PHILIPS BY240Z Highbay Sensor Instruction Manual
- June 9, 2024
- Philips
Table of Contents
PHILIPS BY240Z Highbay Sensor
INSTALLATION
Features
12NC
|
Description
|
Power supply
|
Dim control output
|
Transmission power
|
Detection radius
|
Mounting height
|
Temperature
|
IP rating
---|---|---|---|---|---|---|---|---
911401892082
|
BY240Z Highbay Sensor
|
12V-24V DC
＞50mA
|
0-10V,max
25mA sinking current
|
＜0.2mW
|
20%/50%/75%/
100%(1-8m)
|
Max 40ft. (12meters)
| -30℃~45℃|
IP65
Product Information
The BY240Z Highbay Sensor is a product from Koninklijke Philips N.V. It is a highbay sensor that operates on 12V-24V DC with apower consumption of 50mA. The sensor has a dim control output of 0-10V with a maximum sinking current of 25mA. It has a transmission power of 0.2mW and a detection radius of up to 40ft (12meters) with sensitivity options of 100%, 75%, 50%, and 20%. The mounting height range for the sensor is 13-40ft and it has an IP rating of IP65 making it dust-tight and protected against water jets.
Dimensions
The dimensions of the sensor are as follows:
- Length: 43mm
- Width: 51mm
- Depth: 41.3mm
- Mounting Thread: G1/2
Product Usage Instructions
Mounting
The sensor must be screwed tightly before use. The mounting height range
for the sensor is between 13-40ft.
Sensor Default Settings
The default settings for the sensor are:
- Brightness Sensitivity: 100%
- Hold Time: 5 minutes
- Daylight Sensor: Disabled
- Stand-by Dim: 30%
- Stand-by Period: 60 minutes
| Brightness | 100% | Daylight sensor | Disabled |
|---|---|---|---|
| Sensitivity | 100% | Stand-by Dim | 30% |
| Hold Time | 5min | Stand-by period | 60min |
Height
| Rang Radius
---|---
Sensitivity 100%| Sensitivity 75%| Sensitivity 50%| Sensitivity 20%
12m| 6| 4| 0| 0
10m| 7| 5| 2| 0
8m| 8| 6| 4| 2
Note: The warm-up time for the sensor is 15 seconds. After the sensor is connected to input power for the first time, the light will remain on for 15 seconds before dimming to work normally. Any settings changed by remote control will result in the LED light that the sensor connects to turning on/off as confirmation. The above data was obtained by the 1.7m tall tester walking at 0.8M/S in an open environment. Different environments,different walking speeds. There will be be deviations in the data.
Warning
It is important to note that the data provided was obtained by a tester walking at 0.8M/S in an open environment. Different environments and walking speeds can cause deviations in the data. Additionally, it is important to consider the speed of movement and the installation environment when using the sensor.
- Installation must be carried out by a licenced electrician and in accordance with these instructions and relevant Australian and New Zealand standards and local regulations.
- Ensure input voltage conforms within product specifications.
- Ensure wires are securely connected.
- Before switching on,ensure all wires are correctly connected.
- The warranty is void if product is not installed according to the instructions.
- The installation distance, both transverse and longitudinal, should be greater than 3m. If the installation distance is too close, individual lamps may be misfit.
- Installation location shall be away from WIFI，omnidirectional antennas for mobile communications,small base stations for telecommunications, TV antennas, etc. Signal source too close may disable the dimming function.
- The luminaire should not be installed on vibrating surfaces, otherwise the sensor is easy to be triggered by mistake.
- The dimming function of luminaire might be effected by the objects with vibration in its sensing area.
- The product has good penetration effect on plastic and wood. Avoid metal shielding around the antenna, which will reflect and block microwave and affect the actual induction effect;
- Walls, glass and ceramics will bring reflection and penetration attenuation of electromagnetic waves,and reduce the sensing distance of the sensor. The thicker the material, the more severe the attenuation will be.
- The movement of animals and objects within the sensing range may cause the light to turn on, which is a normal phenomenon.
- The electromagnetic wave emitted by microwave sensor in the practical application environment,the different reflectivity of obstacles will lead to different induction range, which is a normal phenomenon.
- The light sensitivity threshold is in a sunny environment, no shadow and ambient light diffuse reflection..Ambient lux level could be different in different environment, weather, climate, time-of-day and season.
- The parameters of the sensor may need to be reconfigured in different installation environments. Please refer to the following instructions or contact the manufacturer.
- Sensing distance will be affected by the installation height of the sensor, the size of the object to be detected, the speed of movement, the installation environment
Note
- Warm up time is 15 seconds. After the sensor connects input power first time,the light will keep on for 15 seconds,then go to dimming to work normally.
- Factory Default Setting:100% sensitivity，Dimming level:30%，Dimming time: 60 minitues.
- Any setting changed by remote control，the led light that sensor connect will on/off as confirm.
Distributed by:
Reduction Revolution Pty Ltd
www.reductionrevolution.com.au/LED