frequency, if an incorrect number is
entered, pressing the ‘CLEAR/LOCK’ key will clear the entry in progress and
return the receiver to its previous settings. The second depression of the
decimal (.) key acts as an
‘ENTER’ and causes immediate response to the entered frequency. If you do not
press the decimal (.) key a second time at the end, the receiver will
automatically enter the fre- quency after a slight delay.
The SW band (1.8 – 30.0 MHz) frequencies are displayed and entered in kHz or
MHz, depending upon the user’s selection from item 4 of the RADIO SETTINGS
menu. To make the menu selection, press the ‘MENU’ soft key twice. Then press
‘Direct-Key-In-put’ key ‘4’. Repeatedly pressing the ‘4’ key toggles between
kHz and MHz as the display and entry method for the SW band. Leave the reverse
video entry on the desired display method. For example, line 4 on the menu
should appear as follows for entry in kHz:
“ 4 SW BAND ENTRY kHz / MHz“.
After making this selection, press ‘Direct-Key-Input’ key ‘9’ to exit the
menu. Note that if kHz is selected from the menu, the display will show
frequencies from 1.8 – 30.0 MHz in Kilohertz, and entries should be made in
kHz.
SHORTWAVE ‘METER’ BAND DESIGNATOR ENTRY
To facilitate tuning to particular sections of the short- wave band, the Elite
Satellit receiver permits entry of the ‘METER’ band designator. By
entering this
‘METER’ band number, the receiver automatically tunes to the low
frequency end of the correspond-ing ‘METER’ band. The search for the new
station location is thus limited to a particular smaller section of the entire
shortwave band spectrum.
Press the ‘SW BAND’ soft key [See Figure 5, # 57] to enter the shortwave
band tuning mode. The SW portion of the display indicator will now be in
reverse video. Now press the ‘SW BAND’ soft key a second time. The display
indicator will now appear as “SW BAND” , and the ‘METER’ number entry
prompt on the display will be flashing. At this point, you have approximately
3 seconds to do one of the following:
You can scroll through the available meter bands using the ‘TUNING’ knob or the ‘< SELECT >’ key, stopping on the desired ‘METER’ band. If you stop on a “METER” band for more than 3 seconds, the receiver will tune to that band, the “SW BAND” in-dicator will appear as “SW BAND “, and the short- wave band “METER” prompt will quit flashing.
LISTENING TO SHORWAVE STATIONS AND CHOOSING THE BEST SHORTWAVE BAND
Absolutely no technical knowledge or prior experience is necessary to fully
enjoy listening to shortwave sta-tions from around the world. It’s helpful to
understand the meaning of the term ‘bands’. For a more detailed intro- duction
to shortwave listening refer to the section titled UNDERSTANDING SHORTWAVE
BANDS in the USE AND CARE GUIDE’S APPENDIX.
Here are the most important bands with band name and frequency range: 13m,
21450-21850 KHz; 16m, 17480-17900 KHz; 19m, 15100-15800 KHz; 22m, 13570-13870
KHz; 25m, 11600-12200 KHz; 31m, 9200-10000 KHz; 41m, 7100-7600 KHz; 49m, 5800-
6200 KHz; 60m, 4750-5060 KHz.
Following are the best bands for the various times of day. This information
can be used worldwide. Note that some bands overlap several periods of the day
and that it always pays to experiment.
SUNRISE AND EARLY MORNING:
25, 31, 41, and 49 meters are usually good.
MID DAY:
13, 16, 19, 22 and, in some areas, 25 meters. Some-times these bands open up
early, so test them in the morning too.
LATE AFTERNOON AND AROUND SUNSET: 19, 22, 25, 31, 41 and 49 meters.
NIGHT:
60, 49, 41, 31, 25 meters, with 49, 31 and 25 usually the best. In the summer
months, the 16 and 19 meter day bands sometimes stay open at night.
TUNING AROUND IN THE SHORTWAVE BANDS
Refer to the previous section titled SHORTWAVE METER BAND DESIGNATOR ENTRY to get into a short-wave band appropriate for the time of day that you’re listening. Using this method will place you at the be-ginning of the band’s frequency range. Use the tuning knob described in the previous section titled MANUAL TUNING to search for stations, staying within the bands frequency range to optimize results. Alternately, use the SEEK feature described in a later section titled SEEK FUNCTION to have the Elite Satellit automatically scan and stop on shortwave stations.
AM OPERATION
For general tuning and listening on the LW, MW or SW bands, normal AM mode is
best. However, under less than ideal reception conditions, several options are
available that can improve reception.
