Monsher MOE 6026 Built-in Electric Oven User Manual

Monsher MOE 6026 Built-in Electric Oven

DEAR OUR PRECIOUS CUSTOMER, Thank you for choosing a Monsher product. We would like you to be satisfied with our product, which has been produced in our highly qualified, technological and modern facilities. You can use your oven with pleasure and confidence for many years by performing required maintenance and showing necessary care. Read the whole manual. Retain the manual during use of the product. If you hand the product over to someone else, give them the manual as well.

NOTE. This Operating Manual is prepared for multiple models. Some of the features mentioned may not be available in your product.

TECHNICAL FEATURES

IMPORTANT SAFETY WARNINGS

Read the manual carefully before installation and use of the appliance. The appliance shall not be covered under warranty in case of an incorrect installation or use performed by a person other than a specialist.

• Follow the safety related instructions.
• Also read other documents that are provided together with the appliance.
• The user manual may be convenient for more than one model.
• Keep it in an easily accessible place for a future use.
• Disconnect all the energy connections before installation, maintenance and repair operations.
• If the appliance is damaged, do not operate it.
• Keep the children under 8 years old and the pets away during and after use of the appliance.
• It is dangerous for the children under 8 years old to touch the appliance without an adult supervision and to use it on their own.
• Keep the packaging materials out of reach of the children, dispose them in a place where they cannot reach.
• Do not bring damp package into contact with the mouth. Keep it out of reach of the children.
• The appliance should not be maintained and cleaned as long as the children are not under the supervision of the adults.
• The appliance is only intended for cooking. Do not use the appliance for the pur-poses such as heating the room.
• While the oven is hot, tray and accessories may become hot; use oven gloves or a similar apparatus when you place and remove them.
• Do not use steam cleaner for cleaning the appliance.
• Keep the surrounding area of all the compartments, where there is an air circula-tion, open.
• If you would use an oily baking paper, absolutely do not bring the paper into contact with the base of the oven.
• Do not prepare food with strong alcoholic drinks. Alcohol vaporates at a high tem-perature, it may catch and cause fire in case of contact with hot surfaces.
• Check whether the appliance is turned off or not after use.
• Keep the cooking duration under control.

ELECTRICAL HAZARD
There is a risk of electrocution.

• The appliance should be repaired by an authorized service if it is damaged.

• In case of any damage, turn off the appliance, cut off the electricity.

• Due to the risk of electric shock, do not wash the appliance by spraying or pouring water on it.

• If the lamp would be replaced, disconnect the appliance from the electrical outlet in order to avoid electric shock.

• Our company is not responsible from any damage that would arise for the reason that the appliance is used without connecting it in accordance with local regula-tions.

• Absolutely do not use the plug with wet hands.

• In order to disconnect the appliance from the electrical outlet, plug it out by holding the plug, not the cable.

• While the appliance operates, its rear surface also gets warm. The electrical con-nections should not come into contact with the rear surface.

• Unplug the appliance during operations such as cleaning, repair and maintenance.

• Do not pass the connection cables over the hot surface. If the cables melt, they may cause a short circuit or a fire.
  WARNING. Do not try to extinguish the fire with water.

• Disconnect the appliance from the electrical outlet and try to cover the fire with an instrument such as a fire blanket in order to prevent the fire from coming into contact with the air.
  RISK OF INJURY

• If there is a crack on the oven door glass or it is exposed to an impact, the glass may break and splatter.

• In order to clean the oven door glass, do not use harsh and abrasive cleaners or metal scrapers.

• Do not touch the heating/power elements.

• The hinges of the appliance door may jam the door during movement. Do not hold the section which contains hinges.

• Never leave combustible materials or oxidizers in the appliance.

• Do not heat glass jars and canned food. Created pressure may cause the jar to explode.

• Do not put the tray close to combustible materials or oxidizers after cooking.

• The oven door may consist of 2, 3 or 4 glasses. Do not use the oven door with a removed glass.

• The user should not carry the oven on his/her own without gloves..

INTENDED USE

• The appliance is intended for cooking. Do not use it for purposes such as heating.
• The appliance has been designed for domestic use. Use it only in a closed area.
• The oven can be used for defrosting, frying or grilling the food.
• Do not use the oven for drying purposes by hanging a towel or clothes on its handle.

ENVIRONMENTAL PROTECTION

SAVING ENERGY

To learn what should be done while cooking a food in the oven, first of all, we need to talk about pre-heating. You should apply pre-heating only when it is required. Pay attention not to apply pre-heating for more than 10 minutes.

