KUFATEC 39703 FISTUNE DAB+ interface Instruction Manual
- June 3, 2024
- KUFATEC
Table of Contents
39703 FISTUNE DAB+ interface
Instruction Manual
Version 1.03
(12.10.2021)
Installation instruction FISTUNE DAB / DAB+
Audi MMI 3G / 3G+
Article no. 39703
www.kufatec.de
Kufatec GmbH & Co. KG
Dahlienstr. 15
23795 Bad Segeberg
e-mail: info@kufatec.de
Disclaimer
Dear Buyer,
our cable harnesses are developed with the help of the circuit diagrams and
wiring schemes of the particular vehicle producer and they are tested and
adjusted to the original vehicle before the serial production. Therefore the
integration into to the on-board electric and electronic system follows the
information of the vehicle producers.
Our installation instructions are consistent, in course of the necessary pre-
understanding and the precision of the presentation in text and picture, with
the staff usual in vehicle electrics / electronic and they have proven their
value already hundredfold in practice.
If during the installation of our products drench occur difficulties, so we
are any time ready to provide you support by phone or E-Mail. Additionally we
offer you to use the installation in our workshop in Bad Segeberg.
The costs arising from the third parties assigned with the installation of our
products, bears the Buyer. Only when it proves that there is a failure of our
product we will compensate the evidenced costs of the assembly and the costs
of the dismantling of the defective product, whereby we limit the cost
reimbursement up to 110 EURO gross and we reserve our right to check the
claimed defect in our workshop in Bad Segeberg. The costs of dispatch will be
refunded in case of a justified claim.
We made the experience that each professional workshop which is equipped with
a necessary diagnosis devices, diagnosis software and the circuit diagrams of
the producer, can find the possible defects in our products within a short
period of time, so the assembly and disassembly including failure diagnosis,
can take place in maximum 60 minutes.
We also made the experience that many workshops are not able to cope with the
producer’s circuit diagrams and cannot read the common wiring schemes, so for
simplest installation labors several hours are calculated. You will understand
that we neither take the risk to find a reliable workshop nor we finance the
training for the workers of the workshop of your confidence.
The costs that arise from the acquisition of the missing parts or replace for
defective parts from another suppliers, we reimburse to the amount of the
costs which would have arisen in case of subsequent delivery (saved
expenditure). In this case according to the legal warranty law there would be
no reimbursement right of any kind, as long as no deadline was set for the
supplementary performance or a deadline for supplementary performance has not
expired.
So if you have any problems during the installation or operation of our
products call us write us an EMail, send us the product or come to our
workshop in Bad Segeberg with your vehicle. We are sure to find a solution for
concern of every kind.
Kind regards
Your Kufatec GmbH & Co. KG Team
Copyright
Our assembly and operation manuals, assembling diagrams and additional
documentation in text or picture form are protected by law. Disclosure and
distribution of this documentation through print or online media is permitted
only after previous written acceptance from Kufatec GmbH & Co. KG.
General advice
While developing this product, your personal safety combined with the best
operating service, modern design and an up-to-date production technique was
especially taken into account.
Unfortunately, despite the utmost care injuries and/or damages might occur due
to improper installation and/or use.
Therefore please read with great care and completely this operating manual and
store it appropriately!
For your safety all our products pass through a 100% control check.
We reserve the right to carry out technical changes which serve the
improvement at any time. According to each article and purpose, it is
sometimes necessary to check each country’s legal regulations before
installing and starting the unit. In case of guarantee claims, the device has
to be sent back to the seller in the original packaging with the attached bill
of purchase and detailed defects description. Please pay attention to the manufacturers return requirements (RMA). The legal warranty directions are
valid. The warranty claims as well as the operating permissions become invalid
due to:
a) unauthorized changes to the device or accessories which have not been
approved or carried out by the manufacturer or its partners
b) opening the device`s frame
c) self-made repairs on the device
d) improper use / operation
e) brute force to the device (drop, willful damage, accident etc.)
During installation, please pay attention to all safety relevant and legal
directions.
The device has only to be installed by trained personnel or similarly
qualified people.
Please limit the failure search to ca. 0,5 hour for the mechanical resp. 1.0
hour for electric labors during the assembly or functioning problems.
To avoid unnecessary additional expenses please send immediately an inquiry to
our technical support using the Kufatec form
(http://www.kufatec.de/shop/de/infocenter/).
Please provide always the following information: chassis number part number of
the add-on kit exact description of the problem already executed labor
Safety instructions
The installation can be executed only by trained qualified personnel. Before the installation disconnect the power supply. Therefore cut off the battery from the vehicle electric system, follow the manufacturer’s specification.
- Never use bolts, screws and other fastening elements from car’s safety devices or steering wheel, brakes because it may influence your driving safety and cause accidents.
- Connect the device only to a 12V vehicle voltage with chassis ground to the car body. This unit cannot be used in large trucks or other vehicles which use a DC 24 V battery wiring system voltage.
- Avoid to install the device in places where it could hinder the safe driving or functional efficiency of the other units installed in the vehicle.
- This unit is only for the use with the following vehicles and model line; Only connections described within this instruction manual are allowed or required to use for installation.
- For damage impact caused by faulty installation, unsuitable connections or assembling in inappropriate vehicle types or models Kufatec GmbH &Co.KG assumes no liability.
