SIGNATURE HARDWARE 434135 Turnberry 1-Light 12-Inch Speckled Bronze Incandescent Flush Mount Light Owner’s Manual

434135 Turnberry 1-Light 12-Inch Speckled Bronze Incandescent Flush Mount

Light

Product Information

TURNBERRY

SKU: 434135

• Recommended tools and materials for installation:
  • Wire Connectors (3pcs)
  • Mounting Screws (2pcs)
  • Ground Screw (1pc)
  • Mounting plate (1pc)
  • Rubber washer (1pc)
  • Damp cloth for cleaning
• Care and Maintenance:
  • Wipe with damp cloth for cleaning
  • Avoid using abrasive cleaners or cleaners containing alcohol
  • Shut off main power supply before cleaning product or changing light bulbs

Product Usage Instructions: TURNBERRY

1. Before starting the installation, make sure to consult a professional if you are unfamiliar with installing electric fixtures. Observe all local plumbing and building codes.
2. Unpack and inspect the product for shipping damage. If you notice any damage, contact Signature Hardware customer support at www.signaturehardware.com or by emailing support@siganturehardware.com.
3. Gather all the required materials needed for installation as per the recommended tools and materials mentioned in the manual.
4. Shut off the power at the circuit breaker and remove the old fixture, including the crossbar.
5. Carefully unpack the new fixture and lay out all the parts in a clear area. Take care not to lose any small parts necessary for installation.
6. Attach the mounting plate (E) to the outlet box (G) (not supplied) using the 2 screws (B) provided with the outlet box (G).
7. Connect the electrical wires as follows:
   • Connect the black wire from the fixture to the black (hot) house wire.
   • Connect the white wire from the fixture to the white (neutral) house wire.
   • Make sure all wire nuts are secured. You may wrap the connections with electrical tape.
   • If your outlet has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect fixture’s ground wire to the ground screw (1pc).
8. After connecting the wires, attach the fixture to the mounting plate (E) using the 2 mounting screws (B) provided.
9. Turn on the power at the circuit breaker and test the fixture to ensure it is functioning properly.
10. If you have any questions or concerns, refer to the Help Center at www.signaturehardware.com or contact Signature Hardware customer support through live chat or by emailing support@signaturehardware.com.

OUTDOOR FLUSH MOUNT LIGHT

SKU: 434135

BEFORE YOU BEGIN
We recommend consulting a professional if you are unfamiliar with installing electric fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing, sink, counter top, or for personal injury during installation.
Observe all local plumbing and building codes.
Unpack and inspect the product for shipping damage. If any damage is found, contact our Customer __Relations team via live chat at www.signaturehardware.com or by emailing support@siganturehardware.com.

GETTING STARTED
Ensure that you have gathered all the required materials that are needed for the installation.

CARE AND MAINTENANCE:
To clean, wipe with damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.

RECOMMENDED TOOLS AND ACCESSORIES

SAVE THIS MANUAL: RETAIN FOR CONSUMER’S USE. READ THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLING THE PRODUCT: FOR PRODUCT OR INSTALLATIO QUESTIONS PLEASE CALL CUSTOMER. SERVICE AT 1‐800‐221‐3379.

INSTALLATION

1. Shut off the power at the circuit breaker and remove old fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
3. Attach the mounting plate (E) to the outlet box (G) (not supplied) using the 2 screws (B) provided with the outlet box (G).
4. CONNECTING THE WIRES Now connect the electrical wires as follows: Connect the black wire from the fixture to the black (hot) house wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet has a ground wire (green or bare copper), connect fixture’s ground wire to it. Otherwise, connect fixture’s ground wire directly to the mounting plate by using the green screw provided. Tuck the wire connections neatly into the junction box.
5. Attach the cage (L) to the mounting plate (E) and then secured by the ball nut (F).
6. Attach the glass (H) to cage (L) and then secured by the rubber washer (J ) and cap nut (I ).

References

• Signature Hardware - Shop Unique, Quality Decor

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>