AM SYNC (Synchronous)
Selective fading is a condition that frequently occurs on the SW bands in
which the carrier of the desired station momentarily fades away, making the
remain-ing received information difficult or impossible to understand.
This condition can frequently be improved considerably by engaging AM SYNC
mode. To do this, press the ‘AM’ soft key [Figure 5, # 50] when already in the
AM mode. You will observe “AM SYNC” flashing briefly above the ‘AM” soft key
label until the desired station is locked in. Further improvement may be
obtainable while in this mode by pressing the SSB soft key [Figure 5, # 51].
Repeatedly pressing this soft key will cycle through USB (upper sideband), LSB
(lower sideband), and DSB (double sideband) one of which may reduce adjacent
channel interference.
BW (Bandwidth)
Repeatedly pressing the ‘BW’ soft key [Figure 5, # 48] will cycle through
three IF bandwidths of 7 kHz, 4.0 kHz, and 2.3 kHz. The narrower the bandwidth
selected, the “muddier” the received signal will sound. While 6.0 kHz is the
preferred setting for best fidelity, narrower settings will sometimes improve
reception under crowd-ed band conditions by filtering out nearby interference.
AGC (Automatic Gain Control)
In AM, SW or LW bands pressing the ‘AGC’ soft key [Figure 5, #47 will turn the
AGC function On or Off.
SSB RECEPTION
SSB, single sideband, is needed to listen to certain types of signals,
including amateur radio two-way communications and Morse code (often called
CW)
FM OPERATION
FM reception is perhaps the easiest mode to use on the Elite Satellit
receiver.
The AGC and BANDWIDTH settings are not usedin FM. In fact, all of the function
soft keys along the bottom edge of the display except the ‘MENU’ soft key have
no function on FM and the labels on the dis- play for these soft keys
disappear. Attempting to use one of these soft keys will result in an ‘ERROR’
beep.
All FM stations in the U.S. end in an odd 100 kHz, i.e. 97.7 MHz, and are
spaced 200 kHz apart. The Elite Satellit receiver has the ability to tune in
100 kHz steps to allow tuning in between stations to help eliminate
interference to weaker stations that could be covered up by stronger adjacent
stations.
Additionally, when headphones are used, or if the LINE OUT jack is fed into an
external stereo sound system, true stereo reception is possible. The ‘STEREO’
indicator [Figure 5, # 44] on the display will appear when a stereo station is
tuned in. ‘MONO’ will appear
in this location if the transmitting station is not in stereo, if no signal is being received, or if MONO is selected from the AUDIO SETTINGS menu.
To select between STEREO and MONO from the AUDIO SETTINGS menu, proceed as follows:
- Press the ‘MENU’ soft key.
- Press the ‘Direct-Key-Input’ ‘2’ key or press ‘MENU’ two more times. This will access the AUDIO SETTINGS menu.
- Press the ‘Direct-Key-Input’ ‘1’ key to cycle between MONO and STEREO.
When STEREO is enabled, the receiver will automatically switch to stereo and provide left and right audio from the HEADPHONE and LINE OUT jacks when a stereo FM signal is being received. If the headphones are removed while listening to a stereo broadcast the receiver will provide monaural audio from the internal or an external speaker.
MEMORY FUNCTIONS
The Elite Satellit receiver contains 1700 memory chan-nels that can be used to store and recall commonly monitored frequencies. The first 500 of these are re-ferred to simply as MEMORY channels. The remaining 1200 are referred to as COUNTRY channels.
The 500 MEMORY channels are displayed in groups of 10 per screen and each
saved frequency can be stored with an identifying name.
The 1200 COUNTRY memory channels are divided among 111 countries from
Afghanistan to Yugoslavia with 10 memory channels assigned per country and
with 90 memory channels remaining with no country assigned. These COUNTRY
memory channels are num- bered from 501 to 1700. They are displayed in groups
of ten, and can be used to store and recall commonly mon- itored frequencies.
Unlike the MEMORY chan-nels, COUNTRY channels cannot have names assigned to
each channel.
Both MEMORY and COUNTRY channels can be scanned using the SEEK function which
can stop, or they can
be scanned selectively using the T.SCAN function. With MEMORY and/or COUNTRY
channels programmed, you can use the T.SCAN function to selectively monitor
desired frequencies. The following operating parameters may be stored in any
MEMORY or country channel: Frequency, Mode, Bandwidth, AGC setting, PBT
setting, Synchronous Detector setting.
STORING A CHANNEL
To store a channel from VFO mode proceed as follows: First select the mode and
frequency that you wish to
- store, as you normally would do in VFO mode. Make sure you have set all the function parameters to your preference.