• Before cooking, put the frozen food in the oven after you leave them at the room temperature or defrost them in the microwave oven.
• Do not leave unnecessary accessories in the cooking compartment.
• You can cook more than one food on the wire rack at the same time. Thereby, you save heat.
• The oven door causes heat loss every time it is opened. For this reason, you should not open the oven door unless it is highly necessary. When you need to open the oven door, pay attention to close it as soon as possible.

INSTALLATION MANUAL

APPLIANCE DIMENSIONS
The dimensions mentioned in the image are in mm.

• 20 mm Glass Panel
• 21 mm Inox Panel

IMPORTANT WARNINGS

Check the suitability of the electrical wiring to make the appliance ready for use. If it is not suitable, call a plumber and have him make the required arrangements. You shall use the appliance safely when you install the appliance as described in the installation manual. The person, who installs the appliance, is responsible for the malfunctions oc-curred due to incorrect installation.

WARNING. The customer is responsible for preparing the place where the appli-ance would be put and the electrical wiring.

WARNING. Our manufacturing company is not responsible for the problems that may occur due to the operations performed by the people other than the authorized ones and the warranty shall be deemed as invalid.

• Carry the appliance together with at least two people. Lift the appliance while car-rying so it does not damage the floor.
• The appliance should be checked after its package is opened. In case of a damage, it should not be installed.
• The components may be sharp, wear protective gloves during installation
• The appliance should be installed in accordance with the rules related to the elec-tricity and gas mentioned in the local standards.
• The dimensions mentioned in the image, are in mm.
• Kitchen cabinets should be on the same level with the appliance and fixed.
• Do not mount the appliance in a decoration or closed furniture. It is dangerous due to overheating.
• The furniture, where the installation would be applied, (min. 1000C) should be made of durable material.
• It is not recommended to install the appliance close to the cooler. The of these appliances might be impacted negatively due to the heat.

ELECTRICITY CONNECTION AND SAFETY

WARNING. Power grid should be disconnected during installation. Do not turn it on until the installation ends.

• The appliance should be installed correctly by the authorized service technician in accordance with the specified instructions.
• Do not pass the connection cables over the hot surface. When the cables melt, they may cause a short circuit or a fire.
• If the cables are damaged,they should be replaced by an electrician.
• They should be plugged into a (grounded) outlet in the grounding system in accordance with the rules.

If there is not a suitable outlet, call the electrician and have your electrical wiring checked.

• Make sure that your plug is grounded.
• The company is not responsible for the damages caused by the ungrounded outlets where the appliance is plugged in.
• If the product has a cable and a plug; an electrical connection is established by plugging the appliance in a grounded outlet.
• If the product has a cable but not a plug; coding should be performed by an expert suitably
  • Grounding cable = E Green – Yellow
  • Neutral cable = N Blue
  • Phase cable = L Brown

INSTALLATION

INSTALLING BELOW COUNTER

• The cabinet should be in compliance with the dimensions mentioned in figure 2.
• You need to unload the rear compartment of the cabinet in the dimensions mentioned in figure 2 for necessary ventilation.

INSTALLING INTO A TALL CABINET

• The cabinet should be in compliance with the dimensions mentioned in figure 3.
• You need to unload the rear compartment of the cabinet in the dimensions mentioned in the figure for necessary ventilation.
• Moreover, if there is a back panel in the tall cabinet, it should also be removed.

VENTILATION
In order for you to get better efficiency from your oven, there should be adequate cold air intake. Leave suitable spaces according to the dimensions mentioned in Figure 4.

INSTALLING ON THE CORNER
The installation should be in compliance with the specified dimensions to perform the installation mentioned in Figure 5 and to be able to open the appliance door.

FIXING THE APPLIANCE

• Center the appliance and push it completely into the furniture.
• Power cable should not be bent under the oven and between the oven and the furniture.
• Open the appliance door.
• Fix the appliance with the screws provided along with it.
• Screw the appliance into the holes, which are shown in figure 6.
• Make sure that the oven is fixed. Otherwise, there is a risk of tilting during use.

LAST CHECKS

• Turn on the electricity after performing the installation.
• Read the user manual for using the appliance.

REMOVING THE APPLIANCE

• Turn off the electricity.
• Remove the fixing screws.
• Lift the appliance together with at least two people by pulling it out.

FUTURE CARRYING PROCEDURES
While carrying the appliance in the future;

• Retain the original box of the appliance. In case there is no original box, tape and wrap it with a bubble packaging or a thick cardboard tightly.
• If there is an accessory in it, place a cardboard in the size of the oven door so the oven door is not damaged. Tape the door to prevent it from opening.

