nordlux IPX4 blokhus-havelampe User Manual
- June 4, 2024
- nordlux
Table of Contents
nordlux IPX4 blokhus-havelampe
Mounting instruction
IP5X
IP5X: Dust is prevented from entering the lamp in amounts that can cause damage to the function/safety of the lamp.
IPX4
IPX4: Raindrops falling from any angle will not affect the function/safety of the lamp.
Class II: The lamp is double-insulated and does not need to be connected to the yellow/green earth wire.
MAX 60W
Do not exceed the maximum wattage.
Parallel arranging possible
The lamp is only suitable for connecting directly to the mains.
The mounting instruction must not be discarded.
Disposal of waste equipment by users in private households in the European Union. This symbol indicates that this product must not be disposed of with your other household waste. Electrical and electronic equipment contain substances that may cause damage to human health and the environment if not recycled correctly. It is your responsibility to hand over to a designated collection point for the recycling of waste electrical and electronic equipment. When handing over for correct recycling you help to prevent these products straining nature and the environment unnecessarily and to protect human health. For more information regarding correct disposal, please contact your local city office your household wast disposal service or the store where you purchased this product.
We congratulate you on your new outdoor lamp!
Guarantee
The Nordlux Outdoor lamps in copper, brass, tombac a and galvanized are
guaranteed for up to 15 years. This guarantee applies to extensive corrosion
in the form of holes in the metal caused by rust.
The guarantee is subject to the presentation of receipt.
There is not guarantee on the components which have been damaged by wear and
tear or mistreatment of the lamps.
Stainless steel
Remember to take care of your lamp. Just follow the guidelines below.
The shiny, uniform and decorative surface of stainless steel makes it very
suitable for outdoor use.
It is an alloy consisting of iron, chrome and nickel. During bath pickling, a
thin, rustproof oxide layer forms on the surface.
The surface is continually vulnerable to atmospheric conditions and from other
effects of the close environment. This means that the lamp must be regularly
maintained if its surface is to remain shiny and untarnished by rust.
Before setting it up, treat your lamp with acid-free oil, and dry it off with
a soft cloth. Repeat this three or four times a year.
Stainless steel lamps are not recommended for use in aggressive environments
such as coastal, agricultural or industrial areas.
Copper, Brass and Tombac fixtures
Our copper, brass and tombac fixtures are made from respectively solid copper,
brass and tombac. The mechanical machining will leave small scratches in the
surface, as well as residues of rinse aid. This rapidly disappears in the
patina process. After the first rain showers the copper/brass/tombak surface
will appear stained, but the aerated air and moisture will soon make the lamp
appear with dark brownish color. Over the years, the material copper will get
a beautiful patina-green color and brass/tombac will get a darker and more
uniform color. The uniformity of the patina surface, as well as the rate at
which the process occurs is dependent on the environment that affect the
fixture.
Hot-galvanized lamps
The zinc treatment of the steel lamps is executed manually in plants. The
temperature of the melted zinc is about 460 degrees. When the lamps are dipped
in melted zinc a reaction between the metalls occurs, which develops alloys in
the surface.
The lamp and the components of the lamp are manually dipped in the hot zinc.
This treatment leaves variations in the coating in the form of partly an
uneven surface and partly minor formations of drops.
Thin »zinc curtains« might also occur on the surface and they show as a thin
film which hangs down from the edge of the lamp. this film easily be removed
or brushed off with a soft brush.
Condensation
Condensation is a natural phenomenon arising under specific atmospheric
conditions. Damp heat and cold air meet, which causes condensation of water on
the surface.
When water heats up it leads to rising water vapor, which will be able to
affect electric components.
Condensation is not included by the Nordlux warranty unless it is possible to
prove that a technical /production error in the lighting causes entry of
water.
In case of condensation please check:
- If the lighting is mounted according to instructions. Washers should seal tightly. Make sure to tension screws and lenses.
- In the garden lightings rising damp from the ground may cause condense material into the metal post.
Aluminum fixtures
Our aluminum light fixtures are made from die-cast and/or extruded aluminum,
where the light fixture’s design determines whether both types of materials or
just one of them, are used for different parts of the same light fixture.
Aluminum light fixtures in raw aluminium are subsequently coated with a
special clear coat, which seals the surface to safeguard against corrosion.
Painted aluminium light fixtures are powder-coated and have a uniform and
smooth surface. To avoid the light fixture tarnishing, it is recommended to
clean and wipe the light fixture after mounting and repeat this process 3-4
times each year. This is done with a regular cleaning agent. Black light
fixtures which are bleached by strong sunlight can also benefit from treatment
with silicone spray as needed, to maintain the black color. Mounting light
fixtures in coastal, agricultural or industrial areas is not recommended, as
these aggressive surroundings may cause the light fixture to corrode, which
may entail spalling, bubbles in the surface and a whitish incrustation on the
light fixture’s surface.
- It is highly important that drainage holes are kept free of impurities if any.
BEFORE ASSEMBLING THE BOLLARD AGAIN DO REMEMBER TO WIPE OFF ALL PARTS!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>