MIKSTER WSTHD-800-01-DS Radio Temperature and Humidity Sensor Owner’s Manual
- June 10, 2024
- MIKSTER
Table of Contents
WSTHD-800-01-DS Radio Temperature and Humidity Sensor
Product Information
The WSTHD-800-01-DS is a radio temperature and humidity sensor that measures
the temperature and humidity in a given area. The device has a measuring range
of -40oC to 85oC for temperature and 0% to 100% for humidity. It has an
accuracy of 0.1oC for temperature measurement and a resolution of humidity
measurement.
The device is powered by a 3.6V lithium battery that has a battery life of not
less than 2 years. It has an operating frequency of 868.4 MHz and an internal
measuring buffer of 136 hours recording every 1 minute. The device has a
degree of protection of IP65, polycarbonate and is EMC compliant.
Product Usage Instructions
To use the WSTHD-800-01-DS radio temperature and humidity sensor, follow the steps below:
- Install the device by mounting it on a wall or any other surface in the desired location.
- Ensure that the device is within the operating conditions for the housing sensor, which is a temperature range of -30oC to 85oC and humidity range of 0% to 75%.
- Turn on the device by inserting the 3.6V lithium battery.
- Wait for the device to start recording data, which can be up to 136 hours recording every 1 minute.
- To access the recorded data, connect to the device using the operating frequency of 868.4 MHz.
- If necessary, replace the battery after not less than 2 years of use.
For further information or assistance, please refer to the product manual or contact MIKSTER Sp. z o.o. at info@mikster.pl.
WSTHD-800-01-DS Radio temperature and humidity sensor
DESCRIPTION
A radio temperature and humidity sensor is a measurement module, the reading
of which is possible through a radio connection. Its use is recommended in
places where creating a wired installation is difficult or inadvisable. The
sensor enables a continuous registration of temperature and humidity up to 136
hours
with a frequency of registration every 1 minute. The sensor’s registration can
be read by a radio recording unit connected to a computer with LOGGISOFT
software installed. Built-in LCD display facilitates operating the device and
enables local visualization of the measurements.
Sensor dimensions WSTHD-800-01-DS:
Technical data
Measuring range of the probe temperature| – 40oC..85 oC
Accuracy of the probe measurement for the temperature range| ±0,5 oC (-20°C ..
+85°C)
±2 oC (-40°C .. -20°C)
Measurement resolution temperature| 0,1 oC
Probe measuring range humidity| 0..100% (-30oC..85 oC)
Accuracy of humidity measurement| ±3% RH (in the range 15..85%)
±3..5% RH (in the remaining range)
Resolution of humidity measurement| 1,0%
Power| Lithium battery 3.6V
Battery life| Not less than 2 years
Operating conditions for the housing sensor| -30°C .. +85°C
Humidity: 0..75%
Storage conditions| Temperature: -30oC..85 oC Humidity: 0..75%
Electromagnetic compatibility (EMC)| Immunity acc. to PN-EN61000-6-2
Data transmission| Operating frequency 868.4 MHz
Internal measuring buffer| 136 hours (recording every 1 minute)
Installation data
External dimensions| Housing: 82x80x60mm (W/HD) with antenna and temperature
sensor 82x234x60mm
Weight| 210g
Dimensions of temperature and humidity probe| Długość 48mm, średnica ø19,5mm
Length 48mm, diameter ø19.5mm Length 75mm*, diameter ø19.5mm
Mounting| 4 holes ø4,2mm spacing 70mm
heigh*tS5o0nmd mna przewodzie o długości 2,5m
Degree of protection, housing| IP65, polycarbonate
Website: www.mikster.com.pl
Address: MIKSTER Sp. z o.o. 41-250 Czeladź, ul. Wojkowicka 21, tel. 32
763 77 77
Fax: 32 763 75 94
Email: info@mikster.pl