Mikster NTHD-01 PHARM Radio Temperature and Humidity Sensor Owner’s Manual
- June 10, 2024
- MIKSTER
Table of Contents
Mikster NTHD-01 PHARM Radio Temperature and Humidity Sensor
Product Description
- Dimensions: External one, height 90 mm
- Power: 3.6 v AA 2.6 AA replaceable lithium battery
- Antenna: A permanently mounted external one
- Registration: 4,608 samples/channel
- Display: LCD 4 digits dedicated
- Temperature measuring range: 0°C to 50°C
- Temperature measurement error: ±1°C
- Temperature measuring resolution: 0.1°C
- Humidity measuring range: 0%RH to 100% RH
- Humidity measuring error: ±1% RH
- Humidity measuring resolution: 0.1% RH
- Communication: 868.4 MHz radio
- Measuring element: NTC thermistor and capacitive sensor
- Measurement channels: Temperature and humidity
- Operating conditions: -20°C to 50°C, 0%RH to 100%RH
- External dimensions weight: 80 g (net)
- Fixing: You can hang it or put it on the ground
- Degree of protection: IP 20
Product Usage Instructions
- Insert the AA lithium battery into the sensor
- Place the sensor in the desired location (hang it or place it on the ground)
- The LCD display will show the current temperature and humidity readings
- The sensor will automatically transmit temperature and humidity data to a receiving device at a frequency of 868.4 MHz radio
- If an additional probe is required, connect it to the sensor following the instructions provided in the user manual
- Keep the sensor operating within the recommended operating conditions of -20°C to 50°C, 0%RH to 100%RH
- If the battery needs replacing, follow the instructions provided in the user manual and replace it with a 3.6 v AA 2.6 AA replaceable lithium battery
For any further information or assistance, please contact MIKSTER Sp. z o.o. at tel. 32 763 77 77 or email info@mikster.pl.
DESCRIPTION
NTHD-01 PHARM sensor enables continuous recording of temperature for up to 136
hours with a recording frequency every 1 minute. The sensor’s registration can
be read via the NRU-20 PHARM+ radio logger connected to a computer with
installed software
Loggisoft” software. The built-in LCD display makes the device easy to operate
device and enables local 1isualization of the measurements. Its use to
recommended in places where installation is difficult or inadvisable, and
there are no difficult environmental conditions (high humidity/dust) e.g. in
pharmacies, clinics, hospitals.
Technical data
Technical data
Power| 3.6 v AA 2.6 AA replaceable lithium battery
Antenna| permanently mounted external one,
height 90 mm
Registration:| 4,608 samples/channel
Display:| LCD 4 digits dedicated
Temperature measuring range:| -30 ℃ ÷ 70 ℃
Temperature measurement error:| ≤±0.3 ℃ in the range of 0 ℃ to 25
℃
≤±0.5 ℃ in other ranges
Temperature measuring resolution:| 0,1℃
Humidity measuring range:| 0%RH to 100% RH
Humidity measuring error:| ≤ ±3% RH w zakresie 0% ÷ 80%RH
≤ ±5% RH w zakresie 80% ÷ 100%RH
Humidity measuring resolution:| 1% RH
Communication:| 868.4 MHz radio
Measuring element:| internal digital sensor
option to connect a dedicated, external temperature or temperature and
humidity probe (sold separately)
Measurement channels:| two internal (temperature and humidity) Expandable by a further 2
using an external probe
Operating conditions:| temperature: –30°C to 70 °C humidity: 0% RH to 99% RH
(no condensation)
Installation data
External dimensions| 71 x 71 x 27 mm (w x h x d) without antenna
Weight| 80 g (net)
Fixing| You can hang it or put in on the ground
Degree of protection| IP 20
Dimensions
Connecting an additional probe
www.mikster.com.pl
MIKSTER Sp. z o.o. 41-250 Czeladź, ul. Wojkowicka 21, tel. 32 763 77 77
fax : 32 763 75 94 email: info@mikster.pl