westfalia 961197 Self Centering Dowelling Jig Instruction Manual
- June 10, 2024
- Westfalia
Table of Contents
961197 Self Centering Dowelling Jig
Instruction Manual
Dear Customers,
Instruction manuals provide valuable hints for using your new device. They
enable you to use all functions, and they help you avoid misunderstandings and
prevent damage. Please take the time to read this manual carefully and keep
it for future reference.
If you pass the device on to third parties, enclose these instructions.
SAFETY NOTES
Please note the included General Safety Notes and the following safety notes to avoid malfunctions, damage or physical injury:
- Please read this manual carefully and use the device only according to this manual.
- Dispose of used packaging material carefully or store it out of the reach of children. There is a danger of suffocation!
- People with limited physical, sensory or mental capabilities may only use the dowelling jig under the supervision and instruction of a supervisor.
- This article is not a toy. Do not let children play with the dowelling jig.
- Only use the dowelling jig with twist drills for wood, plastic and metal, it is not suitable for hard metal-tipped masonry drills!
- Only use drills with a diameter that matches the holes in the jig or the bushings.
- Be careful not to tilt the drill in the device, the drill can break off and cause serious injuries.
- If the dowelling jig is damaged, stop using it and have it repaired by a specialist or contact our customer service. Do not disassemble the dowelling jig or try to repair it yourself.
Operation
Intended Use
The dowel jig is used to drill cantered holes in sizes 6, 8, 19, 11 and 12 mm
for wooden dowels in the edge of a board or similar component with a width of
10 to 51 mm. The jig center’s itself automatically when it is put on.
Operation
Four holes are made in the black middle part of the dowel jig. There are two
threaded holes for inserting drill bushings and two cylinder holes with 11 to
12 mm diameter. The drill bushings with an inner diameter of 6, 8 or 10 mm can
be screwed into the threaded holes. Two bushings can be used to drill holes
next to each other.
Prepare the dowel jig by inserting the appropriate drill bushings, if
necessary, and fix the dowel jig at the desired location on the edge of the
component to be drilled by tightening the clamping screw. The dowel jig
centres itself automatically. Then drill the holes to the desired depth. Be
careful not to tilt the drill. Tilting the drill can break it and lead to
serious injuries!
Cleaning
- Blow off residues from the dowel jig with compressed air or clean the dowel jig with a stiff brush and a slightly dampened cloth. If necessary, protect the dowelling jig from corrosion with a little oil.
- To avoid damaging the surfaces, do not use any harsh chemicals or abrasives.
Included
- Self-centering Dowel Jig
- 2x Drill Bushings 10 mm inside Diameter
- 2x Drill Bushings 8 mm inner Diameter
- 2x Drill Bushings 6 mm inner Diameter
DISPOSAL
Dear Customer,
Please help avoid waste materials.
If you at some point intend to dispose of this article, then please keep in
mind that many of its components consist of valuable materials, which can be
recycled. Please do not discharge it in the rubbish bin, but check with your
local council for recycling facilities in your area.
CUSTOMER SERVICES
SCHWEIZ
Westfalia
Wydenhof 3a
CH-3422 Kircher (BE)
Telephone: (034) 4 13 80 00
Telefax: (034) 4 13 80 01
Internet: www.westfalia-versand.ch
References
- Westfalia Versand Österreich | Werkzeug ✓ Garten ✓ Technik ✓ & mehr
- Westfalia Versand Schweiz | Werkzeug ✓ Garten ✓ Technik ✓ & mehr
- Westfalia Versand Deutschland | Werkzeug ✓ Garten ✓ Technik ✓ & mehr
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>