- Then press the ‘STORE’ key [Figure1, # 9], followed by the ‘MEMORY’ or ‘COUNTRY’ soft key [Figure 5, # 54 & #52 respectively]. This will take you to the MEMORY or COUNTRY screen similar to that shown in Figure 6. Use the ‘TUNING’ knob [Figure 1, #18] or the ‘< SELECT >’ key [Figure 1, #8] to select the desired blank MEMO-RY or COUNTRY number.
- Press the ‘STORE’ key again. In ‘COUNTRY’ mode, the selected frequency will appear at the selected COUN-TRY channel in reverse video, a confirming beep will be heard and “COUNTRY STORED” will appear briefly on the display. In MEMORY mode, the chosen fre-quency will appear, in reverse video, and a flashing white curser will appear in front of the selected channel number.
- Within 10 seconds, you must either begin to pro- gram a name for the desired channel, or press the ‘STORE’ key again to store the channel without a name or to use the previously stored name.
- To name the channel, while the white curser is flashing, use the ‘TUNING’ knob to scroll through the alphanumeric characters until you find the one you want. Then press the right hand ‘
- When you have finished entering the channel name, press the ‘STORE’ key again. You will hear a confirm-ing beep and will be returned to the VFO mode.
RECALLING A CHANNEL
To select a specific MEMORY or COUNTRY channel, press the ‘MEMORY’ or ‘COUNTRY’ soft key to enter MEMORY or COUNTRY mode. This will cause the selected soft key label to appear in reverse video. Then use the ‘TUNING’ knob or the ‘< SELECT >’ key to scroll through the channel numbers.
If you know the number of the channel you want to receive, you can go to it directly by entering the num-ber on the ‘Direct-Key-Input’ keypad. If less than a four digit number is entered, there may be a slight delay between the time you enter the number and the time the channel change actually takes place. However, if you enter a four digit number, the channel change will occur immediately upon entry of the fourth number.
DELETING A CHANNEL
Select the channel to be deleted as described in
“RECALLING CHANNEL”. Press and hold the ‘ DELETE’ key [Figure 1, #
10] for 3 seconds. A high pitched beep will be heard to indicate that the
contents stored
in the selected memory channel number have been deleted, and you will see the
frequency disappear from the selected MEMORY channel number.
HD RADIO OPERATION
HD RADIO MODE
The Elite Satellit radio will automatically detect and switch to HD Radio mode to provide the highest qual-ity audio available. While the Elite Satellit will always be looking for HD Radio stations as you tune in the FM frequency band, you will not see any of these HD stations if the signal strength is not strong enough.
FINDING AVAILABLE HD RADIO STATIONS
If you know that there is an HD Radio station paired with one of your local FM
radio stations simply key in that station’s frequency when in FM mode. For
example, type in “8800” to select 88.00 MHz. Once the audio is tuned to that
frequency, if there are HD Radio stations associated, they will automatically
appear.
If you do not know your local radio station frequency press and hold the
“SELECT” button until the Elite Satellit begins to scan the FM frequencies
either upward or downward. The radio will stop once it finds a frequency with
content.
Once the Elite Satellit switches to HD Radio mode you will no longer see “FM”
under the frequency, rather you will see the letters “HD”.
FM RDS / HD RADIO DATA
HD Radio channels utilize radio data system (RDS) technology to display items such as the Artist, Music Genre, Song Name, etc. Depending on signal strength it may take up to 3 seconds for this data to appear on the screen and start scrolling.
MAIN AND SUPPLEMENTAL PROGRAM SERVICES
Some HD Radio stations will broadcast multiple channels across one frequency.
If you see the letters “MPS+” or “SPS1+” it means that there are alternative
channels available at this frequency. Once you see this text, simply turn the
tuning knob on the right to select between the Main Program Service (MPS+) or
Supplemental Program Services (SPS1+, SPS2+, SPS3+, etc.).
To find more information on the Radio Data System simply search for it in
Google on your browser or visit Wikipedia and search for it. More information
on HD Radio can be found at HDRadio.com.
SEEK FUNCTION
DESCRIPTION
The Elite Satellit incorporates a SEEK function which allows the user to
search for signals in VFO, MEMORY or COUNTRY mode which have signal strengths
that exceed a predetermined level which the user determines by the setting of
the ‘SQUELCH’ knob [Figure 1, # 15].
VFO MODE
To use SEEK in VFO mode, proceed as follows:
- Select the frequency range you would like to scan. This can be FM, MW, LW, SW or AIR.
