PHILIPS Lucca Outdoor Wall Light User Manual
- October 27, 2023
- Philips
Table of Contents
PHILIPS Lucca Outdoor Wall Light
IMPORTANT SAFETY INSTRUCTIONS
Product appearance may vary from image shown.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH
THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
DANGER – RISK OF SHOCK – DISCONNECT POWER BEFORE INSTALLATION.
Wire Connectors Instructions
- Turn off power before fnstall1ng or removing connectors.
- Strip wires 5/16″(7.9mm). For #16 and smaller wires, strip 3/8″(9.5mm).
- Pre-twisting is unnecessary, hold stripped wires together with ends even. Lead stranded wires slightly.
- Align any frayed strands or conductors.
- Push wires into connector and screw on until two twists are visible in wires.
For use with copper-to-copper conductor
Temperature Rating: 105°C(221 °F) Max.
Voltage Rating: 600V Max. buliding wiring; 1000V Max. in fixtures and
signs
Listed as a PRESSURE-TYPE wire connector on the following Solid and /or
Stranded wire combinations:
For UL Listed, CSA and CQC Certified
INSRUCTIONS
SAFETY INSTRUCTIONS
The manufacturer advises the correct use of Luminaires (lighting fixtures)! Therefore always follow these instructions to ensure correct and safe Installation and functioning of the luminaire and keep it for future reference. Turn off electrical power at main fuse or circuit breaker box before commencing installation, maintenance or repair. If in doubt, consult a qualified electrician or contact your retail outlet. Ensure that you always install the luminaire to the local electrical code. Certain regulations indicate that luminaires should be Installed by a qualified electrician. Observe the correct color of the wiring before installation: white (N), black (L) and green or bare copper wire (Ground). Do not connect this luminaire to a non-grounded electrical system.
WARNING: Installing this fixture in a non-grounded electrical system could allow metal parts of the lumlnaire to carry electrical current If any wires or wire connections become broken or loose. Under this condition, anyone coming in contact with the luminaire is subject to electric shock which could cause injury or death. Always use wire nuts/connectors rated for the correct gauge and number of wires used.
CAUTION: Be certain that no bare wire strands are exposed outside of the wire nuts/connections (if applicable). Be careful not to damage or cut the wire insulation (covering) during installation.
Do not permit wires to contact any sharp edges. Do not remove thermal
insulation pad(s). Doing so will result in increased temperatures and possible
risk of fire. Maintain Interior lighting with a dry cloth duster. do not use
abrasives or solvents.Avoid liquid on all electrical parts. Always consider
all the technical specifications of the luminaire.Verify the stated icons on
the identification label on the luminaire and the icons that are shown in part
A
of your safety instructions.
ATTENTION: Below you will find all the explanations with numeric reference to the icons respectively in front of these PART- B safety Instructions. Applicable icons to your fixture are shown in PART- A safety Instructions.
-
This product should only be installed indoors.
-
The product is suitable for outdoor usage.
-
Only suitable for dry locations.
-
Suitable for damp locations.
-
Suitable for wet locations.
-
Luminaire is suitable for base up mounting.
-
Luminaire is suitable for base down mounting.
-
Luminaire is suitable for horizontal mounting.
-
The luminaire is only suitable for fixing to the ceiling.
-
The luminaire is only suitable for fixing to the wall.
-
The luminaire is suitable for fixing to the wall and to the ceiling.
-
Always observe the minimum distance between the lamp and the surface being lit as indicated on the icon.
-
Free air space of at least 4 inches must be kept between top of shade and bottom of canopy.
-
Immediately replace a cracked or broken safety glass and use only manufacturer approved parts.
-
Strip the wire as indicated in the diagram.
-
Use heat-resistant cable for wiring the luminaire into the mains.
-
MAX . … W: only use lamps suitable for this luminaire and keep within the maximum specified wattage.
-
This product is not suitable for children under 14 years.
-
The Luminaire has a ground conductor identified with green insulation or bare copper wire.
-
The luminaire is only suitable for a lamp with built- in safety or a low pressure lamp. An extra safety glass is not necessary.
-
The luminaire is equipped with a fuse. If the luminaire is out of order after the bulb has been replaced, the internal fuse has to be replaced.
If contact with the internal wiring can be made during this operation, this should be done by a competent electrician. -
The luminaire can be used with a dimming circuit. Consult a qualified electrician for choosing the right type (especially important for low voltage luminaires).
-
The Luminaire cannot be used with a dimming circuit.
-
The luminaire is dimmable with the supplied dimmer ONLY. Do not connect to an additional dimmer.
-
The dimmability features depend on the chosen lamp. More information on the dimmability features is available in the information pack provided with the bulb.
-
Luminaire with time and light setting options.
Minimum and maximum will be shown in the icon in part A. -
The luminaire can be placed at a maximum of 20ft height.
-
To reach an optimal working, you have to place the luminaire on the height mentioned in the icon. The maximum and minimum reach of the detector is also mentioned in the icon in part A.
