Monsher MD 6003 Dishwasher User Manual

June 10, 2024
Monsher

**Monsher MD 6003 Dishwasher User Manual

**

SAFETY INFORMATION

| WARNING| When using your dishwasher, follow the precautions listed below:
---|---|---

  • Installation and repair can only be carried out by a qualified technician
  • This appliance is intended to be used in household.
  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  • Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision. (For EN60335-1) This appliance is not intended for use by persons (including children ) with reduced physical, sensory or 3 mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. (For IEC60335 1
  • Packaging material could be dangerous for children!
  • This appliance is for indoor household use only. To protect against the risk of electrical shock, do not immerse the unit, cord or plug in water or other liquid.
  • Please unplug before cleaning and performing maintenance on the appliance.
  • Use a soft cloth moistened with mild soap, and then use a dry cloth to wipe it again.

EARTHING INSTRUCTIONS

  • This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of an electric shock by providing a path of least resistance of electric current. This appliance is equipped with an earthing conductor plug.

  • The plug must be plugged into an appropriate outlet that is installed and earthed in accordance with all local codes and ordinances.

  • Improper connection of the equipment-earthing conductor can result in the risk of an electric shock.

  • Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded.

  • Do not modify the plug provided with the appliance; If it does not fit the outlet.

  • Have a proper outlet installed by a qualified electrician.

  • Do not abuse, sit on, or stand on the door or dish rack of the dishwasher.

  • Do not operate your dishwasher unless all enclosure panels are properly in place.

  • Open the door very carefully if the dishwasher is operating, there is a risk of water squirting out.

  • Do not place any heavy objects on or stand on the door when it is open. The appliance could tip forward.

  • When loading items to be washed:

    1. Locate sharp items so that they are not likely to damage the door seal;
    2. Warning: Knives and other utensils with sharp points must be loaded in the basket with their points facing down or placed in a horizontal position.
  • Some dishwasher detergents are strongly alkaline. They can be extremely
    dangerous if swallowed. Avoid contact with the skin and eyes and keep children away from the dishwasher when the door is open.

  • Check that the detergent powder is empty after completion of the wash cycle.

  • Do not wash plastic items unless they are marked “dishwasher safe” or the equivalent.

  • For unmarked plastic items not so marked, check the manufacturer’s recommendations.

  • Use only detergent and rinse agents recommended for use in an automatic dishwasher.

  • Never use soap, laundry detergent, or hand washing detergent in your dishwasher.

  • The door should not be left open, since this could increase the risk of tripping. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

  • During installation, the power supply must not be excessively or dangerously
    bent or flattened.

  • Do not tamper with controls.

  • The appliance needs to be connected to the main water valve using new hose sets. Old sets should not be reused.

  • To save energy, in stand by mode , the appliance will switch off automatically while there is no any operation in 30 minutes .

  • The maximum number of place settings to be washed is 14.

DISPOSAL

  • For disposing of package and the appliance please go to a recycling center.
    Therefore cut off the power supply cable and make the door closing deviceunusable.

  • Cardboard packaging is manufactured from recycled paper and should be disposed in the waste paper collection for recycling.

  • By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

  • For more detailed information about recycling of this product, please contact your local city office and your household waste disposal service.

  • DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.

PRODUCT OVERVIEW

| IMPORTANT| To get the best performance from your dishwasher, read all operating instructions before using it for the first time
---|---|---

Product Overview

  • Cutlery basket
    Cutlery basket

  • Upper basket
    Upper basket

  • Lower basket

NOTE:

  • Pictures are only for reference, different models may be different. Please prevail in kind.

USING YOUR DISHWASHER

Using Instruction

Before using your dishwasher:

  1. Set the water softener
  2. Loading the salt Into the softener
  3. Loading the basket
  4. Fill the dispenser

Please check the section 1 “Water Softener” of PART II: Special Version, If you need to set the water softener .

