saxby 80497 Extrusion Slim Surface Profile 2m Length Instruction Manual
- June 4, 2024
- saxby
Table of Contents
Instruction manual
EXTRUSION
80497, 80498, 80499, 80500, 80501, 94946, 94947, 94948, 94949 97732, 97734, 97735, 97736, 97737, 97738, 97739, 102665, 102666, 102667, 102668
Thank you for purchasing this accessory. Please read the instruction carefully
before use to ensure the safe and satisfactory operation of this product.
Please retain these instructions for future reference.
Specification – Dimensions:
Surface –
80497: 2000mm x 17mm x 9mm
94946: 2000mm x 17mm x 9mm
80498: 2000mm x 16.5mm 13.5mm
97734: 2000mm x 17mm x 9mm
97735: 2000mm x 23.5mm x 11.2mm
97738: 2000mm x 23.5mm x 21.5mm| Recessed –
94947: 2000mm x 21.7mm x 6mm
80499: 2000mm x 23.1mm x 13.4mm
102666: 2000mm x 21mm x 13.5mm
97736: 2000mm x 30.7mm x 11.2mm
97739: 2000mm x 30.0mm x 21.5mm| Bendable –
97732: 2000mm x 18mm x 5mm
Corner
-80501: 2000mm x 16mm x 16mm
97737: 2000mm x 30mm x 30mm
102668: 2000mm x 61mm x 61mm| Plaster-in – 80500: 2000mm x 56.9mm x
15.4mm
94948: 2000mm x 64mm x 14mm
94949: 2000mm x 100mm x 19.6mm
102665: 2000mm x 100mm x 29.6mm
102667: 2000mm x 95mm x 40mm
---|---|---|---
Installation for Surface / Recessed / Bendable / Corner
- Choose an ideal place to mount the profile.
- Remove the 4 brackets from the fixing pack.
- Using the brackets as templates, mark and drill the position of the fixing holes.
- Ensure the mounting structure is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes.
- Attach both brackets to the chosen mounting surface using the plastic plugs and screws (not supplied) according to the following installation diagram.
- Remove the backing off of the chosen LED module strip and stick it down inside the aluminum profile.
- Attach the diffuser to the profile, sliding into the profile grooves.
- Place end caps onto the ends of the fitting.
- Push the profile onto the brackets to secure.
- Your fitting is now ready for use.
Installation for Plaster-in
- Using the aluminum profile as a template, mark and drill the position of the fixing holes.
- Ensure the mounting structure is capable of holding the weight of the product. Take care to avoid damaging any concealed wiring and pipes.
- Remove the backing off of the chosen LED module strip and stick it down inside the aluminum profile.
- Attach the diffuser to the profile, sliding into the profile grooves.
- Place end caps onto the ends of the fitting.
- Push the aluminum profile into the existing groove.
- Then use the plastic plugs and screws (not supplied) to fix the aluminum profile to the wall.
- Cemented the sides of the aluminum profile.
Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive
cleaners as these could damage the finish.
For your safety, always switch off the power supply before changing
lightbulbs, or cleaning.
V5 12/05/2022
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
UK Manufacturer: BH17 7BY
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>