FOSHAN FSLA19-5-ZL Smart Led Bulb User Manual

: June 9, 2024
: Foshan

Table of Contents

FOSHAN FSLA19-5-ZL Smart Led Bulb
Product Specification
- Alexa Voice Control
How to Connect Alexa with Bluetooth Light Bulb
FCC Compliance Statement
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FOSHAN FSLA19-5-ZL Smart Led Bulb

Product Specification

Lumen: 800LM
Voltage: AC1 IOV-130V (Do not use dimmer)
Power: 9W
Lifespan: > 15000H
Frequency: 50-60Hz
Colour Temperature: 2700K-6500K+RGB
Control Method: Echo or Alexa App

Alexa Voice Control

This product is an Alexa-Local-Connected device via bluetooth.
It is much easier to use than WiFi deviæ.

Use Accessories :

Echo Speaker ( 3rd Generation or above)
“Amazon Alexa ” App(can be download at app store)
Set up the Echo speaker and make sure Alexa APP can work with the Echo speaker.

How to Connect Alexa with Bluetooth Light Bulb

Simple steps to connect to Alexa:

Make sure the Echo speaker is successfully connected to the Amazon Alexa APP. Make sure Echo is near bulb when pairing. You can move them apart after pairing.
To reset the smart bulb, please slowly repeat ‘power on and power off’ for 3 times. Every time the ‘ON/OFF’ state should keep 2 to 5 seconds.When the bulb breaths 3 times,it indicates that the reset is successful.lf the bulb does not blink, please repeat the process.
Just speak to Echo speaker ‘ Alexa, discover(or find) device.’ Then Echo will start searching the new device.
Echo will report when it connects new device successfully.
When the bulb sucessfully connect with Alexa, the light will become another white. Alexa will name the bulb automatically (e.g. First Bulb). You can change the bulb’s name on “Amazon Alexa” App.

Some of Alexa Voice Commands:
Wake Word: Alexa (wake up the Echo speaker) On/Off Control Command: Turn on the AAA/Turn off the AAA (AAA: device name)

Color Control Command: Turn AAA to “B” (AAA: device name; B: color)
Brightness control command: Turn AAA brightness to device name; B%: Brightness Percentage)

Note

Please notice that if the bulb is connected with the “Marvelight” App, the bulb will unable connect with Alexa. If you want to control the bulb with Alexa, please make sure you close the “Marvelight” so the bulb will not be automatically connected with the app.
The bulb should be within 20 meters from Echo without obstruction. Better to be in one same room. Please aware that bluetooth is not good at penetrating walls. You can try stablity, if not good, put bulb and Echo closer.
Use Alexa APP ‘room’ to group control lights.
Use Alexa APP ‘routine’ to do more control.
Do NOT search brand on Alexa APP. Just ‘find device’.
Sometimes device may be pushed offline by Alexa.Just ‘find device’ to reconnect it.
This device does NOT support google assistant.
The bulb is dimmable by Alexa. Not external dimmer.

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference;
This device must accept any interference received, including interference that may cause undesired operation.

Waming: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against hamful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.