LOADING THE SALT INTO THE SOFTENER

NOTE:

If your model does not have any water softener, you may skip this section.
Always use salt intended for dishwasher use. The salt container is located beneath the lower basket and should be filled as explained in the following:
Loading The Salt Into The Softener

  1. Remove the lower basket and unscrew the reservoir cap.
  2. Place the end of the funnel (supplied) into the hole and pour in about 1.5kg of dishwasher salt.
  3. Fill the salt container to its maximum limit with water, It is normal for a small amount of water to come out of the salt container.
  4. After filling the container, screw back the cap tightly.
  5. The salt warning light will stop being after the salt container has been filled with salt.
  6. Immediately after filling the salt into the salt container, a washing program
    should be started (We suggest to use a short program). Otherwise the filter system, pump or other important parts of the machine may be damaged by salty water. This is out of warranty.

| WARNING| ; Only use salt specifically designed for dishwashers use! Every other type of salt not specifically designed for dishwasher use, especially table salt, will damage the water softener. In case of damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is liable for any damages caused. ; Only fill with salt before running a cycle. This will prevent any grains of salt or salty water, which may have been spilled, remaining on the bottom of the machine for any period of time, which may cause corrosion.
---|---|---

NOTE:

  • The salt container must only be refilled when the salt warning light ( ) in the control panel comes on. Depending on how well the salt dissolves, the salt
    warning light may still be on even though the salt container is filled. If there is no salt warning light in the control panel (for some Models), you can estimate when to fill the salt into the softener by the cycles that the dishwasher has run.

  • If salt has spilled, run a soak or quick program to remove it.

BASKET USED TIPS

Adjusting the upper basket

Type 1:
The height of the upper basket can be easily adjusted to accommodate taller dishes in either the upper or lower basket. To adjust the height of the upper rack, follow these steps:

  1. Pull out the upper basket.
    Basket Used Tips

  2. Remove the upper basket.
    Basket Used Tips

  3. Re-attach the upper basket to upper or lower rollers.
    Basket Used Tips

  4. Push in the upper basket.
    Basket Used Tips

Type 2:

  1. To raise the upper basket, just lift the upper basket at the center of each side until the basket locks into place in the upper position. It is not necessary to lift the adjuster handle.
    Basket Used Tips

  2. To lower the lift the upper basket, adjust handles on each side to release the basket and lower it to the lower position.
    Basket Used Tips

To make room for taller items in the upper basket, raise the cup rack upwards. You can then lean the tall glasses against it. You can also remove it when it is not required for use.
Folding Back Cup Shelves

Folding back the rack shelves
The spikes of the lower basket are used for holding plates and a platter. They can be lowered to make more room for large items.
Folding Back Cup Shelves

MAINTENANCE AND CLEANING

EXTERNAL CARE
The door and the door seal

Clean the door seals regularly with a soft damp cloth to remove food deposits. When the dishwasher is being loaded, food and drink residues may drip onto
the sides of the dishwasher door. These surfaces are outside the wash cabinet and are not accessed by water from the spray arms. Any deposits should be wiped off before the door is closed.
The control panel
If cleaning is required, the control panel should be wiped with a soft damp cloth only

| WARNING|

  • To avoid penetration of water into the door lock and electrical components, do not use a spray cleaner of any kind.
  • Never use abrasive cleaners or scouring pads on the outer surfaces because they may scratch the finish. Some paper towels may also scratch or leave marks on the surface.

---|---|---

INTERNAL CARE
Filtering system
The filtering system in the base of the wash cabinet retains coarse debris from the washing cycle. The collected coarse debris may cause the filters to clog. Check the condition of the filters regularly and clean them if necessary under
running water.
Follow the steps below to clean the filters in the wash cabinet.

NOTE:
Pictures are only for reference, different models of the filtering system and spray arms may be different.