- Press the ‘SEEK’ key [Figure 1, # 13]. The receiver will scan through the selected band in 5 kHz steps on LW band, 9 or 10 kHz steps on MW band, 5 kHz steps on SW band, and 100 kHz steps on FM band. The receiver will remain on that signal until theM ‘SEEK’ key is pressed again.
- If the receiver continues to SEEK but cannot find a signal, you may press ‘SEEK’ again to stop the SEEK.
T-SCAN FUNCTION
The T.SCAN function of the Elite Satellit allows the user to mark numerous channels in the MEMORY, and/or COUNTRY, memories for selective scanning.
MEMORY & COUNTRY MODE
To use SEEK in MEMORY and COUNTRY modes, select- ed frequencies must be programmed into several of the MEMORY and/or COUNTRY channels. Program-ming of MEMORY and COUNTRY channels is covered on page 11. Once MEMORY and/or COUNTRY chan-nels are programmed as desired, proceed as follows:
- Press the ‘MEMORY’ or ‘COUNTRY’ soft key to enter the desired mode.
- Press the ‘SEEK’ key. The receiver will step through all programmed MEMORY or COUNTRY locations until it finds a signal that exceeds the squelch set- ting. It will stop on that signal and will stay there until the ‘SEEK’ key is pressed again.
Note: Search under MEMORY or COUNTRY operates according to the following rules:
- When currently listening to the SW/MW/LW band that is not AM SYNC or SSB, the radio will only search for stations that are not AM SYNC or SSB in the SW/MW/LW band
- When listening to AM SYNC or SSB mode in SW/ MW/LW band, the radio will only search for AM SYNC or SSB station in SW/MW/LW band.
- When currently listening to the FM band, the radio will only search for stations in the FM band
- When listening to the AIR band, the radio will only search for stations in the AIR band
CLOCK & TIMER FUNCTIONS
TIME DISPLAY
The Elite Satellit incorporates dual time clocks allowing two 24 hour clocks
to be set and maintained.
The two-event timer functions are also derived from the displayed clock.
Therefore the clocks must be set first for proper TIMER operation, and the
clock select-ed for display must be the same one (GMT or Local) for which the
timers are programmed.
TIMER settings are stored in non volatile memory and are maintained regardless
of how long power has been removed.
When the receiver is in the ON state, the time is dis- played in the upper
right hand corner of the display, regardless of which menu or operating mode
is select- ed. When the receiver is in the OFF state, the time is displayed
prominently in the upper portion of the dis- play, and if either timer is
enabled, timer settings are displayed in the bottom portion of the display.
The time on the display can also be turned off manually in the menu.
If the time in any menu or display is observed to be flashing on and off at
one second intervals, it indicates that the selected clock is not set.
Selecting between Local time and GMT time is accomplished by pressing and
releasing the ‘TIME’ key [Figure 1, #14] three times. This will bring up the
CLOCKS menu, which allows the user to press the soft key along the right hand
side of the display labeled
“GMT” or “LOCAL”. When the receiver is in the OFF state, pressing the ‘TIME’
key will toggle between Local and GMT.
-
With the receiver turned on, press the ‘MENU‘ soft key which will activate the MAIN MENU. Then press the ‘6’ key on the ‘Direct-Key-Input’ keypad, to acti- vate the SYSTEM SETTINGS menu.
-
Item 3 on the SYSTEM SETTINGS menu reads: ”3 AUTO CLOCKSET OFF / FROM RDS.
You will note that either “OFF” or “FROM RDS” is shown in reverse video. Pressing ‘3’ on the ‘Direct-Key -Input’ keypad, will toggle the reverse video curser between “OFF” and “Auto set from rds”. If necessary,press the ‘1’ key to move the curser to “FROM RDS”. -
Item 3 on the menu reads: “LOCAL TIME OFFSET — /+”. This refers to whether or not your Local time is less than or greater than GMT. For example, the Western hemisphere is less than GMT and the East-ern hemisphere is greater. Therefore, if you lived in the Western hemisphere, you would use the ‘3’ key to toggle the curser to ‘ – ‘.
-
Item 4 on the menu reads “LOCAL TIME OFFSET 00:00 HOURS”. This refers to how much your local time is offset from GMT. For example, in the East-ern Time Zone of the USA the offset is 5:00 hours.
- To change this setting, press ‘4’ on the ‘Di-rect-Key-Input’ keypad. This will highlight the off-set time.Use the ‘Direct-Key-Input’ keypad keys to enter the desired offset, ignoring the colon.
- Use the ‘Direct-Key-Input’ keys to enter the desired offset.
