NODOR 8551 NorBreeze Eclipse 90 bk Instruction Manual
- October 29, 2023
- NODOR
Table of Contents
NODOR 8551 NorBreeze Eclipse 90 bk
Product Information
The product is an extractor fan that comes with three or four speed buttons and a MAX button. The MAX speed only works for 5 minutes after which it automatically decreases to the 3rd speed. The product has an aluminium filter that needs to be cleaned regularly for optimum performance. The product also has a carbon filter that needs to be fitted for recirculation mode or replaced if it is full of grease. The product comes with an optional vent kit that needs to be fitted according to the manufacturer’s instructions.
Product Usage Instructions
Before carrying out any maintenance work, always switch off the electricity supply. Do not use abrasive cleaning products and solvents for cleaning the outside of the hood. Use liquid, non-corrosive detergent instead. Do not use high-pressure or steam cleaning devices.
If you face any issues with the product, refer to the FAQ section in the manual. If the problem persists, contact the technical service or your distributor.
To use the extractor fan, press the speed buttons to select the desired speed. If your panel has a MAX button, press it to activate the maximum speed. The MAX speed will work for 5 minutes after which it will decrease to the 3rd speed automatically.
Clean the aluminium filters regularly for optimum performance. If you are using the product in recirculation mode, fit a carbon filter or replace it if it is full of grease. Check that the hood is connected to power and that the fuses or automatic have not jumped. If you face suction performance issues, select a higher speed and clear any obstruction from the top vent. Ensure that the vent kit is fitted according to the manufacturer’s instructions.
IMPORTANT – Please read carefully the separate safety guide before use.
USE
| Filter clean warning display/button. Warning of the need to replace the
filter – press to deactivate once the filter has been cleaned or replaced.
| Enable and disable extractor fan timer.
Timer: the extractor fan works for 5 min. at the current speed and another 5
min. at each of the lower speeds until it stops.
| Lighting on and off. Keep pressed down to adjust the lighting
intensity.
| Extractor fan on and off.
| Extractor fan speed – button: speed 1, 2 and 3/4. In panels with MAX
button, MAX speed only will work during 5 minutes, once it runs out, the speed
will decrease to 3rd speed.
CARE & MAINTENANCE
Warning: always switch off the electricity supply before carrying out
maintenance work on the hood. In the event of a fault, contact an official
distributor or authorised dealer.
Cleaning the outside: use liquid, non-corrosive detergent and avoid using
abrasive cleaning products and solvents.Do not use high-pressure or steam
cleaning devices.
Important: increase the filter cleaning/replacement frequency if the hood is
used for more than 2 hours a day. Always use genuine filters from the
manufacturer.
Grease cleaning
To avoid fires, clean thoroughly once a month or whenever the display pilot
light indicates as such. To do so, remove the filters and wash with hot water
and detergent. If using a ishwasher (metal parts may turn black without this
affecting their functional capacity), load the filters vertically to avoid
solid residue from being deposited.
MONTH
FAQS
| Problem | Possible cause | Solution |
|---|---|---|
| Excessive vibration. | The appliance is not installed properly on the | |
| brackets. | Take down the appliance and check it is properly fixed. | |
| The fan blade is damaged. | Switch off the appliance. Repair to be carried out |
by qualified service personnel only.
The fan motor is not fixed tightly.
The light is on, but the fan does not work.| The fan blade is jammed.
The motor is damaged.
Both the light and motor do not work.| Light bulb blown.| Contact Customer
Services on.
Power connection loose.| Check power supply.
Suction performance reduced.| Speed may be too low.| Select a higher speed.
Aluminium filters are dirty.| Clean the aluminium filters. (See
Care and maintenance section).
Top vent might be obstructed.| Clear any obstruction.
Optional vent kit might be twisted.| Ensure that the vent kit is fitted
according to the manufacturer’s instructions.
The installation may not comply with the manufacturers instructions.| The vent
hose should be correct diameter throughout with no reductions or
restriction.(See installation section).
Works normally but cooking smells linger.| Carbon filter is not fitted in
recirculation mode or is full of grease.| Fit carbon filter or replace the
carbon filter (See Care and maintenance section).
The hood does not work.| Check that the hood is connected to power. Check that
the fuses or automatic have not jumped.
The hood still does not work.| If, after having checked the points mentioned
above, your problem has not yet been solved, contact the technical service or
your distributor.
tel.: +(36-1) 427 0325, +(36-1) 427-0326; fax: +(36-1) 427 0327
www.multikomplex.hu
CATA ELECTR0D0MESTIC0S, S.L.
0ficinas: c/ Anabel Segura, 11, Edif. A, 3a pl. 28108. Alcobendas. Madrid.
Espana
Fabrica: c/ del Ter 2, Apdo. 9. 08570. Torell6.Barcelona. Espana
T . +34 938 594 100 – Fax +34 938 594 101
www.cnagroup.es –
cna@cnagroup.es
Atencion al Cliente: 902 410 450 / +34 938 521 818 –
info@cnagroup.es
SAT Central Portugal: +351 214 349 771 –
service@junis.pt