  1. Hold the coarse filter and rotate it anticlockwise to unlock the filter. Lift the filter upwards and out of the dishwasher.
    Filtering system

  2. The fine filter can be pulled off the bottom of the filter assembly. The coarse filter can be detached from the main filter by gently squeezing the tabs at the top and pulling it away.
    Filtering system

  3. Larger food remnants can be cleaned by rinsing the filter under running water. For a more thorough clean, use a soft cleaning brush.
    Filtering system

  4. Reassemble the filters in the reverse order of the disassembly, replace the filter insert, and rotate clockwise to the close arrow.
    Filtering system

| WARNING|

  • Do not over tighten the filters. Put the filters back in sequence securely, otherwise coarse debris could get into the system and cause a blockage.
  • Never use the dishwasher without filters in place. Improper replacement of the filter may reduce the performance level of the appliance and damage dishes and utensils.

---|---|---

Spray arms
It is necessary to clean the spray arms regularly for hard water chemicals will clog the spray arm jets and bearings. To clean the spray arms, follow the instructions below:

  1. To remove the upper spray arm, hold the nut in the center still and rotate the spray arm counterclockwise to remove it.
    Spray Arms

  2. To remove the lower spray arm, pull out the spray arm upward.
    Spray Arms

  3. Wash the arms in soapy and warm water and use a soft brush to clean the jets. Replace them after rinsing them thoroughly.
    Spray Arms

CARING FOR THE DISHWASHER

Frost precaution

Please take frost protection measures on the dishwasher in winter. Every time
after washing cycles, please operate as follows:

  1. Cut off the electrical power to the dishwasher at the supply source.
  2. Turn off the water supply and disconnect the water inlet pipe from the water valve.
  3. Drain the water from the inlet pipe and water valve. (Use a pan to gather the water)
  4. Reconnect the water inlet pipe to the water valve.
  5. Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump.

After every wash
After every wash, turn off the water supply to the appliance and leave the door slightly open so that moisture and odors are not trapped inside.
Remove the plug
Before cleaning or performing maintenance, always remove the plug from the socket.
No solvents or abrasive cleaning
To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products. Only use a cloth with warm soapy water. To remove spots or stains from the surface of the interior, use a cloth dampened with water an a little vinegar, or a cleaning product made specifically for dishwashers.
When not in use for a longtime
It is recommend that you run a wash cycle with the dishwasher empty and then remove the plug from the socket, turn off the water supply and leave the door of the appliance slightly open. This will help the door seals to last longer and prevent odors from forming within the appliance.
Moving the appliance
If the appliance must be moved, try to keep it in the vertical position. If absolutely necessary, it can be positioned on its back.
Seals
One of the factors that cause odours to form in the dishwasher is food that
remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occurring.

INSTALLATION INSTRUCTION




| **WARNING

| Electrical Shock Hazard Disconnect electrical power before installing dishwasher. Failure to do so could result in death or electrical shock.
---|---|---
**
| ATTENTION| The installation of the pipes and electrical equipments should be done by professionals.
---|---|---

ABOUT POWER CONNECTION

****| **WARNING**| For personal safety:þ Do not use an extension cord or an adapter plug with this appliance.þ Do not, under any circumstances, cut or remove the earthing connection from thepower cord.
---|---|---

Electrical requirements
Please look at the rating label to know the rating voltage and connect the
dishwasher to the appropriate power supply. Use the required fuse 10A/13A/16A,
time delay fuse or circuit breaker recommended and provide separate circuit
serving only this appliance.
Electrical connection
Ensure the voltage and frequency of the power being corresponds to those on
the rating plate. Only insert the plug into an electrical socket which is earthed
properly. If the electrical socket to which the appliance must be connected is not
appropriate for the plug, replace the socket, rather than using a adaptors or the
like as they could cause overheating and burns.

Ensure that proper earthing exists before use.

WATER SUPPLY AND DRAIN

Cold water connection
Connect the cold water supply hose to a threaded 3/4 (inch) connector and make sure that it is fastened tightly in place.If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear. This precaution is needed to avoid the risk of the water inlet to be blocked and damage the appliance.

