Mitel 700 DECT Phones User Manual
- June 9, 2024
- Mitel
Table of Contents
Mitel 700 DECT Phones
Safety Information (Mitel 700 DECT Phones, power supplies, and chargers)
Failure to observe this information can be hazardous and infringe existing
laws. Your device has been supplied with safety information and, where
applicable, with other device-specific information. You can download all user
documents available for this device (e.g. user guide) at
www.mitel.com. It is your responsibility to inform
yourself about the scope of functions, operation, and proper use of your
equipment
- Check whether you have all the user informa-tion available on your device, whether it conforms to your device’s version, and whether it is up to date.
- Always read the user documents first before you put your product into operation.
- Store the user information within easy reach and refer to it whenever uncertainties arise in connection with the use of the device.
- When handing over your device to others, make sure you enclose the relevant user information.
Medical equipment
Inform yourself if the use of radio equipment (cordless phones) is approved
near medical devices. Observe the alert messages and instruc-tions.
Availability of telephone connections
Do not rely on your cordless phone as your only means of communication in an
emergency or critical situations. Availability cannot always be guaranteed.
The device will be inoperable when main power of the communication system
fails.
Risk of explosion through sparking
On-premises subject to explosion hazards only use ATEX models specially
approved for that purpose.
Hands-free mode and Ringing tone
Do not hold the cordless phone up against your ear in hands-free operation and
during ringing tone, as the volume is then very high. The default setting for
ringing loudness meets regulatory requirements. It is recommended the default
setting is retained.
Mains Power
Use the original power supply only . Connect the power supply only to power
sources that conform to the indications on the power supply.
Maintenance
Make sure all installation and repair work is carried out by a specially
qualified technician. Do not touch the charging contacts with sharp, metallic,
and/or greasy objects. Always use a soft, moistened, or antistatic cloth to
clean your device. Do not use chemicals or other chemical products.
Cost control and Data protection
You should protect your device with a PIN so that no one can make phone calls
at your expense. A code will also protect your personal settings. When
carrying the cordless phone around, you should lock the keypad so it cannot be
accidentally activated.
Ambient conditions
Do not operate the device outside the temperature range of +5 °C to approx.
+40 °C. Avoid direct sunlight and other sources of heat. Protect your device
against the wet, excessive dust, corrosive liquids and steam. Do not expose
your device to electromagnetic fields (electric motors, household appliances).
The speech quality could be affected. To prevent interference, avoid placing
your handset in the immediate vicinity of computers, radios, TV sets, VCRs,
and other telephone sets.
Disposal
Be sure to dispose of your device, batteries and packaging in an
environmentally compatible way. Electrical equipment does not belong in
domestic waste. Deposit it at a return center.
Accessories
Use original accessories or specifically approved accessories only. The use of
other accessories may decrease performance or pose a risk to your health or
safety.
Purpose and function
This product is part of a Mitel communication solution. In GAP mode the
device can also be operated on systems by other manufacturers, provided they
support the GAP standard. Any other use does not comply with the intended
purpose and is not permitted.
Important Safety Information
Communications Regulation InformationFCC Notices (U.S. Only)
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
-
This device may not cause harmful interference
-
this device must accept any interference received, including interference that may cause undesired operation. Modifications not expressly approved by this company could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equip- ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.
- Increase the separation between the equip-ment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Health and Safety Information
Exposure to Radio Frequency (RF) Signals:
The wireless phone is a radio transmitter and receiver. It is designed and
manufactured not to exceed the emission limits for exposure to radio frequency
(RF) energy set by the Federal Communications Commission (FCC) of the U.S.
Government. These limits are part of comprehensive guidelines and establish
permitted levels of RF energy for the general population. The guidelines are
based on the safety standards previously set by both U.S. and international
standards bodies. These standards include a substantial safety margin designed
to assure the safety of all persons, regardless of age and health. This device
and its antenna must not be co-located or operating in conjunction with any
other antenna or transmitter.
This EUT has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1-1992 and had been tested in accordance with the measurement procedures specified in FCC/OET Bulletin 65 Supplement C (2001) and IEEE 1528-2003.
Industry Canada (Canada only)
Operation of this device is subject to the following two conditions:
- this device may not cause interference
- this device must accept any interference, including interference that may cause undesired operation of the device.
Exposure to Radio Frequency (RF) Signals:
The wireless phone is a radio transmitter and receiver. It is designed and
manufactured not to exceed the emission limit for exposure to radio frequency
(RF) energy set by the Ministry of Health (Canada), Safety Code 6. These
limits are part of comprehensive guidelines and establish permitted levels of
RF energy for the general population. These guidelines are based on the safety
standards previously set by international standard bodies. These standards
include a substantial safety margin designed to assure the safety of all
persons, regardless of age and health.