- Press the ‘STORE’ key to save, the offset will no longer be highlighted.
- Press the ‘9’ key to exit and return to normal operation.
SETTING THE 24 HOUR CLOCKS MANUALLY
If you are not in a location where adequate signal quality can be obtained on one of the RDS signals, the Local and GMT clocks will need to be set manually. This is accomplished using the SET CLOCKS menu. To reach this menu, the unit must be in the ON state. Then press the ‘MENU’ soft key. This will bring up the MAIN MENU. From the MAIN MENU, press the ‘3’ key on the ‘Direct-Key-Input’ keypad. This will activate the SET CLOCKS menu.To use SEEK in VFO mode, proceed as follows:
Setting Local Time
-
To set the Local time, press MENU, SET CLOCKS and then press the ‘1’ key. This will highlight the 4 digits on the right side of the LOCAL TIME SET. Enter the current local time using the keypad and press STORE to save.
-
Using the ‘Direct-Key-Input’ keypad, key in the desired time, ignoring the colon. (HINT: Key in a time about one minute ahead of the actual time and wait.)
Example: For 16:05, press in sequence ‘1’, ‘6’, ‘0’, ‘5’. The Local time set line on the display will now appear as: “ LOCAL TIME SET 16:05 “ -
When the actual time agrees with the displayed time, press the ‘STORE’ key. The entered time will now be shown, the menu numbers will return, and the clock will begin running.
-
To exit the SET CLOCKS menu, press the ‘9’ key on the ‘Direct-Key-Input’ keypad.
-
Note that after setting the Local Time the GMT time will update accordingly per the offset “+” or “-“ in menu item 3 and the hour offset in menu item 4.
Setting GMT Time
-
To set the GMT time, press MENU, SET CLOCKS and then press the ‘2’ key. This will highlight the 4 digits on the right side of the GMT TIME. Enter the current local time using the keypad and press STORE to save.
-
Using the ‘Direct-Key-Input’ keypad, key in the desired time, ignoring the colon. (HINT: Key in a time about one minute ahead of the actual time and wait.)
Example: For 16:05, press in sequence ‘1’, ‘6’, ‘0’, ‘5’. The Local time set line on the display will now appear as: “GMT TIME SET 16:05 “ -
When the actual time agrees with the displayed time, press the ‘STORE’ key. The entered time will now be shown, the menu numbers will return, and the clock will begin running.
-
To exit the SET CLOCKS menu, press the ‘9’ key on the ‘Direct-Key-Input’ keypad.
-
Note that after setting the GMT the LOCAL time will update accordingly per the offset “+” or “-“ in menu item 3 and the hour offset in menu item 4.
NOTE: If the AUTO CLOCK SET is left in the ON state, then manual setting of the clock may result in only a temporary change of the time settings.
TIMER OPERATION
The Elite Satellit includes two programmable event timers allowing the
receivers to turn ON or OFF at preset times The timers may be used separately
or together and may recall a currently displayed frequency, MEMORY channel,
COUNTRY channel, or a combination of those.
In addition, programming only an OFF time
provides a Sleep timer, and programming only an ON time provides a Wake timer.
Note that the timers, when activated, respond to the last displayed clock.
Programming the timers is a three step process. Step one is to set the ON
time, and step 2 is to assign the OFF time. Step three is to assign a MEMORY,
COUN- TRY channel to a timer.
Setting Timer On/Off Times
Enter the TIMERS menu by pressing the ‘MENU’ key to reach MAIN MENU, and then pressing the ‘5’ key on the ‘Direct-Key-Input’ keypad. This brings up the TIMERS menu.
- Press ‘1’ on the ‘Direct-Key-Input’ keypad. This will cause the menu numbers on the left to disappear and the ON time entry for TIMER 1 will turn to reverse video, as shown here: “TIMER 1 ON TIME 11:30 “
- Key in the desired ON time for TIMER 1, ignoring the colon. For example, for an ON time of 18:41, press the following keys: ‘1’, ‘8’, ‘4’‘1’. The TIMER 1 ON TIME curser will now show “ 18:41 ”.
- Press ‘STORE’ to save the TIMER 1 ON time in memory. You will hear a beep, the reverse video window will change to normal video, and the menu numbers will return. To set the OFF time for TIMER 1, select item 2 from the menu by pressing ‘2’ on the ‘Direct-Key-Input’ keypad and follow the same procedure as you used to set ON time.