Ordinary supply hose
Water Supply
Safety supply hose

About the safety supply hose
The safety supply hose consists of the double walls. The hose’s system guarantees its intervention by blocking the flow of water in case of the supply hose breaking and when the air space between the supply hose itself and the outer corrugated hose is full of water.

| WARNING| A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has one, it is recom- mended that the hose be disconnected and thehole plugged.
---|---|---

How to connect the safety supply hose

  1. Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher.
  2. Tighter the screws of the safety supply hose to the faucet with thread 3/4 inch.
  3. Turn water fully on before starting the dishwasher.

How to disconnect the safety supply hose

  1. Turn off the water.
  2. Unscrew the safety supply hose from the faucet.

CONNECTION OF DRAIN HOSES
Insert the drain hose into a drain pipe with a minimum diameter of 4 cm, or let it run into the sink, making sure to avoid bending or crimping it. The height of drain pipe must be less than 1000mm. The free end of the hose must not be immersed in water to avoid the back flow of it.

  Please securely fix the drain hose in either position A or position B.
Connecting Instruction

How to drain excess water from hoses
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directly into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable container that is held outside and lower than the sink.
Water outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoidwater leaks. Ensure that the water drain hose is not kinked or squashed.
Extension hose
If you need a drain hose extension, make sure to use a similar drain hose. It must be no longer than 4 meters; otherwise the cleaning effect of the dishwasher could be reduced.
Syphon connection
The waste connection must be at a height less than 100 cm (maximum) from the bottom of the dish. The water drain hose should be fixed .

POSITION THE APPLIANCE
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can be positioned either to the right or the left sides to facilitate proper installation.
Levelling the appliance
Once the appliance is positioned for levelling, the height of the dishwasher may be altered via adjustment of the screwing level of the feet. In any case,the appliance should not be inclined more than 2°.
Levelling The Appliance

NOTE:
Only apply to the free standing dishwasher.

FREE STANDING INSTALLATION

Fitting between existing carbinets
The height of the dishwasher, 845 mm, has been designed in order to allow the machine to befitted between existing cabinets of the same height in modern fitted kitchens. The feet can be adjusted so that correct height is reached. The laminated top of the machine does not require any particular care since it is heatproof, scratchproof and stainproof.
Free Standing Installation

Underneath existing work top
(When fitting beneath a work top) In most modern fitted kitchens there is only one single work top under which cabinets and electrical appliances are fitted. In this case remove the work top of the dishwasher by unscrewing the screws under the rear edge of the top **(a).

**

| ATTENTION| After removing the work top, the screws must be screwed again under the rear edge of the top ( b ).The height will then be reduced to 815 mm, as scheduled by the International Regulations (ISO) and the dishwasherwill fit perfectly under the kitchen working top.
---|---|---

BUILT-IN INSTALLATION(FOR THE INTEGRATED MODEL)
TEP 1. Selecting the best location for the dishwasher
The installation position of dishwasher should be near the existing inlet and
drain hoses and power cord. Illustrations of cabinet dimensions and installation position of the dishwasher.

  1. Less than 5 mm between the top of dishwasher and cabinet and the outer door aligned to cabinet.
    Installation Instruction

  2. If dishwasher is in stalled at the corner of the cabinet, there should be some space when the door is opened.
    Installation Instruction

NOTE:
Depending on where your electrical outlet is, you may need to cut a hole in the opposite cabinet side.

