FALL SAFE 50-7003 Inspector Personal Protection Equipment Instructions

50-7003 Inspector Personal Protection Equipment
Instruction Manual ****

GENERAL INSTRUCTIONS

Before using the Personal Protection Equipment (PPE) you must read carefully and understand the safety information described on general instruction and the specific  instructions.
ATTENTION!!! If you have any doubt about the product, if you need others language versions of the instructions for use, declarations of conformity or have any question  about the PPE, please contact us: www.fallsafe- online.com.
WARNING: The manufacturer and the seller decline any responsibility in case of incorrect use, improper application or modifications/reparations by persons not
authorized by FALL SAFE®.

PHYSICAL CONDITION AND TRAINING:

Work at height is potentially dangerous and it must only be performed by professionals and experienced persons. Before using the PPE you must be aware of: your mental  and physical condition; be trained for the use of the device; do not have any doubt about using the equipment and the field of application.
WARNING: the equipment shall only be used by a person trained and competent in its safe use.
WARNING: the consumption of alcohol, medicine or any other type of psychotropic will influence your balance, concentration conditional and must be avoided.

BEFORE USE:

For your safety it is strictly recommended that you always check your device and equipment before, during and after use and that you regularly submit your device and  equipment to inspections and controls by competent persons, every 12 months at least. These time intervals may change according to frequency and intensity of device and  equipment use. The FALL SAFE INSPECTOR® allows you to easily record and access information on inspections, inventory and use. It tracks equipment assignments by  worker or location and automates the inspection process. There are multiple system options available that allow for easy-access and time-saving information.
Every time before use, check (visually and tactile) the condition of the equipment components: textile material (straps, ropes, stitching) must not show any signs of abrasion,  fraying, burns, chemical or cuts. The metal material (buckles, karabiners, hooks, cable and metal rings) must not show any signs of wear, corrosion, deformation or defects  and should operate correctly.
WARNING: it is essential for safety that equipment is withdrawn from use immediately if:

1. Any doubt arise about its condition for safe use or;
2. It have been used to arrest a fall. It cannot be used again until confirmed in writing by a competent person that it is acceptable to do so;

For your safety read all contained information on this general instructions, as well as the specific instructions accompanying the device and make sure that you
understand them; ensure the equipment conditions and all recommendation of security; ensure that the components are compatible with each other and be sure
if are fulfilled with the rules, regulations and directives; ensure an emergency plan, check the work safety conditioning and confirm all system are assembled
correctly without interfering with each other.
WARNING: use of combinations of items of equipment in which the safe function on any one item is affected by or interferes with the safe function of another.
WARNING: a rescue plan shall be in place to deal with any emergencies that could arise during the work.
WARNING: Remind to check the limitation and the devices compatibility. Remember that the ropes have different particularities and can be changed according to the  weather conditions. The manufacture declines any responsibility for accidents, injuries or death due to improper and incorrect use by the user, all other usage procedures  must be considered forbidden. The equipment shall not be used outside its limitations, or for any purpose other than that for which it is intended.
WARNING: it is essential for safety to verify the free space required beneath the user at the workplace before each occasion of use, so that in the case of a fall, there will  be no collision with the ground or other obstacle in the fall path.
As the name suggests, the PPE is for personal use. In exceptional case using by a second user, carry out a check of the equipment before and after usage and
if possible take note of the relevant information.
WARNING: never use a PPE without knowing the provenance, or neither if the inspection records are not updated as it is issued.
All the materials and treatments used are antiallergenic; they should not cause skin irritations or sensitivity. The connectors are made of steel, zinc plated; light alloy,  polished or anodized: stainless steel, polished.
WARNING: during the use avoid the following hazards that may affect the performance of the equipment: extremes of temperature, trailing or looping of lanyards or  lifelines over sharp edges, chemical reagents, electrical conductivity, cutting, abrasion, climatic exposure and pendulum falls.

MARKING

WARNING: Never remove or damage the labels and marking; after use check if they are legible.
The following information is etched on the device: CE marking; (Number of the production process controlling body); Name of the manufacturer or of the person responsible for the product introduction on the market; standard (number and year of the standard; the logo that warns the user to carefully read the user instructions  attached to the product; production lot number; year of production; maximum load applicable in kN, the strength indicated is the lowest value guaranteed by the producer.  The marking on the device are indicated in different places depending on the dimension. See more detailed in “Specific Instructions”.
WARNING: Check the markings are legible even after use.
WARNING: it is essential for the safety of the user that if the product is re-sold outside the original country of destination the reseller shall provide instructions for use, for maintenance, for periodic examination and for repair in the language of the country in which the product is to be used.

LIFE TIME

It is rather difficult to establish the length of the device’s life, as it can be adversely affected by several negative factors such as intense, frequent or improper use; the  conditions the device is required to work in (humid, freezing and icy conditions); wear; corrosion; serious stress with or without relative deformation; exposure to heat  sources; improper storage; device age; exposure to chemical agents… (plus any further reason, not merely limited to all the foregoing reasons). Taking the adequate care of  your device (please consult the “Maintenance”) will have a considerable influence on and will definitely increase device durability and long life. By the way of example, the  following can be considered as a rule to determine standard potential durability of devices, tools and equipment: ten years for fall protection harness, fall protection  vests/jackets/ coveralls, accessories (lanyards, foot loop, suspension trauma and relief strap) anchor lines, anchor straps, ropes, carrying bags, fall arrest webbing blocks and  sharp edge tested; eight years for equipment conditioned to extreme environments (harness, lanyards, vests, jackets and coveralls); undefined for connectors, descenders, rope clamps, rope grabs, pulleys, anchor points; especially 10 years (5 in stock – 5 in use) for gloves and helmet . It is nevertheless recommended that you replace your devices,  tools and equipment at least every 10 years, considering that in the meantime new techniques or regulations may have become applicable and the equipment may no longer be compliant and/or compatible.
WARNING: The lifetime of an equipment can be limited in case of severe falls, extreme temperatures, contact with harmful chemicals, sharp edges and the absence of markings or labels.

ELIMINATION/ DISPOSAL CONSIDERATIONS
You should dispose of the equipment if: the lifetime has been exceed; if you suspect that the equipment is not safe; if it is obsolete (incompatible with modern equipment or  that do not conform to the standards updates); if it has been in a fall event (see the fall arrest indicator was violated); if it is over than 10 years.
The materials used in the equipment production may cause environmental impacts. For this purpose it is recommended that the equipment are disposed of in accordance  with the laws in force in the country where the disposal is taking place.
WARNING: The equipment which is not in operable condition or used in a fall event must be destroyed immediately.

REPARATION

ATTENTION!!! Any modification on the product void the guarantee and can compromise the user’s safety. The possibility of re-using the device must be authorizedexclusively by the producer with a prior written consent that reserves the right to carry out appropriated examinations and testing. Only the manufacture orauthorized staff can make the repairs and tampering.

MAINTENANCE, CLEANING AND INSPECTION

Check before, after and during use that the equipment works properly. If you need wash the components use clean water with a small amount of neutral soap to remove  persistent dirt or if the purpose is disinfect dissolve a disinfectant which contains quaternary ammonium salts in warm water (max. 20ºC), soak the equipment in this solution  for one hour. Rinse with potable water and leave them to dry out in the open air protected from sunlight. WARNING: when the equipment becomes wet, either from in use  or when due to cleaning, I shall be allowed t dry naturally, and shall be kept away from direct heat. If you need to lubricate the metal components you must use only silicone  based oil spray. WARNING: Remove the excess oil and check that if the lubrication don’t interferes the interaction between the device, others components of the system and  the user’s. Accordingly to the EN 365:2004 the PPE periodical examination should be carried out at least every 12 months by the manufacturer or a competent person  specifically authorized by the manufacturer. The frequency of inspection must vary depending on the intensity of usage, in order to ensure the durability of the product and  safety of the user. The inspection reports must be kept by the PPE owner. The result of the inspection must always accompany the product. If the report is missing or illegible, do not use the device. In case of doubt, the product should always be rejected. The FALL SAFE INSPECTOR® allows you to easily record and access information  on inspections, inventory and use. It tracks equipment assignments by worker or location and automates the inspection process. There are multiple system options available  that allow for easy-access and time- saving information. WARNING: for regular periodic examination, and that the safety of users depends upon the continued efficiently and  durability of the equipment. WARNNG: periodic examination are only to be conducted by a person competent for periodic examination and strictly in accordance with the manufacture´s periodic examination procedures.

STORAGE/ TRANSPORT

Remove the item from its container and store it in a cool, dry, well-aired place. There must not be any corrosive, solvent substances or heat sources (max. 80°C/ 176°F) in the storage place. The device must not come in contact with other sharp objects which can damage it. Never store the equipment before having thoroughly dried it and avoid  storing it in places with a high saline concentration. Except for the above-mentioned indications, there are no special precautions to be used during the transport. Avoid  leaving your equipment in a car or in a closed placed exposed to the sunlight.

GUARANTEE

The products are guaranteed for 12 months against any defects in material or manufacture. To analyse defects in materials and manufacture contact our after-sales service to  get the address to which should return the defective product in your country. Notes: Exclusions from the guarantee – incorrect wear, oxidation, leaking batteries in headlamps, modification/ alteration, poor storage, poor maintenance, damage due to accident or negligence, damage due use of product for which it is not designed. The manufacture  guarantee also does not apply if the serial number is no longer legible, any label has been removed from the product, if has been written on with a marker, covered by stickers  or using others tools for this purpose and if the annual inspection are not been realized.

According to the Regulation (EU) 2016/425
LISTED ORGANIZATION FOR: (EU) 2016/425 | ISO 9001:2015
SGS FIMOKO OY, P.O. Box 30 (Särkiniementie 3) 00211 Helsinki – Finland
NOTIFIED BODY: CE 0598
www.fallsafe-online.com
E-mail: support@fallsafe-online.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>