- We advise you that these units process data out of the MOST protocol from the vehicle. During the assembly of this unit we as supplier have access to a specific model and we as producer don’t know the overall system you work with.
- Especially in case of changes within the same model line and the same model year we don’t guarantee the usability of our products. In case of the usability of our products with the manufacturer’s changes Kufatec GmbH assumes no liability.
- Kufatec GmbH assumes no liability that the assembly of the unit described in this manual is approved according the warranty regulations of the single car manufacturers. Please check your manufacturer’s conditions and warranty before you begin the installation.
- Kufatec GmbH reserves the right to change the device specification without further notice.
- Errors and changes excepted.
References of legal regulations for operation
Use this unit in the intended domain only. If you use the unit in a foreign
domain, if the unit is not installed properly, or if the unit will be
reconstructed the operating permit and warranty will expire.
NOTE: Not applicable for vehicles with an original DAB-reception
(combined radio box with DAB and FM/AM/MW as well).
NOTE CHANNEL SEARCH:
There is no automatic channel search, it has to be done manually through MMI.
A new manual channel search is necessary only for regional ensembles, when the
vehicle changes the position and in this way the regional ensemble are altered
too. In case of national ensembles a new channel search is not necessary.
NOTE ANTENNA MODULE:
Depending on the vehicle type you need a different antenna module. This one
has to be ordered separately.
Following you will find a list of the modules:
- A6 4G Limo (article no.: 39528)
- A6 4G Avant (article no.: 39528-1
- A7 4G (article no.: 39529)
- A8 4H (article no.: 39530)
- A4 8K Limo 3G (article no.: 39531-1)
- A4 8K Avant (article no.: 39531-4)
- A5 8T 3G (article no.: 39532-1, 39532-3)
- A5 8T Sportback (article no.: 39532-4)
- A5 8F Cabrio (article no.: 39532-6)
- A6 4F Avant (article no.: 39533-2, 39533-3)
- A8 4E 3G (article no.: 39534-1, 39534-3)
Scope of delivery for 39703
FISTUNE Interface Cable harness
Installation instructions
The following presentation shows the laying of the wires and the position of the single components as well.
- (Radio box) FISTUNE Interface A4 / A5, A6 4F, A6-A7 4G. A8 4E, Q3, Q5
- (Radio box) FISTUNE Interface A8 4H
- (Radio box) FISTUNE Interface Q7 4L
NOTE: Place the FISTUNE on a proper spot at the radio box. Consider the
firm and safe seat of the box.
Radio box Audi A4 8K, A5 8T, A6 4F, Q5 MMI 3G
Loosen the screws of the lashing eyes and the screws behind the lever for the
backrest (fig.1). The hook (fig.2) has to be bent up first and then removed.
Loosen the bolt situated behind. The radio box is situated behind the left
trunk lining (fig. 3).
Radio box Audi Q7 4L MMI 3G
Loosen the screws of the lashing eyes. Remove the cover on the right-hand
side. The radio box is situated behind the right trunk lining (fig. 5).
Radio box Audi A8 4H
Loosen the screws of the lashing eyes. Remove the right and left trunk lining.
Take out the covering of the rear bench seat (fig. 8).
Loosen the screws of the holder of the comfort control unit and remove (fig. 9, 10). The radio box is situated directly behind (fig. 11).
Radio box Audi A6 4G, A7 4G
Loosen the screws of the lashing eyes. Remove the left trunk lining. The radio
box is situated in the bottom area of the control units holder.
Radio box Audi Q3
Open the maintenance door by turning the rotary handle by 90 degrees.
Disconnect any plug connections and remove the maintenance door. The radio box
is mounted behind the side covering in the trunk on the driver`s side.
Interface connection MMI 3G/ MMI 3G+
Light conductor
The connection takes place through Plug & Play on the back side of the radio
box. Remove the original light conductor plugs from the radio box (fig. 14).
Connect the original light conductor plug with the socket of the delivered
cable harness (fig. 15).
Integrate the light conductor of the delivered cable harness in the radio box (fig. 16). The figure 17 shows the correct connection of the interface.
Connect the 18-pin plug and the light conductor plug to the interface (fig. 18).
Antenna
Connect the antenna plug to the unit.
Power supply
The connection of the power supply takes place with the Quadlock-plug of the
radio box.
The wires Brown (ground) and Red (permanent positive) have to be connected by
means of a braze or a new crimp joint specifically to the vehicle (fig. 19,
20).
BROWN – PIN17
RED – PIN 18
CAUTION: Do not use press-on connectors!
NOTE: The wire color can also be neutral (gray). If this is the case,
then please consider the wire imprint.
After the connection please carry out sufficient functioning tests. When the tests are successful then as next assemble everything in the backward sequence.
Operation
Because the FISTUNE is completely integrated in the vehicle, therefore the operation of the digital radio reception takes place through your MMI. The operation is detailed explained in the user guide of your vehicle.
Coding
The coding of the vehicle is after the assembly of FISTUNE not necessary. But
you can add the module to the installation list under the address 19.
In order to execute the coding of the vehicle please contact your VW Audi
partner.
Now include the encoding “0F” in the installation list.
NOTE: After the first installation press the soft key “Manually” in the
MMI and start the search.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>