STEP 2. Aesthetic panel’s dimensions and installation

****The aesthetic wooden panel could be processed according to the installation drawings.

Semi-integrated model
Magical paster A and magical paster B be disjoinedon ,magical paster A on the aesthetic wooden panel and felted magical paster B of the outer door of dishwasher (see figure A ). After positioning of the panel , fix the panel onto the outer door byscrews and bolts (See figure B )
Semi-integrated Model
Semi-integrated Model
Full-integrated model
Install the hook on the aesthetic wooden panel and put the hook into the slot of the outer door of dishwasher (see figure A). After positioning of the panel , fix the panel onto the outer door by screws and bolts (See figure B).
Full-integrated Model
Semi-integrated Model

STEP 3. Tension adjustment of the door spring

  1. The door springs are set at the factory to the proper tension for the outer door. If aesthetic wooden panel are installed, you will have to adjust the door spring tension. Rotate the adjusting screw to drive the adjustor to strain or relax the steel cable.
  2. Door spring tension is correct when the door remains horizontal in the fully opened position, yet rises to a close with the slight lift of a finger.
    Semi-integrated Model

STEP 4. Dishwasher installation steps

Please refer to the specified installation steps in the installation drawings.

  1. Affix the condensation strip under the work surface of cabinet. Please ensure the condensation strip is flush with edge of work surface. (Step 2)
  2. Connect the inlet hose to the cold water supply.
  3. Connect the drain hose.
  4. Connect the power cord.
  5. Place the dishwasher into position. (Step 4)
  6. Level the dishwasher. The rear food can be adjusted from the front of the dishwasher by turning the in the middle of the base of dishwasher use an . To adjust the front feet, use a flat screw driver and turn the front feet until the dishwasher is level. (Step 5 to Step 6)
  7. Install the furniture door to the outer door of the dishwasher. (Step 7 to Step 10)
  8. Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to tighten the left and right door springs. Failure to do this could cause damage to your dishwasher. (Step 11)
  9. The dishwasher must be secured in place. There are two ways to do this:
    • Normal work surface: Put the installation hook into the slot of the side plane and secure it to the work surface with the wood screws.
    • Marble or granite work top: Fix the side with Screw.
      Adjustment

STEP 5. Levelling the dishwasher

Dishwasher must be level for proper dish rack operation and wash performance.

  1. Place a spirit level on door and rack track inside the tub as shown to check that the dishwasher is level.
  2. Level the dishwasher by adjusting the three levelling legs individually.
  3. When level the dishwasher, please pay attention not to let the dishwasher tip over.
    Installation Instruction

NOTE:
The maximum adjustment height of the feet is 50 mm.

TROUBLESHOOTING

Before Calling For Service
Reviewing the charts on the following pages may save you from calling for service.

PROBLEM POSSIBLE CAUSES Stained tub interiorDetergent with colourant may have been used. White film on inside surface  Hard water minerals. ____ There are rust stains on cutleryThe affected items are not corrosion resistant.Knocking noise in the dishwasher.A spray arm is knocking against an item in a basket.Rattling noise in the dishwasher.Items of crockery are loose in the dishwasher. Knocking noise in the water pipes.This may be caused by on- site installation or the cross- section of the piping. ____ The dishes are not clean The dishes were not loaded correctly. Problem Possible Causes __ The dishes are not clean. Not enough detergent was dispensed. Cloudiness on glass- ware. Combination of soft water and too much detergent. White spots appear on dishes and glasses .Hard water area can cause limescale deposits. Black or grey marks on dishes. Aluminium utensils have rubbed against dishes. Detergent left in dis- penser. Dishes block detergent dis- penser. __ The dishes aren’t drying. Improper loading. PROBLEM POSSIBLE CAUSES __ The dishes aren’t drying.Wrong program has been selected.

PROBLEM POSSIBLE CAUSES WHAT TO DO

Dishwasher doesn’t start

| Fuse blown, or the circuit break tripped.| Replace fuse or reset circuit breaker.Remove any other appliances sharing the same circuit with the dishwasher.
Power supply is not turned on.| Make sure the dishwasher is turned on and the door is closed securely.Make sure the power cord is properly plugged into the wall socket.
Water pressure is low| Check that the water supply is connected properly and the water is turned on.
Door of dishwasher not properly closed.| Make sure to close the door properly and latch it.