This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment / general public exposure limits specific in ANSI/IEEE C95.1-1992 and had been tested in accordance with the measure-ment procedures specified in IEEE 1528-2003.
Limited Warranty (Australia only)
The benefits under the Mitel Limited Warranty below are in addition to other
rights and remedies to which you may be entitled under a law in relation to
the products.
In addition to all rights and remedies to which you may be entitled under the Competition and Consumer Act 2010 (Commonwealth) and any other relevant legislation, Mitel warrants this product against defects and malfunctions in accordance with Mitel’s authorized, written functional specification relating to such products during a one (1) year period from the date of original purchase (“Warranty Period”). If there is a defect or malfunc-tion, Mitel shall, at its option, and as the exclusive remedy under this limited warranty, either repair or replace the product at no charge, if returned within the warranty period.
Repair Notice
To the extent that the product contains user-generated data, you should be
aware that repair of the goods may result in loss of the data. Goods presented
for repair may be replaced by refurbished goods of the same type rather than
being repaired. Refurbished parts may be used to repair the goods. If it is
necessary to replace the product under this limited warranty, it may be
replaced with a refurbished product of the same design and color.
If it should become necessary to repair or replace a defective or malfunctioning product under this warranty, the provisions of this warranty shall apply to the repaired or replaced product until the expiration of ninety (90) days from the date of pick up, or the date of shipment to you, of the repaired or replacement product, or until the end of the original warranty period, whichever is later. Proof of the original purchase date is to be provided with all products returned for warranty repairs.
Exclusions
Mitel does not warrant its products to be compat-ible with the equipment of
any particular telephone company. This warranty does not extend to damage to
products resulting from improper installation or operation, alteration,
accident, neglect, abuse, misuse, fire, or natural causes such as storms or
floods after the product is in your possession. Mitel will not accept
liability for any damages and/or long-distance charges, which result from
unauthorized and/or unlawful use.
To the extent permitted by law, Mitel shall not be liable for any incidental damages, including, but not limited to, loss, damage, or expense directly or indirectly arising from your use of or inability to use this product, either separately or in combination with other equipment. This paragraph, however, is not intended to have the effect of excluding, restricting or modifying the application of all or any of the provisions of Part 5-4 of Schedule 2 to the Competition and Consumer Act 2010 (the ACL), the exercise of a right conferred by such a provision or any liability of Mitel in relation to a failure to comply with a guarantee that applies under Division 1 of Part 3-2 of the ACL to a supply of goods or services.
This express warranty sets forth the entire liability and obligations of Mitel with respect to a breach of this express warranty and is in lieu of all other express or implied warranties other than those conferred by a law whose application cannot be excluded, restricted, or modified. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Warranty Repair Services
Procedure: Should the product fail during the warranty period and you wish to make a claim under this express warranty, please contact the Mitel authorized reseller who sold you this product (details as per the invoice) and present proof of purchase. You will be responsible for shipping charges, if any. Limitation of liability for products not of a kind ordinarily acquired for personal, domestic, or household use or consumption (eg goods/services ordinarily supplied for business use).
- To the extent permitted by law and subject to clause
- below, the liability of Mitel to you for any non-compliance with a statutory guarantee or loss or damage arising out of or in connection with the supply of goods or services (whether for tort (including negligence), statute, custom, law or on any other basis) is limited to:
- in the case of services:
- the resupply of the services; or
- the payment of the cost of resupply;and
- in the case of goods:
-
1. the replacement of the goods or the supply of equivalent goods; or - the repair of the goods; or
- the payment of the cost of replacing the goods or of acquiring equivalent goods; or
- the payment of the cost of having the goods repaired.
- Clause 1.1 is not intended to have the effect of excluding, restricting, or modifying:
- the application of all or any of the provisions of Part 5-4 of Schedule 2 to the Competition and Consumer Act 2010 (the ACL); or
- the exercise of a right conferred by such a provision; or
- any liability of Mitel in relation to a failure to comply with a guarantee that applies under Division 1 of Part 3-2 of the ACL to a supply of goods or services.
After Warranty Service
Mitel offers ongoing repair and support for this product. If you are not
otherwise entitled to a remedy for a failure to comply with a guarantee that
cannot be excluded under the Australian Consumer Law, this service provides
repair or re-placement of your Mitel product, at Mitel’s option, for a fixed
charge. You are responsible for all ship-ping charges. For further information
and ship-ping instructions contact:
Manufacturer:
- Mitel South Pacific Pty Ltd (“Mitel”) 6/32 Walker Street
- North Sydney, NSW2060, Australia Phone: +61 2 9023 9500
Note:
Repairs to this product may be made only by the manufacturer and its
authorized agents, or by others who are legally authorized. The unauthorized
repair will void this express war ranty.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>