ADA INSTRUMENTS COSMO MICRO 25 Laser Distance Meter User Manual
- June 4, 2024
- ADA INSTRUMENTS
Table of Contents
- CHARACTERISTICS
- FEATURES (PIC.1)
- DISPLAY (РIC. 2)
- BATTERY CHARGE
- MEASUREMENT UNIT (FT/M)
- MEASUREMENTS
- CONTINUOUS MEASUREMENT
- OPERATION WITH MOBILE APP
- CALIBRATION ADJUSTMENT
- SAFETY INSTRUCTIONS
- WARRANTY
- PRODUCT LIFE
- WARRANTY CARD
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
OPERATING MANUAL
COSMO MICRO 25
Laser distance meter
CHARACTERISTICS
Working range, m …………………………………………0.05~25
Accuracy, mm………………………………………………..±3
The minimum unit of measurement, m………………1
Measurement unit ……………………………………….m/ft
Laser class …………………………………………………….класс 2
Laser type ……………………………………………………620~690nm; <1mV
Automatic switch-off, sec …………………………..180
Battery/charger connector …………………………built-in Li-ion battery / USB Type-С 5V
Operating temperature, С °……………………………0~40
Storage temperature, С °…………………………….. -20~60
Dimensions, mm…………………………………………….84×39×19
Weight, g …………………………………………………………50.5
FEATURES (PIC.1)
- On/measuring/continuous measurement
- Сlear/Off
- Display
- Power connector USB Type-С
- Receiving lense
- Laser window
DISPLAY (РIC. 2)
- The reference point (the bottom edge only)
- Laser is On
- Battery power
- Measurement unit (m/ft)
- Line 2
- Line 1
- Mainline
BATTERY CHARGE
Laser distance meter works from the built-in Li-On battery. Battery power is
shown on the display (3). Blinking power indicator (3) without inner bars
shows low battery level. To charge, connect the charger via USB Type-C wire to
the connector on the bottom part of the tool. When fully charged, indicator
(3) does not blink, all segments are filled.
ATTENTION! Do not use a charger with an output voltage higher than 5V.
Higher voltage will damage the device.
ON / OFF
- Press button (1) once: the device and laser are switched On.
- Long pressing the button activates the continuous measuring.
- To switch Off the tool press and hold button (2) within 2 sec.
MEASUREMENT UNIT (FT/M)
Switch Off the tool. Press and hold button (1) for more than 8 sec until you hear a beep sound. Selected measurement units (ft/m) will be shown on the display. Next time when switching on the tool, if you do not plan to change measurement units, do not press button ON for more than 8 sec.
MEASUREMENTS
Press button (1) once to switch On the tool and activate laser. Press the button once again to make measurements. A beep will sound. The result of the measurement will be shown in the main stroke. At the next measurement, the result will be displayed in the main stroke, and the previous result will move to stroke 1. To erase the result, press button (2).
CONTINUOUS MEASUREMENT
In continuous measurement mode, the tool continuously measures distances. To activate this mode, press and hold the button (1) for more than 2 seconds. The display will show the measured distance in the main stroke, the minimum measured distance in stroke 1 and the maximum measured distance in stroke 2. To turn off the continuous measurement, press button (1).
OPERATION WITH MOBILE APP
Measured distances can be transferred to a mobile device. To get started, install the ADA PHOTO PLAN software by scanning the QR code on the package, or search online app stores. In the application, you can take photos of measured objects or drawings. On the lines indicating the dimensions, you can apply the values obtained from the device.
CALIBRATION ADJUSTMENT
Measurement accuracy can be calibrated by the user. The calibration step is 1
mm. Make a control measurement of the distance. Calculate the correction to be
entered into the memory of the tool using the formula (in mm):
True value – received value = correction. (e.g.: 200 mm – 202 mm = -2 mm).
How to make a correction:
- Switch OFF the tool.
- Press and hold the button (OFF) for more than 10 sec until you hear a beep. The display will show the correction value entered at the factory.
- To calculate a new correction value, it is necessary to add the calculated correction with its own sign.(f.e.: 13 mm + (-2mm) = 11 mm).
- Press the button Switch ON (increase) or Switch OFF (decrease) to set a new calibration value.
- To save a new value and exit calibration mode, press and hold the Switch ON button when you hear a beep signal.