WARNING. Do not lift the oven by holding its handle or door.

WARNING. Do not place an item on the product, carry it uprightly.

INTRODUCING THE APPLIANCE

GENERAL OVERVIEW

1. Control Panel
2. Air Vents
3. Oven Illumination
4. Racks
5. Fan
6. Fan Protection Sheet
7. Cover
8. Handle

• Air Vents may be open/closed depending on your model. It may not be available depending on your
• FPS model. The position of the
• Oven Illumination may vary.
• Racks may vary depending on your model. Wire rack is demonstrated as an example

CONTROL PANEL

FUNCTION KNOB
Heating/cooking type is adjusted with function selection button. You also need to set temperature button to a value with function selection button. Otherwise, the product will not start to heat.

TEMPERATURE KNOB
It allows you to select the temperature of the oven. The cooking is started by selecting the function type.

MECHANICAL TIMER
It allows you to determine the time for the food to be cooked. The function and temperature knob must also be set.

SIGNAL LAMP
It is the lamp which indicates that the oven is heated. It goes out when the ovenreaches to the adjusted temperature.

TURNING OFF THE ELECTRIC OVEN
Switch the function and temperature buttons to zero (turned off) position.

HEATING TYPES AND FUNCTIONS

NOTE. The functions, which are available on the table, may vary in the different appliances, they may not be available in every model.

The related energy value in the fan supported cooking mode has been indicated based on this function. The performed tests have been based on TS EN 60350 standard and (EV) No 66/2014 regulation

POP-OUT BUTTON USE

• In the models with a pop-out button, the button should be on the outside in order to apply the setting. (This button is optional.)
• Remove the button out by pressing on it as shown in the picture.
• You can adjust the button by turning it when it is outside.

USE OF THE OVEN

FIRST USE

NOTE : The surfaces become warmer than normal during the first operation. For this reason, do not touch the oven and keep the children away.

DAILY USE

• In order to start cooking, adjust the thermostat button of the oven and the suitable temperature (Cooking Recommendations) for the food.
• Preheat the oven, if pre-heating is desired.
• After cooking, leave the oven to cool down while its door is open. When the cooking duration ends, remember to turn off the oven’s function and temperature button.

USE OF MECHANICAL TIMER
It allows you to set the time for the food to be cooked. You can set it by selecting the temperature and type of cooking, turning the cooking time clockwise. When the time is up, it warns with a ringing sound. If you wish, you can start cooking by selecting the temperature and type of cooking without selecting a time by setting it to M mode

ACCESSORIES

The accessories, which are provided based on the model of the appliance, vary. The accessories, which are mentioned in the user manual, may not be available in the product.

NOTE. Use the original accessories, which are designed for the appliance.

STANDARD TRAY
It is intended for frozen food, cakes, large sized meat dishes, pastries.

WIRE RACK
It is intended for cake and soufflé moulds and for placing the food to be fried on the rack.

DEEP TRAY
You can use it for stews, fried food in large pieces and for collecting the dripping oils when you grill the food

USE OF ACCESSORIES

• There are models with wire and self adjusting racks. Wire rack has 6 cooking rack.
• Accessories should be placed between two racks and the side with a inclination should face the door of the appliance.
• The cavities on the wire rack prevent it from falling off the racks and ensure the safety.
• You can use the tray as a drip tray for grilled food and meat dishes by placing the tray and the rack together.

COOKING SUGGESTIONS

You can see the details of the food, which we have tested in our laboratories and whose cooking values have been determined by us, in the table. The cooking times may vary depending on the grid voltage, the nature and the amount of the material to be cooked and the temperature. By trying out, you can change the values to achieve different tastes and the results, which are suitable for your palatal delight. The lowest rack of the oven is the 1st rack. It is recommended to apply 10 min. pre-heating.

GRILLING TABLE
It is recommended to apply 5 min. pre-heating

MAINTENANCE AND CLEANING

Before starting to perform maintenance and cleaning, disconnect the applian- cefrom the electrical outlet against the risk of electric shock. Before performing maintenance, make sure that the appliance is cold. You can extend the lifetime of the appliance by performing regular maintenance and cleaning. You can remove the door, the glass and the racks for cleaning.

• Do not use scratching, abrasive tools such as knives, brushes on the internal and frontal parts, trays and other parts of the appliance. Clean and dry the appliance with warm water and soapy, soft cloth.
• Clean and dry the accessories thoroughly after use. Do not wash the accessories in the dishwasher.
• The appliance should be cleaned thoroughly after use. The wastes, accumulated oils may cause fire.

