SIGNATURE HARDWARE 440804 Bankloft 1-Light Polished Nickel Incandescent Flush Mount Light Owner’s Manual

440804 Bankloft 1-Light Polished Nickel Incandescent Flush Mount Light

Product Information

BANKLOFT SKU 440804

The BANKLOFT SKU 440804 is an electric fixture that can be mounted in two ways: flush mount or semi-flush mount. It comes with a crystal with rod set assembly and requires a light bulb (A19 100 watt maximum), safety glasses, wire stripper, step ladder, Phillips and flathead screwdrivers, wire cutters, and electrical tape for installation. The fixture must be installed in compliance with local plumbing and building codes, and Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, countertop, or personal injury during installation.

Product Usage Instructions

1. We recommend consulting a professional if you are unfamiliar with installing electric fixtures.
2. Unpack and inspect the product for shipping damage. If any damage is found, contact Signature Hardware Customer Relations team via live chat at www.signaturehardware.com or by emailing support@siganturehardware.com.
3. Gather all the required materials that are needed for the installation: light bulb (A19 100 watt maximum), safety glasses, wire stripper, step ladder, Phillips and flathead screwdrivers, wire cutters, and electrical tape.
4. Select a mounting option: flush mount or semi-flush mount.
5. To flush mount, follow these steps:
6. Loosen the nut (H1) and disassemble canopy (D).
7. Remove the crystal with rod set assembly (J1).
8. Thread the nut (G1) onto the nipple (F1) and thread the nipple (F1) into the coupling (H).
9. Slide the tube (E1), the cap (D1), the canopy (D), the metal washer (C1), the lock washer (B1), the ground wire (A1) and the lock washer (Z) onto the nipple (F1), then secure with the nut (Y).
10. Place the saddle (I) of the shade (X) on the main body (J), and secure with the screws (G).
11. Install light bulbs (not provided). Do not exceed the maximum capacity of watts recommended in the socket.
12. Thread the nut (L) onto the nipple (M) and thread the nipple (M) into the coupling (K).
13. To semi-flush mount, follow these steps:
14. Thread the nipple (F) into the coupling (H).
15. Place the saddle (I) of the shade (X) on the main body (J), and secure with the screws (G).
16. Install light bulbs (not provided). Do not exceed the maximum capacity of watts recommended in the socket.
17. Thread the nut (L) onto the nipple (M) and thread the nipple (M) into the coupling (K).
18. If you have additional questions, check out Signature Hardware’s Help Center at www.signaturehardware.com for product and warranty information or contact their Customer Relations team through live chat or by emailing support@signaturehardware.com.

SEMI-FLUSH MOUNT LIGHT

SKU: 440804

BEFORE YOU BEGIN
We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or for personal injury during installation.
Observe all local plumbing and building codes.
Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer __Relations team via live chat at www.signaturehardware.com or by emailing support@siganturehardware.com.

GETTING STARTED
Ensure that you have gathered all the required materials that are needed for the installation.

FOR YOUR SAFETY
WARNING: Be sure the electricity to the wires you are working on is shut off, either the fuse is removed or the circuit breaker is shut off. You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Under no circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on a ceiling which contains a radiant type heating system. Read instructions carefully, if you are unclear as to how to proceed, consult a qualified electrician.

INSTALLATION (FIG. 1)

FLUSH MOUNT

1. Please loose the nut (H1) and disassemble canopy (D).
2. Remove the Crystal with rod set assembly (J1).
3. Thread the nut (G1) onto the nipple (F1) and thread the nipple (F1) into the coupling (H).
4. Slide the tube (E1), the cap (D1), the canopy (D), the metal washer (C1), the lock washer (B1), the ground wire (A1) and the lock washer (Z) onto the nipple (F1), then secure with the nut (Y).

SEMI FLUSH MOUNT

1. Thread the nipple (F) into the coupling (H).

FLUSH MOUNT AND SEMI FLUSH MOUNT

1. Place the saddle (I) of the shade (X) on the main body (J), and secure with the screws (G).
2. Install light bulbs (Not provided). Please do not exceed the maximum
3. Thread the nut (L) onto the nipple (M) and thread the nipple (M) into the coupling (K).
4. Slide the glass (N), the plastic washer (O) and the metal washer (P) onto the nipple (M), then secure with the nut (O).
5. Slide the cap (R), the plastic washer (S), the crystal (T), the tube (U) and the plastic washer (V) onto the nipple (M), then secure with the finial (W).

INSTALLATION (FIG. 2)

1. Thread the mounting screws (A) into the matching holes in the circular strap (B).
2. Secure the mounting bar (B) to the outlet box with outlet box screws (C).
3. Please not : The ribbed wire will be a neutral wire, and the smooth wire will be a lead wire. The smooth wire will also have a printed temperature warning. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician.
4. Connect the white wire from the fixture to the white wire from the outlet box and the black wire from the fixture to the black wire from the outlet box. Cover the two wire connections using the two provided wire connectors. Wrap the two wire connections with electrical tape for a more secure connection. Attach the grounding wire connections with electrical take for a more secure connection. Connect the copper ground wires from the fixture and from the outlet box to the ground screw on the mounting bar.
5. Note : If you have electrical questions, consult your local electrical code for approved grounding methods.
6. After wires are connected, tuck them carefully inside outlet box. Raise the canopy (D) allowing for the mounting screws (A) to protrude through the holes on canopy (D), and secure with the ball nuts (E).

References

• ware
• Signature Hardware - Shop Unique, Quality Decor

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>