SIGNATURE HARDWARE 440713 1-Light 15-Inch Brushed Nickel Incandescent Flush Mount Light Owner’s Manual

440713 1-Light 15-Inch Brushed Nickel Incandescent Flush Mount Light

Product Information

The Nassau SKU 440713 is an electric fixture that requires professional installation. It comes with mounting screws, outlet box screws, a mounting bar, a canopy, a glass, a plastic washer, a finial, a nut, a nipple, and a coupling. The product requires a light bulb with a maximum wattage of A19 100 watts. It also requires basic tools such as screwdrivers, wire strippers, wire cutters, and electrical tape. The product must be installed according to local plumbing and building codes.

Product Usage Instructions

1. Consult a professional if you are unfamiliar with installing electric fixtures.

2. Unpack and inspect the product for shipping damage. If any damage is found, contact Signature Hardware Customer Relations via live chat at www.signaturehardware.com or by emailing
   support@siganturehardware.com.

3. Gather all the materials required for installation, including the tools and the light bulb.

4. Thread the mounting screws (C) into the matching holes in the mounting bar (B).

5. Secure the mounting bar (B) to the outlet box with outlet box screws (A).

6. Connect the wires according to local electrical codes and tuck them carefully inside the outlet box.

7. Raise the canopy (D) allowing for the mounting screws (C) to protrude through the key slots. Rotate the canopy (A) clockwise until the mounting screws (C) are in the narrow part of the key slots, and tighten with a screwdriver.

8. Slide the glass (H) and the plastic washer (I) onto the nipple (G) then secure with the finial (J).

9. Thread the nut (F) onto the nipple (G) and thread the nipple (G) into the coupling (E).

10. Install the light bulb according to the manufacturer’s instructions.

If you have additional questions, visit www.signaturehardware.com for product and warranty information, or contact Signature Hardware Customer Relations via live chat or by emailing support@signaturehardware.com.

BEFORE YOU BEGIN

We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or for personal injury during installation. Observe all local plumbing and building codes. Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer Relations team via live chat at www.signaturehard- ware.com or by emailing support @siganturehard-ware.com.

GETTING STARTED

Ensure that you have gathered all the required materials that are needed for the installation.

FOR YOUR SAFETY

WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully, if you are unclear as to how to proceed, consult a qualified electrician.

TOOLS AND MATERIALS

INSTALLATION (FIG. 1)

1. Thread the mounting screws (C) into the matching holes in the mounting bar (B).

2. Securem ountingb ar (B)t o the outlet box with outlet box screws (A).

3. Connect the white wire from the fixture to the white wire from the outlet box and the black
   wire from the fixture to the black wire from the outlet box. Cover the two wire connections using the two provided wire connectors. Wrap the two wire connections with electrical tape for a more secure connection. Attach the grounding wire connections with electrical tape for a more secure connection. Connect he copper ground wires from the fixture and from the outlet box to the ground screw on the mounting bar.
   Note: If you have electrical questions, consult your local electrical code for approved grounding methods.

4. After wires are connected, tuck them carefully inside outlet box. Raise th e canopy (D) allowing for the mounting screws (C) to protrude through the key slots. Rotate the canopy (A) clockwise until the mounting screws (C) are in the narrow part of the key slots, and tighten with a screwdriver.

INSTALLATION (FIG. 2)

1. Thread the nut (F) onto the nipple (G) and thread the nipple (G) into the coupling (E).
2. Install light bulbs (Not provided). Please do not exceed the maximum wattage capacity recommended on the socket. We recommend the use of a clear light bulb.
3. Slide the glass (H) and the plastic washer (I) onto the nipple (G) then secure with the finial (J).

1.855.715.1800
signaturehardware.com

References

• ware
• Signature Hardware - Shop Unique, Quality Decor

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>