STEAM CLEANING
The dirt can be wiped easily by softening them after cooking. Remove all the accessories (if there is a wire rack) from the oven. Place the single tray on the lowest base by adding some water in it and by selecting Lower Heating function, operate the oven at for 100°/20 minutes. At the end of the operation, wipe the inside of the oven with a damp cloth or sponge.

REMOVING THE OVEN DOOR

ATTACHING THE OVEN DOOR

REMOVING THE GLASSES
The number of the glasses may vary according to the model

ATTACHING THE GLASSES

REMOVING THE WIRE RACKS

WARNING.The racks may be hot, do not touch the racks when they are hot. Wait for them to cool down. The cleaning process of the oven’s side walls may vary depending on the appliance model. This feature may not be available in your appliance.

ATTACHING THE WIRE RACKS

REPLACING THE OVEN LAMP

WARNING. Due to the hazard of electric shock, make sure that the power is out before replacing the lamp. The lamp may be hot, wait for it to cool down.

TROUBLESHOOTING

The malfunctions mentioned here are the situations that may occur usually. You can solve these problems easily without interfering with the product yourself. If the problem cannot be solved despite the instructions, call the dealer or the Authorized Service where you have bought the appliance from. In this case, never try to repair the appliance on your own.

The appliance does not operate.

| The appliance may not be plugged in.| Make sure that the appli- ance is plugged in.
The fuse may have blown or be broken.| Check the fuses in the fuse box. If the fuse has blown, engage it.
While the appliance operates, steam comes out.| The oven is used for the first time.| Steam may come out du- ring operation. This is not a malfunction.

The outside of the oven becomes too hot during cooking.

|

It is in a place, which is not well- ventilated.

|

Apply the spaces, which are indicated in the installation manual.

The oven does not cook properly.

|

The oven door may open too much during cooking.

| Do not open the door too much to ensure that the internal temperature does not decrease.

The cooling fan still ope- rates after the cooking ends.

| It operates for a while in order to ventilate the insi- de of the oven.|

This is not a malfunction.

Metal sounds come while the appliance gets warm or cools down.| The sounds, which are heard because the parts expand as a result of the heat, are normal.|

This is not a malfunction

The door is not closed entirely.

|

The leftovers may be stuck inside the oven and on the door.

|

Clean the oven.

The oven does not heat.

| :> The door may have remained open.

:> The function or the temperature may not have been adjusted.

:> The power may not be supplied.

|

:> Check the door and make sure that it is closed entirely.

:> Switch the oven to a specified temperature and/or the function.

Please note!
The following shall not be considered as defects of the Product

Electric and gas ovens

| Discoloration of product materials when using
---|---
Minor technical smells coming from a new product during the initial operation period
Surface darkening of enameled trays

DISPOSAL OF THE PRODUCT

COMPLIANCE WITH WEEE REGULATION AND DISPOSAL OF THE PRODUCT
Dispose of the old product in a way not harming the environment. On this product, there is a symbol (WEEE), which indicates that electrical and electronic equipment wastes should be collected separately. This means that the equipment should be handled in accordance with 2002/96/EC EU Directive for recycling or dismantling in order to minimize the impacts of it on the environment. For further information, please refer to local or regional authorities. The electronic products, which are submitted for controlled waste collection, pose a potential hazard in terms of both environmental health and human health due to the harmful materials they contain. You can consult with your authorized dealer or the garbage collection centre of your municipality about how you can dispose of the product. Before disposing of the product, unplug the power cord and break the cover lock, if present, to protect children from danger. Essential: Energy label information have been indicated according to EN 60350-1 / IEC 60350-1 standards for domestic type electric ovens. The values are determined according to standard load, lower-upper heater or fan supported heating (if any) functions. The properties are subject to change without giving a prior notice in order to increase the quality of the product.

SERIAL NUMBER CHART

MANUFACTURERS:
M&G HAUSGERATE GMBH Potsdamer Str. 92 10785 Berlin Tel : (030) 544 37 834 Fax: (030) 544 37 856

FACTORIES-BRANCHES OF THE MANUFACTURER:
«FEMAS METAL SANAYI VE TICARET ANONIM SIRKETI» ORGANIZE SANAYI BOLGESI 9. CADDE NO: 17 MELIKGAZI, KAYSERI, turkey «TEKA INDUSTRIAL, S.A.»

IMPORTERS:
LLC «MG Rusland», 141400 Moscow region, Khimki, Butakovo, 4

The manufacturer reserves the right to make any changes to design, outside appearance and scope of supply of appliance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>