Water not pumped form dishwasher

| Twisted or trapped drain hose.| Check the drain hose.
Filter clogged.| Check coarse the filter.
Kitchen sink clogged.| Check the kitchen sink to make sure it is draining well. If the problem is the kitchen sink that is not draining, you may need a plumber rather than a serviceman for dishwashers.

Suds in the tub

|

Wrong detergent.

| Use only the special dishwasher detergent to avoid suds. If this occurs, open the dishwasher and let suds evaporate. Add 1 gallon of cold water to the bottom of the dishwasher.Close the dishwasher door, then select any cycle. Initially, the dishwasher will drain out the water. Open the door after draining stage is complete and check if the suds have disappeared.Repeat if necessary.
Spilled rinse-aid.| Always wipe up rinse-aid spills immediately.
WHAT TO DO
Make sure that the detergent has no colourant.
To clean the interior, use a damp sponge with dish- washer detergent and wear rubber gloves. Never use any other cleaner than dishwasher detergent otherwise, it may cause foaming or suds.
Avoid washing items that are not corrosion resistant in the dishwasher.
A program was not run after dishwasher salt was added. Traces of salt have gotten into the wash cycle.| Always run a wash program without any crockery after adding salt. Do not select the Turbo function (if present), after adding dishwasher salt.
The lid of the softer is loose.| Check the softener lid is secure.
Interrupt the program and rearrange the items which are obstructing the spray arm.
Interrupt the program and rearrange the items of crockery.
This has no influence on the dishwasher function. If in doubt, contact a qualified plumber.
See PART II “Preparing And Loading Dishes”.
The program was not power- ful enough.| Select a more intensive program.
What To Do
Use more detergent, or change your detergent.
Items are blocking the move- ment of the spray arms.| Rearrange the items so that the spray can rotate freely.
The filter combination is not clean or is not correctly fitted in the base of wash cabinet.This may cause the spray arm jets to get blocked.|

Clean and/or fit the filter correctly. Clean the spray arm jets.

Use less detergent if you have soft water and select a shorter cycle to wash the glassware and to get them clean.
Add more detergent.
Use a mild abrasive cleaner to eliminate those marks.
Re-loading the dishes properly.
Load the dishwasher as suggested in the directions.

Dishes are removed too soon.

| Do not empty your dishwasher immediately after washing. Open the door slightly so that the steam can come out. Take out the dishes until the inside temperature is safe to touch. Unload the lower basket first to prevent the dropping water from the upper basket.
WHAT TO DO
With a short program, the washing temperature is lower, decreasing cleaning performance.Choose a program with a long washing time.
Use of cutlery with a low- quality coating.| Water drainage is more difficult with these items. Cutlery or dishes of this type are not suitable forwashing in the dishwasher.

LOADING THE BASKETS ACCORDING TO EN 50242
  1. Upper basket:
    Loading The Basket NUMBER| ITEM
    ---|---
    1| Cups
    2| Saucers
    3| Glasses
    4| Small serving bowl
    5| Medium serving bowl
    6| Large serving bowl
  2. Lower basket:
    Loading The Basket NUMBER| ITEM
    ---|---
    7| Dessert dishes
    8| Dinner plates
    9| Soup plates
    10| Oval platter
  3. Cutlery basket:
    Loading The Basket

Loading The Basket

NUMBER ITEM
1 Soup spoons
2 Forks
3 Knives
4 Teaspoons
5 Dessert spoons
6 Serving spoons
7 Serving forks
8 Gravy ladles

Information for comparability tests in accordance with EN 50242
Capacity: 14 place settings
Position of the upper basket: lower position
Program: ECO
Rinse aid setting: 6
Softener setting: H3

Cutlery Rack Used Tips

Lift the left basket up, adjust it to lower position, left basket is flat and right basket is sideling.
Cutlery Rack

Lift the right basket up, both left and right baskets are flat.
Cutlery Rack

Move the right basket from right to left, two basket are overlapping.

Remove the right basket from the tray, only has the left basket.
Cutlery Rack

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals