TOOLCRAFT 2526774 LED Magnifying Lamp with Third Hand User Manual
- June 9, 2024
- Toolcraft
Table of Contents
Operating Instructions
LED Magnifying Lamp with Third Hand
Item No. 2526774
Intended use
This product is a magnifying Lamp intended for detailed tasks, such as circuit
board soldering, small parts assembly, electronics repair, crafts, and more.
The product is designed with an LED lamp with magnifying glass (1.75X / 4X), 3
helping hands with alligator clips, soldering iron holder, soldering wire
spool holder, and 3 compartments on the metal base to hold the included
accessories or small items. The LED lamp is powered via the USB-C® port.
The product is intended for indoor use only. Do not use it outdoors. Contact
with moisture must be avoided under all circumstances.
If you use the product for purposes other than those described, the product
may be damaged.
Improper use can result in short circuits, fires, or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the
product.
Read the operating instructions carefully and store them in a safe place. Make
this product available to third parties only together with the operating
instructions.
All company names and product names are trademarks of their respective owners.
All rights reserved.
USB4® , USB Type-C® and USB-C® are registered trademarks of USB Implementers
Forum.
Delivery content
- Product
- Cleaning ball
- Sponge (30 x 50 mm)
- USB cable
- Operating instructions
Latest product information
Download the latest product information at www.conrad.com/downloads or scan the QR code shown. Follow the instructions on the website.
Description of symbols
The following symbols are on the product/appliance or are used in the text:
The symbol warns of hazards that can lead to personal injury.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/ guarantee.
5.1 General information
- The product is not a toy. Keep the product and accessories out of the reach of children and pets.
- Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
- If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel.
- Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.
5.2 Handling
- Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.
5.3 Operation
- WARNING! Risk of fire or injury. Do not place the magnifier in direct sunlight. Sunlight passing through or reflecting off the lens can cause a fire or burn injuries.
- WARNING! Risk of injury. Never use the magnifier to observe the sun or other strong light sources, such as lasers. This can cause permanent damage to the eyes.
- Do not place flammable objects in front of the lens.
- If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
– is visibly damaged,
– is no longer working properly,
– has been stored for extended periods in poor ambient conditions or
– has been subjected to any serious transport-related stresses.
5.4 Operating environment
- Do not place the product under any mechanical stress.
- Protect the product from extreme temperatures, strong jolts, flammable gases, steam and solvents.
- Protect the product from high humidity and moisture.
- Protect the product from direct sunlight.
5.5 LED light
Attention, LED light:
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
Product overview
- 1.75X Magnifying glass with LED lamp
- 4X Auxiliary lens
- Helping hands with alligator clips
- Rosin (not included)
- Cleaning sponge
- ON/OFF switch
- Metal base
- Cleaning ball
- Soldering iron holder
- USB-C ® input port
- Wire spool holder / Spool pin
Assembly
- To assemble the wire spool holder, use a screwdriver to loosen the screws of the 2 brackets on the back of the product, as shown (Fig. 1).
- Turn the 2 brackets until they point towards the back and are parallel with each other, and tighten the screws (Fig. 2).
- Insert the spool pin into your wire spool, then mount it on the 2 brackets (Fig. 3).
Operation
- Place the product on a flat, level, stable, and heat-resistant work surface.
- Connect a suitable USB power source to the USB-C® input port (5 V/DC, min. 1 A) on the product using the USB cable (included).
- Press the ON/OFF switch to turn the LED lamp on or off.
- After use, cover the lens with a soft cloth.
Cleaning and care
Important:
- Do not use harsh cleaning agents, rubbing alcohol or other chemical solutions. They damage the housing and can cause the product to malfunction.
- Do not immerse the product in water.
- To protect the lens from scratches, avoid touching the lens with fingernails or sharp objects.
- Remove loose particles with clean compressed air, then brush off any remaining debris with a soft, fine brush.
- Clean the magnifying glass with a soft, fibre-free cloth moistened with water or lens cleaning solution. Or clean the magnifying glass with a lens cleaning cloth.
- Clean the metal base and attachments with a soft, dry cloth. Moisten the cloth with water if required. Dry well.
- Store the product in a shaded, cool and dry place.
Disposal
This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be disposed of as unsorted municipal waste at the end of its service life. Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point. Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste. Conrad provides the following return options free of charge (more details on our website):
- in our Conrad offices
- at the Conrad collection points
- at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be
disposed of.
It should be noted that different obligations about the return or recycling of
WEEE may apply in countries outside of Germany.
Technical data
11.1 Power supply
Input USB-C® port ………………………………5 V/DC, min. 1 A
11.2 LED lamp
Power consumption ……………………………4 W
Light source ………………………………………40 LEDs
Luminous flux ……………………………………300 lm
Colour temperature …………………………….6500 K
Colour rendering index (CRI) ……………….≥80
11.3 Magnifying glass
Magnification (main / auxiliary lens) ………………………….1.75X / 4X
Main lens (Ø) …………………………………….100 mm
11.4 Environment
Operating/Storage conditions ………………-20 to +40 °C, <95 % RH (non condensing)
11.5 Dimensions
Base (L x W) ……………………………………..190 x 170 mm
Arm of magnifier (L) ……………………………265 mm
Arm of helping hand (L) ………………………250 mm
11.6 Weight
Product weight …………………………………..approx. 1.2 kg
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com). All rights including
translation reserved. Reproduction by any method, e.g. photocopy,
microfilming, or the capture in electronic data processing systems require the
prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2023 by Conrad Electronic SE.
*2526774_v1_0123_02_DS_m2L(1)http://www.conrad.com/downloads
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>