Setting A Wake Or Sleep Timer
If you want a timer to act as a wake timer only, you would program an ON time
and clear an OFF time. This will cause the receiver to turn on at the
designat-ed time and stay on until turned off manually. If you want the timer
to act as a sleep timer only, you would clear any existing ON time and program
an OFF time. This will cause the receiver to turn off at a desig-nated time
and stay off until turned on manually. To program only an off time, or only an
on time, clear the unwanted time on the selected timer as follows:
- Select the timer ON time or OFF time to be cleared by pressing the ‘Direct-Key-Input’ keypad key corre- sponding to the menu number of the desired timer ON time or OFF time. This will cause the menu num- bers to disappear and a reverse video curser to appear on the selected timer ON time or OFF time.
- Press the ‘CLEAR/LOCK’ key on the ‘Direct-Key- Input’ keypad. This will cause the numbers in the reverse video curser to disappear. Only the colon will remain.
- Press ‘STORE’. This will cause the reverse video curs-er to disappear, a beep will be heard, the menu numbers will reappear, and the null time informa- tion will be stored in memory.
Setting Timer Memory Channels
To tie a timer to a stored channel press the number that relates to the Timer
MEM CH and select the memory channel to be associated with the timer.
Enabling/Disabling Timer Operation
Press the ‘TIME’ button. This will activate the TIMER 1 display. This
display shows the start time and stop time set for TIMER 1 as well as the
MEMORY or COUNTRY menu number, frequency, and name (if any) programmed in for
the TIMER 1 MEM CH.
To enable TIMER 1, press the ‘ENABLE’ soft key. This will cause “TIMER 1” to appear in the upper right-hand corner of this display (as well as all other displays and menus), indicating that TIMER 1 is enabled. To disable TIMER 1, press the ‘DISABLE ’ soft key. If TIMER 1 was the only one enabled, “TIMER 1” will disappear from the display. If TIMER 2 was also enabled, only the ‘1’ will disappear. If both timers are enabled you will see “TIMER 1 2” in the upper right-hand corner of this and all other displays and menus.
To enable or disable TIMER 2, press the ‘TIME’ key again. This will activate the TIMER 2 display. This display is identical to the TIMER 1 display except for its name. Follow exactly the same procedure to enable or disable TIMER 2.
To return to normal operation from the TIMER 2 display, press the ‘TIME’ key twice. The first press will take you to the CLOCKS display, and the second will take you back to the VFO, MEMORY, and COUNTRY display. Note that repeatedly pressing the ‘TIME’ key will cycle through the TIMER 1, TIMER 2, CLOCKS , and normal screens.
MISCELLANEOUS FUNCTIONS SNOOZE
When the receiver is ON, or turned on by the timer, pressing the “SNOOZE” bar
[Figure 3, #33] will activate the SNOOZE mode, causing the receiver to turn
off. An internal counter will automatically count down the time for 5,10, 20
or 30 minutes later, after which the radio will turn back on.
To set the amount of time for the SNOOZE function press ‘MENU” key, then
press ‘3’ to enter the SET CLOCKS menu and then press ‘5’ to select
(highlight)
the amount of time for the SNOOZE delay. Press ‘9’ to exit. When the radio is
in SNOOZE mode you can cancel the SNOOZE early by powering the radio OFF and
back ON with the POWER button. When the SNOOZE feature is active the word
SNOOZE will appear on the display with a countdown timer in the lower left
corner.
SLEEP
When the receiver is OFF, and not in SNOOZE mode, a long press of the
SNOOZE/SLEEP bar will activate the SLEEP timer. Upon activation the radio will
turn ON for the default timing of 15 minutes prior to turning OFF.
To change the amoubt of time for the SLEEP timer from the default to any other
setting of minutes, between
1 and 99, turn the radio OFF, press and release the SNOOZE/SLEEP bar and then
rotate the TUNING knob.
Once the desired number of minutes is shown on the screen press and release the SNOOZE/SLEEP bar again and / or wait for 15 seconds and the SLEEP time will automatically be entered. When the SLEEP feature is active a countdown timer will appear in the lower left hand corner of the display.
DISPLAY LIGHTING
Pressing the ‘LIGHT’ key [Figure 3, # 32] while the receiv-er is turned ON
cycles the display illumination through four backlight states; Off, Orange,
Green and Blue.
If the Elite Satellit is operating from batteries, the display will be lit
only briefly when the unit is turned OFF. If, when OFF, the ‘LIGHT’ button is
pressed once, the display will illuminate for 10 seconds and then go out. In
the ON state, the display will be lit only briefly following control inputs.
However, holding down the LIGHT key for 3 seconds will override the time out
and allow the light to remain on continuously when the receiver is ON.