- Switch OFF the tool.
SAFETY INSTRUCTIONS
Prohibited:
- Use a charger with an output voltage higher than 5V to charge the battery of the tool;
- Use the tool outside of the instructions and use beyond the permitted operations;
- Use the device in an explosive environment (gas station, gas equipment, chemical production, etc.);
- Disabling the tool and removing the warning and indicative labels from the tool;
- Opening the tool with tools (screwdrivers, etc.), changing the design of the tool or modifying it;
- Intentional blinding of third parties by the laser, direct aiming of the device at the sun; • Look at the laser beam.
WARRANTY
This product is warranted by the manufacturer to the original purchaser to be free from defects in material and workmanship under normal use for a period of two (2) years from the date of purchase. During the warranty period, and upon proof of purchase, the product will be repaired or replaced (with the same or similar model at the manufacturer’s option), without charge for either part of labor. In case of a defect please contact the dealer where you originally purchased this product. The warranty will not apply to this product if it has been misused, abused or altered. Without limiting the foregoing, leakage of the battery, and bending or dropping the unit are presumed to be defects resulting from misuse or abuse.
PRODUCT LIFE
The product life of the tool is 3 years. The battery and the tool should never be placed in municipal waste.
EXCEPTIONS FROM RESPONSIBILITY
The user of this product is expected to follow the instructions given in the
operators’ manual. Although all instruments left our warehouse in perfect
condition and adjustment the user is expected to carry out periodic checks of
the product’s accuracy and general performance.
The manufacturer, or its representatives, assumes no responsibility of the
results of faulty or intentional usage or misuse including any direct,
indirect, consequential damage, and loss of profits. The manufacturer, or its
representatives, assumes no responsibility for consequential damage, and loss
of profits by any disaster (earthquake, storm, flood …), fire, accident, or an
act of a third party and/or usage in other than usual conditions.
The manufacturer, or its representatives, assumes no responsibility for any
damage, and loss of profits due to a change of data, loss of data and
interruption of business, etc., caused by using the product or an unusable
product. The manufacturer, or its representatives, assumes no responsibility
for any damage, and loss of profits caused by usage other than explained in
the users’ manual.
The manufacturer, or its representatives, assumes no responsibility for damage
caused by wrong movement or action due to connecting with other products.
WARRANTY DOESN’T EXTEND TO THE FOLLOWING CASES:
- If the standard or serial product number will be changed, erased, removed or wil be unreadable.
- Periodic maintenance, repair or changing parts as a result of their normal runout.
- All adaptations and modifications with the purpose of improvement and expansion of the normal sphere of product application, mentioned in the service instruction, without the tentative written agreement of the expert provider.
- Service by anyone other than an authorized service center.
- Damage to products or parts caused by misuse, including, without limitation, misapplication or negligence of the terms of service instruction.
- Power supply units, chargers, accessories, wearing parts.
- Products, damaged from mishandling, faulty adjustment, maintenance with low-quality and non-standard materials, presence of any liquids and foreign objects inside the product.
- Acts of God and/or actions of third persons.
- In case of unwarranted repair till the end of the warranty period because of damages during the operation of the product, it’s a transportation and storing, the warranty doesn’t resume.
WARRANTY CARD
Name and model of the product ____
Serial number
Date of sale
Name of commercial organization ____
Stamp of commercial organization.
Warranty period for the instrument exploitation is 24 months after the date of
original retail purchase.
During this warranty period, the owner of the product has the right for free
repair of his instrument in case of manufacturing defects.
Warranty is valid only with original warranty card, fully and clear filled
(stamp or mark of the seller is obligatory).
Technical examination of instruments for fault identification which is under
the warranty is made only in the authorized service center.
In no event shall the manufacturer be liable before the client for direct or
consequential damages, loss of profit, or any other damage which occur in a
result of the instrument outage.
The product is received in the state of operability, without any visible
damages, in full completeness. It is tested in my presence. I have no
complaints to the product quality. I am familiar with the conditions of
warranty service and I agree.
Purchaser signature_____
Before operating you should read service instructions!
If you have any questions about the warranty service and technical support
contact seller of this product
No.101 Xinming West Road, Jintan Development Zone,
Changzhou Jiangsu China
Made In China
adainstruments.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>