-
The standard active range of vision of the detector covers the given degrees mentioned in the icon.
-
Ensure that you don’t drill through electrical wires or any other obstruction in the wall or ceiling during installation!
-
This luminaire contains in some places very hot parts.
-
Product to be installed by two people.
-
To avoid corrosion, clean the luminaire a minimum of 2 times per year with a soft cloth and a neutral detergent. (4 times in coastal or industrial areas).
-
The product is for indoor use only. Do not use in wet locations, areas directly exposed to water or outdoors.
-
The product is ZigBee certified. Zigbee is an open standard for indoor wireless communication. All Philips ZigBee Certified products can be connected with other Philips ZigBee Certified products.
-
Bluetooth• enabled product. The Bluetooth9 word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Signify is under license. Other trademarks and trade names are those of their respective owners.
Hue Personal Wireless Lighting is a trademark owned by Signify Holding B.V. Please go to www.philips-hue.com to learn more about Hue and how to use it.
This device complies with Part 15 of the FCC Rules and with RSS of Industry
Canada. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation. This equipment has been tested
and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
device generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions. may cause harmful interference to radio communications.
This Class B digital apparatus complies with CAN ICES-005. This digital apparatus does not exceed the class B limits for radio- noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
NOTICE: Changes or modifications made to this device not expressly approved by Signify North America Corporation (USA) and Signify Canada Ltd/Signify Canada uee. (Canada) (collectively “Signify”) may void the U.S.
FCC and Canadian authorization to operate this device, The advanced interface module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. However, there is no guarantee that interference will not occur in a particular installation If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/television technician for help.
Wireless Specification: Wireless RF mode frequency band: 2400-2483.5 MHz ·
Wireless communications protocol:
IEEE 802.15.4 • Operating channels Zigbee: channels 11- 26 • Operating
channels Bluetooth: channels 0-39
LIMITED WARRANTY
Signify warrants that this device’s hardware components will be free from
defects in material and workmanship for a period of two (2) years from the
date of purchase, unless a different period is stated in or on the packaging
of the product, based on up to 3 hours average working time per day/7 days per
week, when used as directed (the “Warranty Period”). Notwithstanding the
foregoing, the Warranty Period for all Energy Star-certified products is three
(3) years from the date of purchase. This limited warranty only applies to the
hardware components contained in the original packaging. This limited warranty
does not apply to any software, even if packaged or sold with the hardware
components. Signify does not warrant that use of this device will be
uninterrupted or error-free. If this device does not conform to this limited
warranty, Signify will send you, at its election, a replacement device or
refund your original price upon receipt of the returned device, register
receipt and proof of purchase. Please call our toll-free number,
1-800-555-0050, or write to us (address indicated on the packaging) to find
out how to return the device. This limited warranty does not cover devices
subject to accident,
neglect, abuse, misuse or acts of God.
REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS LIMITED WARRANTY LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSELY EXCLUDED. Some states and provinces do not allow exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state and province to province. This limited warranty is subject to, and may be superseded by, our End of Support policy to the extent Signify decides to terminate support for this device in accordance with its End of Support policy, available here: www.philips-hue.com/endofsupportpolicy
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. Alterations in design and technical specifications reserved.
CLEANING AND MAINTENANCE
Do not clean the device when it is on and connected to the power supply. To
avoid scratching the device, clean only with a soft dry cloth. Do not use
cleaning agents to clean the device. Manage in accordance with disposal laws
in your area.
‘Q’ Disposal of your old product: Manage in accordance with disposal laws in
your area. Remove the batteries A when you discard the product. Do not throw
the batteries away with normal household waste. They must be handed in at an
official collection point or at a Philips Dealer, both of which will dispose
of the batteries in an environmentally friendly way.
WIRELESS SPECIFICATIONS for all Philips Hue products: Wireless RF mode
frequency band: 2,400-2,483.5
MHz; Operating channels Zigbee if applicable: channels 11 – 26; Operating
channels Bluetooth if applicable :
channels 0-39; Maximum transmitted power <20 dBm
ENVIRONMENTAL SPECIFICATIONS for Hue Bulbs:
Temperature (operation): -4 … 113.F (-20 … 45 •C);
Temperature (storage): -13 … 140.F (-25 … 60 ·c);
Relative humidity: 5-95% non-condensing;
Standby power: <0.5W per lamp
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Signify is under license. Other trademarks and trade names are those of their respective owners.The product is ZigBee certified. Zigbee is an open standard for indoor wireless communication. All Philips ZigBee Certified products can be connected with other Philips ZigBee Certified products.Hue Personal Wireless Lighting is a trademark owned by Signify Holding B.V.Philips and the Philips shield emblem are registered trademarks of Koninklijke Philips N.V.
References
- Smart lighting | Philips Hue US
- End of Support Policy | Philips Hue US
- Energy consumption - calculate yours | Philips Hue
- Warranty | Philips Hue
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>