The user must keep in mind, however, that keeping the light on continuously
when operating on batteries will considerably reduce battery life.
Advanced settings for the backlight can be found by pressing MENU and then the
‘5’ key to enter the BACK-LIGHT SETTINGS menu.
- Pressing ‘1’ when in the BACKLIGHT SETTING menu will cycle the backlight between each of the three colors.
- Pressing ‘2’ when in the BACKLIGHT SETTING menu will set the amount of time that the backlight stays on, in minutes, when the radio is powered on, operating from battery power after the last button has been pressed. Note that longer time settings will drain the battery more quickly.
- Pressing ‘3’ when in the BACKLIGHT SETTINGS menu will set the amount of time that the backlight stays on, in minutes, when the radio is powered on, operated from the AC/DC power adapter after the last button has been pressed.
The user must keep in mind, however, that keeping the light on continuously when operating on batteries will considerably reduce battery life.
Additional System Settings
Pressing “MENU” and then the ‘6’ key allows the user to enter the SYSTEM
SETTINGS menu. Inside this menu the user can:
Press ‘1’ to set whether the LCD stays on when the radio is in standby mode
when powered by batteries. This allows the clock to be seen on the LCD display
in standby mode. Note that this setting will cause the batteries to drain more
rapidly.
LOCK ALL ENTRY TO KEYPAD
The receiver front panel keys with the exception of the ‘CLEAR/LOCK’ key may be locked or disabled by press- ing and holding the ‘CLEAR/LOCK’ key for 8 seconds. An acknowledging beep will be heard, and both “ LOCK ” and “ TUN LOCK ” will appear on the front panel display after 8 seconds to indicate that the front panel keys and ‘TUNING’ control are locked. Press the ‘CLR/LOCK’ again for 8 seconds to unlock the front panel keys and ‘TUNING’ control. The beep will again be heard when the key is pressed and the “ LOCK ” and “ TUN LOCK ” indications on the front panel display will disappear after 8 seconds, indicating that the ‘TUNING’ control and front panel keys have been released.
This control can also be used when the receiver is turned off. Press ‘CLEAR/LOCK’ for 8 seconds. A message will appear confirming lock. If power is then pressed, a “Press CLEAR/LOCK for 8 seconds to unlock” message will appear. The user must perform this action before the ‘POWER’ key will allow the receiver to be turned on.
LINE IN
This 1/8” diameter stereo jack [Figure 2, # 24] is used to feed in audio from an external source such as a CD or cassette tape player. The input level should be approximately 300 mV, at an impedance of 47K ohm. This input is enabled when the AUX mode is selected by pressing the FM/AUX soft key twice [Figure 5, # 58]. When in this mode, the VOLUME, BASS and TRE- BLE controls are effective.
LINE OUT
This 1/8” diameter stereo jack [Figure 2, # 25] pro- vides a constant low-
level audio source that is independent of the front panel ‘VOLUME’, ‘TREBLE’
and ‘BASS’ control settings. It is designed to interface to a tape recorder,
CW / RTTY demodulators, stereo amplifiers, etc.
HEADPHONE
This connector [Figure 2 # 31] accepts a 1/8” (3.175 mm) stereo/mono headphone
connector. Stereo reception is possible only in the FM Radio mode.
All speaker outputs are automatically switched off when using the headphones.
TROUBLESHOOTING
Problem | Probable Cause | Solution |
---|---|---|
No front panel display or light. | (A) Power connection. |
(B) Defective AC ADAPTER unit.
(C) Batteries are discharged or not installed for portable operation, no AC power.
(D) Light turned off with ‘LIGHT’ key.
| (A) Check power supply cables.
(B) Check AC ADAPTER.
(C) Check/install batteries for portable operation.
(D) Turn light on with ‘LIGHT’ key.
No signals heard when antenna is connected or sensitivity is low.| (A) Incorrect antenna input selected. (B) Squelch set too high.| (A) Select correct antenna input.
(B) Set Squelch to lower level.
Signal Strength indication but no sound heard.| (A) Improper mode selected.
(B) External speaker connected but defective.
(C) Squelch set too high.
| (A) Check mode selection.
(B) Check external speaker.
(C) Set Squelch to lower level.
No front panel operation such as tuning, frequency entry, etc.| (A) Lock
enabled.| (A) Press ‘CLEAR/LOCK’ and hold for 3 seconds to unlock front panel.
Timer does not operate.| (A) Clock(s) not set.
(B) Timer not properly set.
(C) Alternate clock selected.
(D) Timer(s) not enabled.
| (A) Set clock(s).
(B) Set clock(s) and program timer ON/OFF times.
(C) Check that last displayed clock is the desired one for timer event.
(D) Enable timers. Observe TIMER 1 or 2 on display.
SUGGESTED REFERENCES
Passport to World Band Radio
Published by:
International Broadcasting Services, Ltd.
P. 0. Box 300
Penn’s Park, Pennsylvania 18943 http://www.passband.com/
World Radio TV Handbook
Published by:
Billboard Publications Inc.
1515 Broadway
New York, NY 10036 http://www.wrth.com/
The ARRL Antenna Book
Published by:
The American Radio Relay League
225 Main Street
Newington, CT USA 06111
Copyright © 1988 by The American Radio Relay League Library of Congress
Catalog Card Number: 55-8966 http://www.arrl.org/catalog/?item=9043
The ARRL Handbook
Published by:
The American Radio Relay League
225 Main Street
Newington, CT USA 06111
Copyright © 1989 by The American Radio Relay League Library of Congress
Catalog Card Number: 41-3345 http://www.arrl.org/catalog/?item=1964
WARRANTY REGISTRATION
To ensure full warranty coverage or product updates, registration of your Etón
product should be complete as soon as possible after purchase or receipt.
To register your radio, please select one of the following methods:
-
Register by visiting our website at
http://www.etoncorp.com -
Mail your registration information to the following address:
Etón Corporation 1015 Corporation Way Palo Alto, CA 94303
PRODUCT REGISTRATION
Include your name, full mailing address, phone number, model purchased, date
purchased, retail vendor name, and product serial number (typically located in
or near the battery compartment).
LIMITED WARRANTY TO THE ORIGINAL CUSTOMER
LOCK ALL ENTRIES TO THE KEYPAD
This Etón brand product, as supplied and distributed by Etón Corporation
(Etón) is warranted by Etón against manufacturing defects in material and
workmanship for the following limited warranty period:
ONE (1) YEAR PARTS AND LABOR
This limited warranty begins on the original date of purchase and is valid
only on products purchased through an authorized Etón retailer and does not
include transportation, installation, removal or reinstallation. Warranty
repairs must be performed by Etón or Etón’s authorized service center. To
receive warranty service, the original dated bill of sale must be presented
upon request as proof of purchase to Etón or Etón’s authorized service center.
Transportation to Etón or Etón’s authorized service center is the
responsibility of the purchaser.
Etón will repair or replace this product, at our option and at no charge with
new or reconditioned parts, if found to be defective during the limited
warranty period specified above. The product must be returned no later than 15
days beyond the expiration of the warranty period with transportation charges
prepaid to Etón or Etón’s designated service center for warranty coverage.
Prior to returning any product for warranty service, the purchaser must
contact Etón for problem determination and service procedure. All replaced
parts and products become the property of Etón. Replacement parts and products
assume the remaining original warranty, or ninety (90) days, whichever is
longer.
This limited warranty covers manufacturing defects in material and workmanship
encountered in normal, non-commercial use of this product and shall not apply
to the following, including, but not limited to: damage that occurs due to
applications and uses for which the product was not intended; failures or
problems which are caused by products or equipment not supplied by Etón;
accidents, misuse, abuse, neglect, misapplication, fire, water, lightning, or
other acts of nature; incorrect line voltage, fluctuations or surges; damage
caused by improper or faulty installation
(including batteries, which may create an acid leak with irreversible circuit
damage); damage caused by acid leakage; product alteration or modification; or
use of unauthorized parts, supplies, accessories, or equipment which damage
this product or result in service problems.
SERVICE INFORMATION
SERVICE YOUR Etón PRODUCT
To obtain service for your Etón product we recommend first contacting an Etón
service representative at
800-872-2228 US,
800-637-1648 Canada or
650-903-3866 for problem determination
and troubleshooting. Many of the common questions can be resolved quickly over
the phone.
There are two service types should your Etón or product need repair.
-
WARRANTY –
If your product is still in warranty and the Etón service representative determines that warranty service is needed, a return authorization will be issued and instructions for shipment to an authorized warranty repair facility. Do Not ship your radio back without obtaining the return authorization number. -
NON-WARRANTY –
If your product is no longer under warranty and requires service our technical staff will refer you to the nearest repair facility that will be able to best handle the repair.
1-800-872-2228 from the U.S.
1- 800-637-1648 from Canada
1- 650-903-3866, worldwide
FAX: 650-903-3867
customer_service@etoncorp.com
www.etoncorp.com
Etón Corporation
1015 Corporation Way
Palo Alto, California 94303 USA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>